brand new VW Engine gasoline 1,4 Ltr. TSI - 150 PS with Turbo: 04E145721F; Ignition coils 04E905110M; throttle body 03F133062B; fuelpump; flywheel, fit in: AUDI Q3 1.4 TSI, Bj. 2013- VW CC 1.4 TSI, Bj. 2015-2016; VW Tiguan Allspace 1.4 TSI, Bj. 2017-; VW Passat 1.4 TSI, Bj. 2014-; Sharan, Touran 1.4 TSI, Bj. 2015-; Tiguan 1.4 TSI, Bj. 2016-; Beetle 1.4 TSI, Bj. 2014-; Scirocco 1.4 TSI, Bj. 15-17; Golf VI 1.4 TSI, Bj. 2013-; Jetta IV 1.4 TSI, Bj. 2014-; Tiguan, Golf VII, Vento IV SKODA Kodiaq 1.4 TSI, Bj. 2016-; Supeb III 1.4 TSI, Bj. 2015-; Yeti, Octavia III SEAT Alhambra, Leon --- available Qty: 96 pieces
MERCEDES BENZ A-Claas (W176) ; B-Claas (W246, W242), C-Claas (W204) CLS (C218, C219, X218, CLA 200 CDI (X117), Bj. 2015-2019; GLA (X156), Bj. 2013- E-Claas (W212, A207, C207, S212), M-Claas (W166) Dieselmotor, 4 Zylinder (short running) 3 km; 100 kW; Euro 6; with Alternator, AC Compressor, slide valve (electronic throttle gas cooler), exhaust manifold, exhaust gas cooler, high pressure pump, Turbocharger, vacuum pump (mechanical), glow time output stage, 2-mass-flywheel, this engines was short running - takte off from tested car -
BMW 3 (F30) 340 i, Bj. 2015-2018; BMW 3 (F30) 340 i xDrive, Bj. 2015-2018 gasoline BMW (new) 3,0 Ltr. 6 Zylinder, AWD / 2WD; with Fuelpump and Injectors 16 pieces available
When smeared on your skin Holzhacker intensive insect lotion protects you from itching and dangerous insect stings and at the same time cares for your skin. The intensive protection insect lotion in the practice pump spray well tried all over the world and is ideal for travelling, leisure time or sport.
Spare supplier and our core spares:AC Compressors, alternators, calipers, clutches, drive shafts, distributors, master cylinders, power steering gears, power steering pumps, rack & pinion steering units, starter drives, solenoids, starters, turbochargers.
Hygiene article: baby care, body care, dental care, face care, foot care, fragrance, hair care, hand care, hair removable, sun care.
Purified Water(Aqua) Propylene Glycol, Sodium Silicate, Magnesium Aluminum Silicate, Acetyl Hexapeptide - 8, Hydrolyzed Rice Protein, Soluble Collagen, Cellulose Gum, Xantham Gum, Titanium Dioxide, Cl 77491, Cl77492, Phenoxyethanol Ethylhexylglycerin. 2. How do you use Plexaderm Rapid Reduction Serum? - Wash and dry skin - Slowly press down on pump to dispense a small amount of serum onto fingertip(start with about half - the size of a pea). - Gently apply a thin, even layer to targeted areas, being careful to avoid contact with eyes. - Allow Plexaderm to set and dry(10 minutes for optimal results).
B.AL/PE – Foils for recycling aluminium AL/PE foils, bales, hand-assorted, from packaging industry abt. 25 mts/40’ ctr. - on-going 1.AL/PE foils 50/50 AL/PE + 60/40 AL/PE mixed per bale – abt. 50% each 400 mts todayEURO 525,--/mt cfr Hong Kong incl. THC + ingate charges 2.AL/PE foils 70/30 AL/PE 300 mts todayEURO 655,--/mt 3.AL/PE foils 80/20 AL/PE 50 mts todayEURO 795,--/mt Pictures upon request.
CARDINAL FLEXAL 200 COUNT / BOX OTG USA GO A2A TOMORROW ASAP WITH YOUR BCL+ATV PRODUCT IS 100% OTG* RWA IS IN HAND 1-NCNDA - NAMES, POSITIONS, EMAILS 2-LOI+LOA+ICPO plus KYC-CIS + AUTH LETTER + IMFPA in our template 3. PROOF UP ON 4/8/2021 with BCL & ATV from Major US Bank. Must have US attorney. NO - NADA - NEVER SEND US A RENTED BCL's (Santander or US Capital Private Equity) 4. SGS Exchange + SPA Signed 5-Open | Fund Escrow - Common Escrow Account with Moseley & Lester 6-Inspect 7-Release Escrow Funds 9-Pick Up per SPA Delivery Schedule
B. AL/PE – Foils for recycling aluminium AL/PE foils, bales, hand-assorted, from packaging industry abt. 25 mts/40’ ctr. - on-going 1. AL/PE foils 50/50 AL/PE + 60/40 AL/PE mixed per bale – abt. 50% each 400 mts today EURO 525,--/mt cfr Hong Kong incl. THC + ingate charges 2. AL/PE foils 70/30 AL/PE 300 mts today EURO 655,--/mt 3. AL/PE foils 80/20 AL/PE 50 mts today EURO 795,--/mt Pictures upon request.
Don't mistake the purity of copper bars with the copper wiring you can buy from your local hardware store. Generic copper wiring has lower purity, being alloyed with other metals to achieve particular characteristics needed for the application. Copper bullion bars, on the other hand, are usually sold with a 99.9% copper consistency. Copper bars come in different shapes as well. One of the most popular choices for investors is the copper cube. It makes for an interesting display piece as well as a good investment opportunity. Copper bars also come in a variety of sizes and weights. A diversity of items with different price points can be useful in your holding, particularly if the metal should be needed for barter and trade. You can find 99.9% copper bars as light as one-ounce pieces and as heavy as 10-pound bars.
SBP 200 This cabinet bale press has a large filling volume with easy filling due to a large filling opening. Knuckle-joint press pistons with thrust-twist motion for pressing operation. Simple operation due to two-hand-handling absolutely safe. Hoop band positioned visibly and easy to change. This system has a bale ejection aid. This press enables a trouble free operation due to the compact and strong construction. Technical data: Pressure:............................200 kN/m2 - abt. 20 t Drive:..................................4,0 kW/400 V/50 Hz Cycle time:..........................40 sec. Feed opening:.....................1200x700 mm Bale dimensions:................1200x700x500 ..........................................up to 800 mm weight of bale:.....................50 up to 200 kg press length:.......................1990 mm press width:........................1360 mm press depth:........................1170 mm weight.................................1300 kg electric control ready to plug in
SBP 100 This cabinet bale press has a large filling volume with easy filling due to a large filling opening. Knuckle-joint press pistons with thrust-twist motion for pressing operation. Simple operation due to two-hand-handling absolutely safe. Hoop band positioned visibly and easy to change. This system has a bale ejection aid. This press enables a trouble free operation due to the compact and strong construction. Technical data: Pressure:............................100 kN/m2 - abt. 20 t Drive:..................................4,0 kW/400 V/50 Hz Cycle time:..........................40 sec. Feed opening:......................600x600 mm Bale dimensions:.................500x700x500.- 900 mm weight of bale:.....................50 up to 80 kg press length:.......................1120 mm press width:.........................830 mm press height:.......................2000 mm weight.................................980 kg electric control ready to plug in
Iranian products like carpet and rugs and kilim, pistachio, raisin, dried fruits, fresh fruits, watermelon, pepper, kiwi, melon, saffron, dates, licorice, rose products, cumin, blue salt, malayer raisin, sultana raisin, pickles, general purpose polystyrene, gpps, gypsum, lead, bitumen, ceramic, tiles, faucet, polymer, pet, tomato paste, sauce, canned fruits, canned vegetables, canned bean, canned corn, mineral water, cosmetic products, hand cream, paper tissue, toiled paper, hair color, pasta, diary products, sugar, rock candy, energybar, apple, apple chips, barberry, dried vegetables, jelly powder, dessert, cucumber, plug, receptacle, wall plug, car mat, plastic car carpet, dash mat, pvc floor liner, tool bag, trash bag, sun visor, 3d car mat, plastic tools, plastic container, plastic basket, hairpin, slipper.
Introduction: The LED660V is a professional LED pick and place machine, features high-speed and high-accuracy. It is your optimal solution for LED circuit board high-volume assembly. Features: 1. Board driving system uses high precision step motor, which is driven by an industrial belt. It cooperates with a precision guide-rail to improve the placement accuracy and board driving speed. 2. Integrated 6 mounting heads driving system with servo motor. Together with the high precision ball screw, it achieves the complete pick and place process of the LED components. 3. The 6 groups of mount heads improves the production efficiency of 400%, compared with 1 group of heads. 4. Automatic visual programming. No need of manual input of the component coordinates. Programming is simple and fast, a new program is finished within 10 min. 5. Different sizes of smart feeders, which will not move if the component stuck or isn’t picked up properly. 6. The LED660V is a cost-effective mounter which suits optimal a high-volume LED production. 7. The whole machine is controlled by an industrial computer with professional software, easy to operate and use. 8. Easy to import CAD data of the circuit boards. 9. Stable and easy to complete the programming and placement of LED panel board. 10. The coordinates of the PCB can be displayed, opportunity of a fine adjustment for these coordinates to achieve high-precision placement. 11. The space of panel board can be set in the software, all component placing coordinates will be shown according to the space of panel board. Selection of PCBs, which shall not be mount is possible as well. 12. If the board have manufacturing quality problems, the LED660 can shift the component place for accurate mounting. 13. The software includes a 6 grades speed changing function, you can find your adequate speed according to the distance check sheet. Besides, the speed adjustment can increase the stability for long time usage. 14. The PCB platform has a vacuum absorb function, which can help large-size PCBs and FPCs to position accurately and improve the placement accuracy. 15. Integrated vacuum pump inside the machine, no need to configure it separately. 16. The LED660V is a special LED mounter, which can mount all kinds of SMD LED chips, all components above 0402 (except more than 5mm Aluminum electrolytic capacitors ), cylindrical diodes, transistors, SOPs, and SOTs smaller than 20mm IC. Technical Parameter: Mounting heads: 6pcs Max size of PCB: 1200 x 350mm Max moving range: X-axis: 1500mm, Y-axis: 410mm Max moving range of Z-axis: 15mm Typical mounting speed: 13.000 - 14.000cph Max mounting speed: 18.000cph Mounting accuracy: +/- 0.1mm Positioning method: Visual positioning Component available: SMD components >0603 and LEDs, SOTs, SOPs Program method: Automatic data import/ video study/ keyboard input Belt feeder: Optional: 8mm, 12mm, 16mm, 24mm Number of feeders: 6pcs of GF feeder can be set, optional 12 feeders possible. Operation system: Windows XP Air pressure: Internal vacuum Power supply: 220V,50Hz, 4.5kW Weight: 500kg Dimension: 2600 x 680 x 1500mm
Introduction: The TP-serie are machines describing fully automatic vision SMT pick and place machines, which can mount a variety of components through the vacuum nozzle. The TP66V is suitable for most of the SMD components such as 0402, SOICs, PLCCs and QFP ICs. With the vision position system it is able to mount 0.5mm of QFP ICs or BGAs. Beside the standard circle reference point, also a square point, which is not the PCB solder paste screen printing pad ring perforated pad, can be chosen as a reference point. Features: 1. Using imported precision square rail, effectively improve the placement accuracy. 2. Using an unique high-definition optical prism industrial camera to complete mount high-precision components. 3. With the vision position system, it can automatically identify the MARK point to improve effectively your SMT production efficiency and placement accuracy. 4. Automatic visual programming. There is no need of a manual input the coordinates of components. 5. Standard configuration of automatic nozzle replacement system. 6. Able to configure a variety of different feeders to meet your needed requirements for mounting. 7. Easy to input CAD data of the PCB. 8. The software can display all PCB coordinates, which you can adjust by fine tuning some of the coordinates to assure a high precision placement. Standard Configuration: 1. Industrial Computer: 1 piece 2. Mounting head: 1 groups 3. Nozzles: 9 pcs 4. GFTA-48 feeder table: 2 sets 5. MARK cameras: 2 sets 6. QFP high precision industrial camera: 1set 7. QFP high clear light source: 2 set Optional: 1. Automatic feeder: 8mm, 12mm, 16mm and 24mm 2. IC Disc Feeder(GFQN) 3. Components bulk disk(GFSN) 4. Nozzles 5. AQ38 end mirror system(25MM-38MM QFP) 6. AQ45 end mirror system(38MM-45MM QFP) 7. Industrial air pump Technical Parameter: Mounting head: 2 units - 12 heads Max size of PCB: 1500 x 316mm Min width of PCB: 40mm Max moving range: 670 x 620mm Max thickness of components: 15mm Typical speed: 14.000 - 17.000cph Max speed: 32.000cph X, Y-axis precision: 0.002mm Mounting precision: +/- 0.03mm Available components: > 0402 and < 38mm pitch; > 0.5mm IC Positioning: Visual positioning Program method: Automatic data import/ video learning/ keyboard input Transmission: X, Y-axis high precision ball screw with precision guide rail Tape feeder: Optional 8mm, 12mm, 16mm, 24mm, 32mm, 44mm Number of Feeders: Possibility of 96 feeders of 8mm GFTA-08S feeder, 48 feeders for the front and 48 for the back side. Number of IC feeder: Max 2 pcs Operation system: Windows XP Compressed air: 80psi (0.5Mpa - 0.7Mpa) Power supply: 220V, 50Hz, 5kW Weight: 14000kg Dimension: 1650 x 1485 x 1400mm
The CNC3200A is the optimal solution to manufacture double sided circuits. The standard configuration includes an automatic replace tool system and a high-precision screw made in Germany. Equipped with a three axis controller and a high precision step motor to control the X, Y and Z-axis. Features: A. advanced: suit for double side PCB ,can engrave ,drill, cut the PCB. B. effective: it takes only several minute to finish one PCB. C. high precision: Standard configure Germany precision screw and three axis controller with high precision step motor; control the X Y Z axis precision to make sure the high precision. D. convenient: software installation is easy and suit for variety PCB. E. confidential: no need outsourcing processing ,lab can finish the whole process . F. software is powerful, convenience and fast, have memories for processing, can continue to work when interrupt at any process. G. With three face transparent sound insulation dust-proof covers, suitable for teaching demonstration and observation angles, and the front door with safety device to protect the safety of operators H. standard configure tool cooling system, can prolong the lifetime of the tool, also can improve the precision. I. Carving process can remove the excess of copper all laid or remove the copper on the line, remain the excess copper, saving time and improve the effective. J. multi-function transfer software is suit for variety PCB design software. K standard configure automatic replace tool system, can automatically replace 9 pcs tools, extend up to 18 pc tools (optional). L. Configuration sound insulation dust cover, and safety device, can make sure the safety of operator when working. Technology parameters: 1. Min line diameter: 4mil 2. Min line width: 0.15mm 3. Minimum insulation spacing: 0.15mm 4. Repeated precision: 0.02mm 5. Min hole diameter: 0.15mm 6. Transmission resolution: 0.001mm 7. Work table: 310*410*130mm, work size: 500*375mm 8. Spindle speed: 10000-60000RPM Infinitely adjustable, spindle power: 200W to 250W. 9. Three axis speed: 100*100*100mm 10. Automatically replace tools: 9 pcs tools, 3mm - 3.175mm, can add up to 36pcs tools. 11. Drilling speed: Max 100pc/min 12. Transmission way: standard configure Germany precision screw and three axis controller with high precision step motor, Pneumatic tools chuck, fabrics hood. 13. Flatness compensation: The flatness of PCB make assures high-precision results. 14. Lighting device: With lighting device, convenient to view the engraving process. 15. Dust collection device: professional dust collection device to assure that the inner body is clean, which is makes the engraving process viewable. Optional: Use of vacuum worktable. 16. Software: Includes a professional automatic tool, multi-axial engraving software, easy to input NCP, PLT, DIN 66025 format. 17. Protective cover: can view at 360 angel, also with safety switch to make sure the operator’ safety. 18. Operating system: Win98/ 2000/ XP 19. Min memory: 512MB 20. Handheld magnifying glass: Magnification of 40 times with mm scale and lighting. 21. Special air pump: 30L air cans, max air pressure is 8 bar, air flow is 100 L/min. 22. Dimension: 700*700*700mm 23. Speed of no load: 100mm/s 24. Trough mill speed: 6mm/s
Second hand clothing, original second hand clothing.
Hand Gloves And Face Masks.
Second hand clothes.Shipping