Calcium Chloride, White Cement, , Rdp, Bentonite, Cellulose Fiber, Caustic Soda, Calcium Carbonate And Titanium Dioxide..
Low Density Polyethylene TASNEE produces four different low density polyethylene film grade resins using tubular reactor technology with melt flow rates (MFR) range of 0.25 4.0 g/10min. TASNEE LDPE grades exhibit mainly excellent dart impact, high puncture & tear resistance, shrink ability and seal ability. TASNEE low density polyethylene is manufactured using the Lupotech T method and has certain advantages that makes it most feasible to film applications: It does not allow water and steam to permeate but has a good permeability for carbon dioxide and oxygen. These characteristics are especially desired for packaging. Non-oxidizing acids, bases, salts and their solutions practically have no effect on polyethylene. Major applications include: TASNEE LD 0222N Heavy duty packaging, shrink wrap film, agricultural film, etc. TASNEE LD 0725N Medium duty packaging, shrink wrap film etc. TASNEE LD 1925AS (additivated) Bags, pouches, food packaging lamination film, shrink film, etc. TASNEE LD 4025AS (additivated) Lamination film, laundry bags, shrink film, food packaging pouches, etc.
A cement is a binder, a substance used for construction that sets, hardens, and adheres to other materials to bind them together. Cement is seldom used on its own, but rather to bind sand and gravel (aggregate) together. Cement mixed with fine aggregate produces mortar for masonry, or with sand and gravel, produces concrete. Cement is the most widely used material in existence and is only behind water as the planet's most-consumed resource. Cements used in construction are usually inorganic, often lime or calcium silicate based, and can be characterized as either hydraulic or non-hydraulic, depending on the ability of the cement to set in the presence of water (see hydraulic and non-hydraulic lime plaster). Non-hydraulic cement does not set in wet conditions or under water. Rather, it sets as it dries and reacts with carbon dioxide in the air. It is resistant to attack by chemicals after setting. Hydraulic cements (e.g., Portland cement) set and become adhesive due to a chemical reaction between the dry ingredients and water. The chemical reaction results in mineral hydrates that are not very water-soluble and so are quite durable in water and safe from chemical attack. This allows setting in wet conditions or under water and further protects the hardened material from chemical attack. The chemical process for hydraulic cement found by ancient Romans used volcanic ash (pozzolana) with added lime (calcium oxide). Portland cement is by far the most common type of cement in general use around the world. This cement is made by heating limestone (calcium carbonate) with other materials (such as clay) to 1450 �°C in a kiln, in a process known as calcination that liberates a molecule of carbon dioxide from the calcium carbonate to form calcium oxide, or quicklimeâ??which then chemically combines with the other materials in the mix to form calcium silicates and other cementitious compounds. The resulting hard substance, called 'clinker', is then ground with a small amount of gypsum into a powder to make ordinary Portland cement, the most commonly used type of cement (often referred to as OPC). Portland cement is a basic ingredient of concrete, mortar, and most non-specialty grout. The most common use for Portland cement is to make concrete. Concrete is a composite material made of aggregate (gravel and sand), cement, and water. As a construction material, concrete can be cast in almost any shape, and once it hardens, can be a structural (load bearing) element. Portland cement may be grey or white.
Clinker consists of various calcium silicates including alite and belite. Tricalcium aluminate and calcium aluminoferrite are other common components. These components are often generated in situ by heating various clays and limestone. Portland cement clinker is made by heating a homogeneous mixture of raw materials in a rotary kiln at high temperature. The products of the chemical reaction aggregate together at their sintering temperature, about 1,450 C (2,640 F). Aluminum oxide and iron oxide are present only as a flux to reduce the sintering temperature and contribute little to the cement strength. For special cements, such as low heat (LH) and sulfate resistant (SR) types, it is necessary to limit the amount of tricalcium aluminate formed. The major raw material for the clinker-making is usually limestone mixed with a second material containing clay as source of alumino-silicate. Normally, an impure limestone which contains clay or silicon dioxide (SiO2) is used. The calcium carbonate (CaCO3) content of these limestones can be as low as 80%. Second raw materials (materials in the rawmix other than limestone) depend on the purity of the limestone. Some of the second raw materials used are: clay, shale, sand, iron ore, bauxite, fly ash and slag. The clinker surface and its reactions in different electrolytic solutions are investigated by scanning electron microscope and atomic force microscopy. Portland cement clinker is ground to a fine powder and used as the binder in many cement products. A little gypsum is sometimes added. It may also be combined with other active ingredients or chemical admixtures to produce other types of cement including: ground granulated blast furnace slag cement.
Urea, also known as carbamide, is an organic compound with chemical formula CO(NH2)2. This amide has two NH2 groups joined by a carbonyl (C=O) functional group. Urea serves an important role in the metabolism of nitrogen-containing compounds by animals and is the main nitrogen-containing substance in the urine of mammals. It is a colorless, odorless solid, highly soluble in water, and practically non-toxic (LD50 is 15 g/kg for rats).[5] Dissolved in water, it is neither acidic nor alkaline. The body uses it in many processes, most notably nitrogen excretion. The liver forms it by combining two ammonia molecules (NH3) with a carbon dioxide (CO2) molecule in the urea cycle. Urea is widely used in fertilizers as a source of nitrogen and is an important raw material for the chemical industry. Urea is used to treat dry/rough skin conditions (e.g., eczema, psoriasis, corns, callus) and some nail problems (e.g., ingrown nails). It may also be used to help remove dead tissue in some wounds to help wound healing. Urea is known as a keratolytic. Urea is an inexpensive form of nitrogen fertilizer with an NPK (nitrogen-phosphorus-potassium) ratio of 46-0-0. Although urea is naturally produced in humans and animals, synthetic urea is manufactured with anhydrous ammonia. Although urea often offers gardeners the most nitrogen for the lowest price on the market, special steps must be taken when applying urea to the soil to prevent the loss of nitrogen through a chemical reaction. Nitrogen Content Wt % : Min 46 Biuret Content Wt % : Max 1.0 Moisture Wt% : Max 0.3 Particle Size (1-2.4mm) % :Min 90 Or 2-4 Mm Granular Urea Urea Formaldhide (UF) % : Max 0.4 Packing : 50 Kg Bags / Bulk Urea
