Description CC-100M is a waterproofing additive for concrete, mortar and cementitious grout. Use Beams, foundations, masonry laying, floor and wall cladding mortars, plasters, slabs, slope walls, buried structures (water tanks, reservoirs and pools), waterproofed, reinforced and reinforced concrete, etc. Technical Data and Property Ambient temp.: 25, 50±5% R.H. Packaging : 20kg /pail Appearance : Grayish white powder Odor : Odorless pH : 12 ~ 13 Relative Density : 1.9 ~ 2.1 g/cm3 Absolute Specific Mass : 2.2 ~ 2.7 g/cm3 Flammability : Non-flammable Solid Solubility : insoluble **Results have been obtained from tests performed under standard conditions and may vary depending on application conditions.
DESCRIPTION CC-200 is a indoor, high fluidity, rapid strength and leveling material. It still has high bonding,low shrinkage, low water absorption, acid resistance, alkyl resistance and chemical resistance. It special use for fast repairing, putty and leveling for epoxy coating. APPLICATION Floor fixing on parking garage, factory, and warehouse. Leveling before epoxy coating. Basic layer for non natural paint. Bec ause of the early strength and low moisture content, CC 200 has widely application. Contact out agent when you have doubt on CC 200. ADVANTAGES 1. Curing and enhancing are fast and rapid below 25 mins. High strength and low water absorption/ content could be reached after curing. 2. Good acid and alkyl resistance. 3. Good wear resistance, high compressive strength, leveling and anti cracking. PREPARE TO USE 1. Clean with vacuum to ensure the surface dustless. 2. Working site is free from dust, sand, oil, and loose. a). Crack and Joint Treatment b). File on the crack, open a width of 2 3 cm depth of 1 cm or more groove joints and clean up dust and loose. c). At the same time taking CC 200 mortar, filled in and up the crack and sizing 1 2 times primer after 2 4 hours. 4. Shorter wor king hours to achieve saving time, fast leveling and convenience work.
Product Description Oxidized bitumen is high quality, general purpose oxidized bitumen for various applications. Uses Foundation damp-proofing Built-up roofing systems. Roll and pour application of bitumen felts. Bonding of SBS modified membranes by hot mop method. Sealing of laps and joints of various bituminous felts and membranes. Wet area waterproofing. Bonding of wooden boardsâ?? insulation panels. Road resurfacing and repair. Application Heat the drum until the oxidized bitumen starts melting at approximately 130Deg.C. Apply by roller. Squeegee or direct rolling to an average rate of 1Kg/sq.m. For hot mop application. The membrane should be applied while pouring to avoid re-cooling. Packing In steel drum(180KGS) In SEALEDBAGS(25KGS/40KGS)
Description CP-358W2K is a product which can be painted on rusty iron sheet, iron and other alloy products. Normally, iron products should get the rust removal by sand blast first when they get rusty. Then, they get painted with the anti-rust coating and fireproof paint. If it does not get the rust removal first and directly get painted, the rust will spit out. But, the same situation will not happen if using CP-358W2K. Features/Advantages Quick and easy to use. Fireproof coating. â?? Hydrophilic. â?? Water-based. â?? Non-toxic & smokeless. Environmentally friendly. Can be applied well on steel construction body, steel bar, and steel sheet. Does not blister and get damaged when burning. Rust removal is not required when applying CP-358W2K (unless the rust is thick). Applications Can be used in rocket missile or products that high-temperature application is required. Heating pipe. Iron plate or sheet. Indoor/outdoor fireproof paint. Multiple iron materials/fireproof paint. Plywood, veneer board. Fire door surface treatment.
DESCRIPTION CC-610 Modified Polyurethane weather shield is a two component with great bonding strength on materials that are hard to adhere. CHARATERISTIC Dust proofing and possessing self cleaning capability Excellent water and weather resistance Firm coatings with good alkaline resistance Fast setting rate and easy to apply APPLICATION Coating oil or color changing for tiles, imitation rocks. Glass painting and painting for iron, zinc plate, and stainless steel High weather resistance and high gloss corrosion prevention paint for cement, stones, asbestos, bricks, wooden materials, and bamboo wood. Color : Clear & standard colors Viscosity : 75-110 KU Solid content : 30%-55% Coating time interval : 2 hours minimum Weight mixed ratio : Clear/1 0 : 1 Colored/1 1 : 1 Packaging Clear 14kg : 1.4kg (5 gallon per set) Colored 20kg : 1.8kg (5 gallon per set) Apply methods Brush, spray, roller coating
Description Wallpaper adhesive is a high quality, easy to mix adhesive. It is easily spread with excellent slip properties for accurate positioning and longlasting results. Suitable for hanging all wallpaper types. Features â?? This product is made of natural cassava flour after gelatinization and modification, and added with water resistance additives. It has high adhesiveness and is not easy to hydrolyze after film formation. â?? It can be used in cold water. Its characteristic of dispersing first and then dissolving makes it difficult to form fish eye colloid under a large amount of powder. â?? Non-toxic, tasteless, easy to clean. â?? During use, the amount of water can be increased or decreased according to the characteristics of the material to control the adhesion. Application 1. Wallpaper adhesive. 2. Poster. Stamp adhesive. Precautions 1. If bubbles are generated during the mixing process, they must wait for the bubbles to disappear before they can be used on the material 2. The mixed colloid cannot be stored for too long, it is recommended to use it up within 3 days 3.If the colloid that has been stored for too long has a peculiar smell, there will be black hair and yellow on the side of the barrel or the surface of the colloid. It cannot be used and needs to be re-modulated Package 5kg/barrel (20L barrel. Plastic bag inside) 35kg/barrel (big blue barrel, lined with plastic bag)
CP-201 is a three-component material. With organic and inorganic complex, it can provide a solid, and thermal shock resistant floor. It is solvent free and is a â??Green Productâ??. The finish is easy to clean, water-resistant, abrasion- resistant and good impact- resistant. With binary complex bond, it can resist the growth of moulds. Feature solvent-free, friendly to human. compression and impact resistant. chemical resistant as its special structure. suitable for critical area (0~80â??). suitable for food factory, freezer, medicine plant, chemical plant, laboratory..etc Application A. Substrate preparation: 1.Ensure that the substrate is solid and remove dust, grease or other contaminants by grinding or blasting. 2.Enhance bonding with anchor grooves. B. Application of CP-201 1. Prime the substrate with PU primer. 2. Mix A, B and C continuously until it becomes a smooth and lump-free paste. Apply the mixture with special feeder to designed thickness and smooth the finish with steel trowel or spatula for use. Do not apply it without professional workers.
DESCRIPTION CC-610S Modified Polyurethane weather-shield is a two component with great bonding strength on materials that are hard to adhere. CHARATERISTIC More suitable coating on surface as soft plastic, PVC, ABS, PCâ?¦..etc. Non-yellowish and excellent gloss and color retention after exposure in outdoor. Resist from most chemical products Coating oil or color changing for tiles, imitation rocks. Glass-painting and painting for iron, zinc plate, and stainless steel High weather resistance and high gloss corrosion prevention paint for cement, stones, asbestos, bricks, wooden materials, and bamboo wood. NOTES Please mix and stir well before using Please make sure the lid is closed tightly. Please keep the surface free of dust, loose or paint before painting The tools are washable by solvents after application. Avoid direct sunlight or high temperature environment to ensure excellent product quality. Keep the storage environment well ventilated and stay away from flammable when applying paints. The actual volume application depends on the surface condition.
DESCRIPTION CA-055 is an emulsion primer of water-based acrylic resin with excellent properties such as water resistance, pull-off strength and pore-filling ability etc. , especially used to improve the physical properties of cement. It can be mixed with water at any ratio. FEATURES Excellent penetration into the concrete substrate to increase pore-filling ability and adhesion. Reduced transport paths of concrete structure to enhance durability. Excellent water resistance. AREA OF APPLICATIONS Repair mortar for concrete areas. Industrial flooring. Bonding agent for new to old concrete. As cement grout additive. As water-based primer. For making two component tile adhesives. As adhesion aid for skim coat materials. PACKAGING 5 gallon Plastic Pails FLAMMABILITY Being water-base, it is non-flammable.
DESCRIPTION CA-055(W12) is an emulsion primer of water-based acrylic resin with excellent properties such as water resistance, pull-off strength and pore-filling ability etc. , especially used to improve the physical properties of cement. It can be mixed with water at any ratio. FEATURES *Excellent penetration into the concrete substrate to increase pore-filling ability and adhesion. *Reduced transport paths of concrete structure to enhance durability. *Excellent water resistance. AREA OF APPLICATIONS *Repair mortar for concrete areas. *Industrial flooring. *Bonding agent for new to old concrete. *As cement grout additive. *As water-based primer. *For making two component tile adhesives. *As adhesion aid for skim coat materials. PACKAGING 20kg Plastic Pails FLAMMABILITY Being water-base, it is non-flammable. CLEAN UP Tools and equipment can be easily cleaned up with cloth before drying.
Description CP-201 is a three-component material. With organic and inorganic complex, it can provide a solid, and thermal shock resistant floor. It is solvent free and is a â??Green Productâ??. The finish is easy to clean, water-resistant, abrasion- resistant and good impact- resistant. With binary complex bond, it can resist the growth of moulds. Feature solvent-free, friendly to human. compression and impact resistant. chemical resistant as its special structure. suitable for critical area (0~80). suitable for food factory, freezer, medicine plant, chemical plant, laboratory..etc
DESCRIPTION AS-650 is a flexible, two-components aromatic polyurethane protective coating. It can be used on various substrates for coating and protecting purpose, especially with the excellent adhesion ability with polyurea and polyurethane layers. It cures fast providing quick tack free time (1-2hours), allowing most projects to be completed within one day. CHARATERISTIC Fast drying and fast curing Brushable Solvent free Abrasion and mechanical stress resistant Chemical resistant (in diluted acids-alkalis, car oils, petroleum, etcâ?¦) APPLICATION AREAS Parking areas, warehouse ramps, garages, terraces Outdoor and indoor stores, industrial shop floors Outdoor laundries, gas station, etc
Description CC-105HD Duraflex is one component, eco-friendly, water-based topcoat membrane. Feature Resistant to exposed sunlight and chemicals. When applied, it forms as seamless membrane without joints. Product keeps its mechanical features over a temperature span of 40 to 90 Use Area Roof terraces balconies and verandas. Industrial floor coatings. Stones, marble and ceramic surfaces Coverage. Consumption of each layer: 0.1.5-0.2.5 kg/m2. Minimum two coats should be applied. Total consumption: approx. 0.3-0.5 kg/m2. Recoating: Do not exceed 48 hours between each coats. Application must be repeated if this time is exceeded.
One part, neutral, moisture cure, and high performance silicone sealant . It can be used for expansion joints, metal panels, glass, natural stones, window frames, etc. Excellent sealing forms elastomeric and waterproofing interface for most building substrates. Features & Benefits Enhance d building aesthetic performance prevents long term dirt (or residue) run down on metal panels and coated glass or staining of porous substrates Excellent adhesion to most building substrates, such as glass, metal, masonry ceramic tile, natural stone granite and polymer coating materials. Outstanding UV and weather resistance Free of plasticizer and oil. Non pollutant s on building materials Low modulus properties, excellent tensile strength and elongation It can be applied on the movement joints of highway, airport s, bridges, parking lots. Approvals Passes American standard specification ASTM C920. Meets Taiwanese Public Construction Commission, Executive Yuan silicone. specification : Chapter 07921. Meets the related standard specifications: CNS8903, CNS8904 , BS EN ISO11600 , and JIS A 5758. Packaging DS-900 is supplied in 300 Ml Cartridges.
Description OP-908 is solvent-based bituminous asphalt for cold application based on oxidized bitumen, inert fillers and additives. Application OP-908 is conceived for cold bonding of polymer bitumen membranes with finish of the lower face with sand or with mineral. It is also can be the bonding of waterproofing membranes to the vertical connections,exhaust outlets, skylights and aerators.
Rock-Loc is the best and most advanced synthetic dust suppression product. Using revolutionary technology, long-lasting Rock-Lock is engineered to meet the most demanding dust control situations. Scientifically formulated from the most environmentally sustainable feed stocks, this non-hazardous, road moisturizing emollient is crystal clear, completely odorless and easy to apply. Perfect for hard wearing areas such as cattle yards, stables, truck and loading yards.
Description CS-261 is a acrylic sensitive adhesives. It has good initial tack, suitable for the adhesion of PVC tile. It is easy to use. Application CS-261 can be used in decoration, PP to paper,PVC to non-woven fabrics industry.
Description CS-266 is solvent-free moisture curing PU adhesive. CS-266 temperature for foam or plastic, and products have properties as mentioned below : 1. Great curing speed. 2. Great bonding strength. 3. Great hydrolysis resistance. 4. Great weather resistance. 5. Great chemical resistance. Operation 1. CS-266 can be used by roller or knife coating. 2. After coating on the foamâ??s surface, then lamination stick with rollers. 3. Pressing the foam/foam at room temperature about 180 mins approximately, and initial binding strength can be obtained.
CA-107W is a water-based dispersion of SBR polymer, especially used to improve the physical properties of cement. It is formulated to increase the adhesion, durability and compressive strength of normal mortar. 1.Bonding of fresh mortar to old concrete. 2.Increase adhesion of vertical marbles,tiles. 3.Improve water-resistance when added to tile grouts. 4.Reduce shrinkage cracks. 5.Improve workability and abrasion resistance of screed. 6.Can be mixed with dry-packed,factory-blend mortar.
CC-402 is a one component, plasto-elastic coating based on UV-curing acrylic dispersion with excellent crack-bridging properties even at temperatures below 0°C. CC-402 complies with the requirements of EN 1504-2 as protective coating. CC-402 is used for protection and enhancement of concrete structures (normal and lightweight concrete),especially exposed outdoor concrete surfaces with a risk of cracking CC-402 is used with concrete repair works as an elastic protective coating on AFTEK smoothing mortar (refer to product / system data sheet), fiber cement and over coating of existing soundly adhering coatings. Suitable for protection against ingress (Principle 1, method 1.3 of EN 1504-9) Suitable for moisture control (Principle 2, method 2.3 of EN 1504-9) Suitable for increasing the resistivity (Principle 8, method 8.3 of EN 1504-9) Crack-bridging even at low temperatures (-5°C) High diffusion resistance against CO2 reducing the rate of carbonation Water vapour permeable Very good resistance against weathering and ageing Environmentally friendly (solvent free) .Reduced tendency to dirt pick up and contamination.
