Description
CP-358W2K is a product which can be painted on rusty iron sheet, iron and other alloy products. Normally, iron products should get the rust removal by sand blast first when they get rusty. Then, they get painted with the anti-rust coating and fireproof paint. If it does not get the rust removal first and directly get painted, the rust will spit out. But, the same situation will not happen if using CP-358W2K.
Features/Advantages
Quick and easy to use.
Fireproof coating.
â?? Hydrophilic.
â?? Water-based.
â?? Non-toxic & smokeless.
Environmentally friendly.
Can be applied well on steel construction body, steel bar, and steel sheet. Does not blister and get damaged when burning.
Rust removal is not required when applying CP-358W2K (unless the rust is thick).
Applications
Can be used in rocket missile or products that high-temperature application is required. Heating pipe.
Iron plate or sheet.
Indoor/outdoor fireproof paint.
Multiple iron materials/fireproof paint.
Plywood, veneer board.
Fire door surface treatment.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Supplier: 1. coco peat (coir pith), coir rugs,
2. textile chemicals, polysols, binders, thickeners and many other
industrial chemicals,
3. sugar confectionary products like lollipop etc.
4. eco friendly, sugarcane and paper packaging products like coffee/tea cups, beverage cups all sizes, takeaway lunch boxes, straws, etc.
5. frozen indian snacks like samosa, patties, mix veggies, all kinds of indian snacks and frozen foods.
6. pvd coated sanitary ware like kitchen sinks, basins, railing, taps, and other furniture with elegant polishes of gold, rose gold, black, silver, multi color, champagne colour, etc in different textures.
7. dehydrated vegetable and fruit powders like, dehydrated garlic powder, ginger powder, chickoo powder, etc.
8. onions
9. all kinds of supermarket items
Services: Export and import
Buyer: Mct oil : grade e 7000, e7030, e6040
(best quality)
PE/PP Tarpaulin None welded width can reach 1.8-4.2 meters and welded width can reach 30 meters. Coating on one side or both sides. According to customers requirements, it is available to add UV inhibitors or fire retardant or others. Laminating all around and using pp rope to strengthen, with Al-eyelets or black corner
Supplier: Electrical materials, electrical equipments, lighting fixtures, plumbing materials, ac materials, it materials, ceiling materials, partition materials, painting materials, floor tiles, hardware materials, hand tools & power tools, garage tools, wooden & carpenter materials, batteries. medical equipment and medical consumable product and medical surgical equipment.
