Steel zinc plated with a side slice
Stud Bolts
Bolts And Nuts
Small stainless steel d ring, tie-downs, d rings, anchors
Please quote for the following wholesale product requirement -
Product Name: Repair Clamps
Specifications:
Bands
Nominal Pipe Size (Inch)
Pipes Material Type
Length (mm)
No. bolts
Single Band 2
HDPE
3500
150 2
3
DI
150
150
2
4
DI
1000
150
2
5
HDPE
1000
150
2
6
DI
200
200
3
Double Bands
8
DI
25
300
3*
1. SCOPE
This Specification specifies the requirements for the design, materials and in-service performance of mechanical stainless steel repair clamps for waterworks purposes.
This Specification is designated for applications involving rigid pipes, typically ductile iron (DI), grey cast iron (CI), and steel (S). Also, for applications involving flexible pipes, typically un-plasticized polyvinylchloride (PVC-U) and high-density polyethylene (HDPE).
All materials and Equipment shall be in every respect suitable for storage, installation, use and operation in the conditions of temperature, humidity and The PH and water quality appertaining in Jordan.
The atmospheric temperature in Jordan varies between -10 C and 50 C.
2. Application
Stainless steel repair clamps complying with this specification are intended for use in repair of water supply pipelines of the size designated in Table 1, with a maximum service temperature of 50°C and up to an allowable operating pressure of 16 bars for ranges diameter up to 250 mm and 10 bar for diameters larger than 250 mm. Repair clamps have limited ability to accommodate axial deflection and are, therefore, not generally intended for use as couplings to join tow pipes together. However, they are commonly utilized for repair situations at full pipe break, where the pipe ends are considered stable. In addition, repair clamps complying with this specification are intended to provide a permanent means of preventing loss from or contamination of pipelines that have been affected by corrosion or mechanical damage in both above-ground and buried applications.
3. Materials
The material of the Clamps shall be
Bands: Stainless Steel Grade AISI 304(A2) to BS1449:1991: part 2 or Grade AISI 316(A4) stainless steel to BS 1449:1991:part 2, for corrosion resistance.
Bolts shall be Stainless Steel A2, Teflon coated, or mild steel. Nuts & washers shall be Stainless Steel A2, or mild steel class 4.6 to BS EN20898: Part 1. Receiver bars shall be TIG- welded to shell to form strong fusion, and fully passivated after welding,
Gasket shall have a gridded pattern for positive sealing, and to be made of specially compounded NBR rubber specially formulated for water service or EPDM. Compound Grade E to BS2494:1990
4. Design
The Clamps shall be used for permanent repair of cracks, holes, or complete breakages of steel, ductile Iron, PVC and HDPE pipes.
The Clamps shall be suitable for potable water for Temperature range (-10 to 50) C. potable water certificate must be submitted .
Repair Clamps shall be standard full circle single band for diameter 150mm or less. And full circle double band for diameter more than 150mm, length and number of bolts not less than the values in Table 1 for each diameter.
Gasket shall provide a 360o sealing surface and of such size and shape to provide an adequate compressive force against the pipe after assembling to affect a positive seal under all combinations of joint and gasket tolerances. And heavy gauge Type 304 stainless Steel bridge plate shall be attached into the gasket end to span the lug area and to make installation quick and easy.
Bolt retainer assembly or lugs shall be of a type 304 stainless steel, and shall be MIG welded to receiver bar and fully passivated after welding. Lugs may be cast, forged or cold formed of type 304 stainless steel, and may include a high impact polycarbonate plastic, non corrosive retainer. Lug design shall
Quantity Required : MOQ
Shipping Terms : CFR
Destination Port : Aqaba, Jordan
Payment Terms : LC
Looking for suppliers from : Worldwide
Con
The buyer would like to receive quotations for -
Product Name: Suspension Clamp With Bracket
Specifications :
Accessories For Aluminum Self-supported Insulated Aerial Bundled Cable
Quantity
1.Accessories for aluminum self-supported insulated aerial bundled cable for attachment to poles complete
As follows:
1.1 Dead end clamp for 70 mm2 neutral messenger. No. 15000 Pcs
1.2 Suspension clamp with bracket
No. 6000 Pcs
Conductors for phases must be hard-drawn aluminum round compacted stranded with size of (120, 95&50) mm2 while street lighting conductor is 25 mm2.The neutral conductor must be of aluminum alloy (95,70&35) mm2. All cores are black (XLPE) weather and Ultra-Violet (UV) resistance insulated, in accordance to NFC Standard or equivalent.
Tension charts for the required types of cables should be submitted with the offer to cover the following design conditions:-
Cold area Hot area
Min. ambient temp............... Deg C -10 0
Every day temp.................... Deg C 20 25
Max. ambient temp............... Deg C 40 50
Wind Loading (over ice).......... (N/m2) 700 700
Ice loading (radial thickness)... (mm) 10 0
A factor of safety at min. temp. 2.5 2.5
The factor of safety at everyday temp. 5 5
The main dimensions of the low voltage twisted cable 0.6 / 1 kV
(3*120+25+70 (mm2, are as follows:)
-Main phase conductor = 120 mm2
-Construction = 19 wires- hard drawn aluminum round compacted stranded
-Insulation thickness = 1.8 mm-XLPE
-Lighting conductor construction = 25 mm2
-Construction = 7 wires - hard drawn aluminum round compacted stranded
-Insulation thickness = 1.4 mm - XLPE
-Neutral conductor construction = 70 mm2 AL Alloy
-Construction = 7 wires - Non compacted
- Insulation thickness = 1.6 mm XLPE
-Approximate Nominal overall diameter of cable = 45 mm
-Nominal weight of cable per meter =1.65 kg
Main phase and lighting conductors are twisted around neutral; breaking load:
120 mm2 phase conductor aluminum = 14 kN 25mm2 lighting conductor aluminum = 2.5kN 70 mm2 neutral aluminum alloy =20.6kN
Max. D.C. resistance at 200 C:
120 mm2 phase condominium =0.253 ohm/km 25 mm2 lighting conductor aluminum =1.2 ohm/km 70 mm2 neutral aluminum alloy =0.493 ohm/km
The main dimensions of the low voltage twisted cable 0.6 / 1 kV
(3*95+25+70 (mm2, are as follows:
-Main phase conductor = 95 mm2
-Construction = 19 wires- hard drawn aluminum round compacted stranded
-Insulation thickness = 1.8 mm-XLPE
-Lighting conductor construction = 25 mm2
-Construction = 7 wires – hard drawn aluminum round compacted stranded
-Insulation thickness = 1.4 mm - XLPE
-Neutral conductor construction = 70 mm2 AL Alloy
-Construction = 7- Non compacted
-Insulation thickness = 1.6 mm XLPE
-Approximate Nominal overall diameter of cable = 45 mm
-Nominal weight of cable per meter =1.357 kg
Main phase and lighting conductors are twisted around neutral; breaking load:
95 mm2 phase conductor aluminum = 14 kN 25mm2 lighting conductor aluminum = 2.5kN 70 mm2 neutral
-Lighting conductor construction = 25 mm2
-Construction = 7 wires – hard drawn aluminum round compacted stranded
-Insulation thickness = 1.4 mm - XLPE
-Neutral conductor construction = 70 mm2 AL Alloy
-Construction
Quantity Required : 21000 Piece/Pieces
Shipping Ter
Please provide a quotation to the following requirement from importer -
Product Name: Hardware Fittings
Specifications:
Nails, Screws & Fasteners. Brackets. Collated Nails. Braces.
Material standard
Worldwide Suppliers
Packaging Terms : Standard
Quantity Required : 1 Twenty-Foot Container
Shipping Terms : CIF
Destination Port : Amman, Jordan
Payment Terms : CAD
Looking for suppliers from : Worldwide
Contact : Amjad
Automotive parts: engine mounts, transmission mounts, rubber parts, bushings, autmotive bolts and nuts, suspension parts, brake parts, primarily for japanese vehicles
Pressure Washer
Fasteners like washers, bolts and nuts
Please quote for the following wholesale product requirement -
Product Name: DI Fittings
Specifications :
Item # Description QTY Unit
1 All Flange Tee 100 × 100 × 100 mm 16 Bar 200 Each
2 All Flange Tee 150 × 100 × 150 mm 16 Bar 50 Each
3 All Flange Tee 150 × 150 × 150 mm 16 Bar 10 Each
4 All Flange Tee 200 × 200 × 200 mm 16 Bar 10 Each
5 Ductile Double Flange Elbow 100mm 90 Degree 16 Bar 50 Each
6 Ductile Double Flange Elbow 100mm 45 Degree 16 Bar 65 Each
7 Ductile Socket Flange 150mm 16 Bar 15 Each
8 Ductile Socket Flange 200mm 16 Bar 15 Each
9 Universal Coupling Ductile 100mm 16 Bar 200 Each
10 Universal Coupling Ductile 150mm 16 Bar 100 Each
11 Universal Coupling Ductile 200mm 16 Bar 50 Each
12 Flange Adaptor Ductile 100mm 16 Bar 750 Each
13 Flange Adaptor Ductile 150mm 16 Bar 300 Each
14 Flange Adaptor Ductile 200mm 16 Bar 100 Each
15 Ductile Blank Flange 100 mm 16 Bar 200 Each
16 Ductile Blank Flange 150 mm 16 Bar 25 Each
17 Ductile Blank Flange 200 mm 16 Bar 20 Each
18 Ductile Reducer Flange 200 mm × 100mm 16 Bar 25 Each
19 Ductile Reducer Flange 200 mm × 150mm 16 Bar 25 Each
20 Ductile Tapping Saddle Clamp 100 × 25 mm 16 Bar 500 Each
21 Ductile Tapping Saddle Clamp 100 × 32 mm 16 Bar 600 Each
22 Ductile Tapping Saddle Clamp 150 × 25 mm 16 Bar 350 Each
23 Ductile Tapping Saddle Clamp 150 × 32 mm 16 Bar 250 Each
24 Ductile Tapping Saddle Clamp 150 × 63 mm 16 Bar 150 Each
1. General
1.1 Potable Water Certification
All fittings, gaskets and materials shall be certified for potable water use, and all pipes and materials should be certified as safe for transporting potable water by an independent testing laboratory. All material in contact with or likely to come into contact with water for public shall introduced with the requirements of BS 6920 (suitability for non metallic products for use in contact with drinking water) or any equivalent standard as well as the Jordanian standard (JS 286/2008) and the requirements of EN 15664 ( influence of metallic materials on water intended for human consumption ) or any equivalent standard and the World Health Organization standard (WHO), and whenever the regulation is changed it is the supplier responsibility to ensure conformity with any new requirements.
1.2 Toxic Materials
All fittings, coating, sealing and lining material shall be certified for potable water use and shall contain no ingredients that may migrate into water in amounts that are considered to be toxic or otherwise dangerous for health. Pipes and pipeline components, including their protective coatings and joint materials, that will or may come into contact with potable water shall not constitute a toxic hazard, shall not support microbial growth, shall not cause taste or odour, cloudiness or discolouration of the water and shall contain no ingredients that may migrate into water in amounts that are considered to be toxic or otherwise dangerous for health.
Non-toxicity certificate should be provided in English.
1.3 Third Party witness
The supplier/contractor shall furnish an original certificate from third party inspection agency showing all test results and analysis required by the applicable standard according to which the materials have been manufactured. The third party inspection agency shall under this contract, have witnessed the manufacture and testing operation to verify compliance with the technical specifications and the relevant standard. All certification should be from third party, and the certification should be valid and up to date, in English, and it must be shown in the certificate which batch is being tested to make sure that this certificate is for the right batch.
Quantity Required : MOQ
Shipping Terms : CFR
Destination Port : Aqaba, Jordan
Payment Terms : LC
Looking for suppliers from : Worldwide
Contact : Ramzi Saba
Please provide a quotation to the following requirement from importer -
Product Name: GI Fittings
Specifications :
Item Description Qty Unit
1 GI Coupling 1/2" Weldable 1,500 Ea (10pcs/Bag)
2 GI Coupling 3/4" Weldable 1,500 Ea (10pcs/Bag)
3 Weldable 1" Coupling GI 1,000 Ea (10pcs/Bag)
4 Weldable 2" Coupling GI 500 Ea (5pcs/Bag)
5 GI Union Joint 1/2" 200 Ea (10pcs/Bag)
6 GI Union Joint 3/4" 1,000 Ea (10pcs/Bag)
7 GI Union Joint 1" 1,000 Ea (10pcs/Bag)
8 GI Union Joint 2" 500 Ea (5pcs/Bag)
9 GI Nipple 1/2" 25,000 Ea (10pcs/Bag)
10 GI Nipple 3/4" 33,000 Ea (10pcs/Bag)
11 GI Nipple 1" 5,00 Ea (10pcs/Bag)
12 GI Nipple 2" 1,000 Ea (5pcs/Bag)
13 GI Reducer 3/4" x 1/2" 20,000 Ea (10pcs/Bag)
14 GI Reducer 1" x 1/2" 1,000 Ea (10pcs/Bag)
15 GI Reducer 1" x 3/4" 6,000 Ea (10pcs/Bag)
16 GI Reducer 2" x 3/4" 200 Ea (5pcs/Bag)
17 GI Reducer 2" x 1" 200 Ea (5pcs/Bag)
18 GI Tee 1/2" 200 Ea (10pcs/Bag)
19 GI Tee 3/4" 4,000 Ea (10pcs/Bag)
20 GI Tee 1" 500 Ea (10pcs/Bag)
21 GI Tee 2" 100 Ea (5pcs/Bag)
22 GI Tee Reducer 3/4" x 1/2" x 3/4" 4,000 Ea (10pcs/Bag)
23 GI Tee Reducer 1" x 1/2" x 1" 1,000 Ea (10pcs/Bag)
24 GI Cross 3/4" 500 Ea (10pcs/Bag)
25 GI Cross 1" 500 Ea (10pcs/Bag)
26 GI Elbow 1/2" 1000 Ea (10pcs/Bag)
27 GI Elbow 3/4" 15,000 Ea (10pcs/Bag)
28 GI Elbow 1" 3,500 Ea (10pcs/Bag)
29 GI Elbow 2" 500 Ea (5pcs/Bag)
30 GI Reducer Elbow 1" x 1/2" 100 Ea (10pcs/Bag)
31 GI Reducer Elbow 3/4" x 1/2" 250 Ea (10pcs/Bag)
32 GI plug 1/2" with a hole 4,500 Ea (10pcs/Bag)
33 GI plug 3/4" with a hole 1,000 Ea (10pcs/Bag)
34 GI plug 1" with a hole 1,000 Ea (10pcs/Bag)
35 GI plug 2" with a hole 500 Ea (5pcs/Bag)
Galvanized Iron Fittings specifications
1.1 Ambient Conditions
All Fittings, materials and Equipment shall be in every respect suitable for storage, installation, use and operation in the conditions of temperature, humidity and The PH and water quality appertaining in Jordan.
The atmospheric temperature in Jordan varies between -10°C and 50 °C.
1.2 Potable Water Certification
All Fittings and materials shall be certified for potable water use, and all fittings and materials should be certified as safe for transporting potable water by an independent testing laboratory. All material in contact with or likely to come into contact with water for public shall introduced with the requirements of BS 6920 (suitability for non metallic products for use in contact with drinking water) or any equivalent standard as well as the Jordanian standard (JS 286/2008) and the requirements of EN 15664 ( influence of metallic materials on water intended for human consumption ) or any equivalent standard and the World Health Organization standard (WHO), and whenever the regulation is changed it is the supplier responsibility to ensure conformity with any new requirements..
1.3 Toxic Materials
Fittings and components, including their protective coatings and joint materials, that will or may come into contact with potable water shall not constitute a toxic hazard, shall not support microbial growth, shall not cause taste or odour, cloudiness or discoloration of the water and shall contain no ingredients that may migrate into water in amounts that are considered to be toxic or otherwise dangerous for health Non toxicity certificate should be provided.
1.4 Third Party Witness
The supplier must submit at least 3 different international third party companies where Miyahuna will choose one of them.
The supplier shall furnish an original certificate from a third party inspection agency showing all test resu
Quantity Required : MOQ
Shipping Terms : CFR
Destination Port : Aqaba, Jordan
Payment Terms : LC
Looking for suppliers from : Worldwide
Contact : Ramzi Saba
Fastener, Stationery, Dewatering, Auto Parts, Bicycle & Spare Parts, Electrical Products, Construction Materials, Hand Tools, Medical Equipment, Safety Equipment, Solar System & Fitting, Inverter Batteries, Tiles, Tyre & Tubes, A4 Copy Paper, Packing Material, Plywood, Wood Laminate, Wooden Doors, Flush Doors
Please quote for the following wholesale product requirement -
Product Name: Nuts, Bolts
Specifications:
Type: Nuts, Bolts, Screws, Etc.
Material: Steel, Metal, Aluminum, Etc.
Size: Customize
Packaging Terms : Standard
Quantity Required : MOQ
Shipping Terms : Ex Works
Destination Port : Amman/ Aqaba, Jordan
Payment Terms : To be discussed with suppliers
Looking for suppliers from : Worldwide
Contact : Susan
Diesel fuel en590, gasoline 91/95 octane, crude oil, white kerosene oil, carbon steel pipes, stainless steel pipes, stainless steel fittings, carbon steel fittings, forged carbon steel fittings, forged stainless steel fittings, malleable iron fittings, galvanized malleable fittings, forged carbon steel flanges, forged stainless steel flanges, forged carbon steel valves, forged stainless valves, for electrical fittings rigid & pvc coated, for welding solutions, for industrial safety equipments, power tools, tools, consumables, valves, pipe tools tech, p.p.e, hoses, fasteners & fitting, gaskets, pipes, filters, hand tools, pvf, ups, control panel, pumps & motors , bearing & other industrial material.
Leather Bag, Leather Gloves, Leather Tools Bag, Cotton Wiping Rags, Duster Cloth, Cotton Clips, Cotton Waste
Hr Coils, Profiles(ipe Hea & Heb Equal Angles Upn) Heavy Plates And Deformed Bars
Fiberglass Cable Trays, Glass Fiber Filled Trefoil Clamps, Fiberglass Luminaries, Fiberglass Ladder, Fiberglass Light Poles, Junction Box, Distribution Board, Push Button Station & Switch Socket Outlet
