Brief Introduction of Wire Mesh Cable Tray Systems:
These are thicker and therefore stronger than apparently similar products. Cablofil incorporates a unique T welded safety edge resulting in performance comparable with traditional cable tray but with many added benefits.
Features and Benefits of Wire Mesh Cable Trays:
1. Electroplated Zinc Finish
2. Fast Easy Installation
3. Mesh Design Allows Cable Exit or Entry at any point
4. Clear Cable Identification
5. Supplied in 3 Metre Lengths
6. Significant Cost Savings Compared to Standard Tray Products
7. Simple Creation of Fittings on Site
8. Wide Range of Sizes
9. Heights Shown are Internal Dimensions
Manufacturing:
Optional Material for wire mesh cable tray: Black Steel, Stainless Steel, Aluminium, Alloy, Fibreglass Reinforced Plastic (FRP)
Mode: Top curved / Top Straight
Surface Finish: Zinc-plating, Hot-dip Galvanizing (HDG), Powder-coated, Pickled & Passivated.
Color: Optional
Suggestions:
1). MATERIAL
The choice of materials is a matter of the physical and mechanical properties produced by each, compared against the intended function, as well as the environment, in which the trays are to be installed.
2). SURFACE FINISH:
A). Zinc-plating cable trays are suitable for indoor use. The place where cold zinc-plating cable trays would work should be dry, ventilated, and corrosion free.
B). Hot-dip Galvanizing (HDG) cable trays are not suggested for wire mesh cable trays.
C). Powder-coated cable trays should be carried out in alkali and salt corrosion free site.
D). Pickled & Passivated should be used to stainless steel wire trays.
Specification for power and communications cabling containment.
1). SCOPE
Steel Wire Cable Tray conforming to the material and performance of this specification.
2). GENERAL
A). Cable tray shall be manufactured from steel wires, welded together and bent into final shape prior to surface treatment.
B). Surface Treatments:
i). Electro zinc plated to BSEN 12329-2000 for interior use (level 2)
ii). Hot Dipped Galvanised with between 60 and 80 microns of zinc to BS 729.
iii). Stainless Steel AFNOREZ CND 17.2 (AISI 316L)
C). Steel Wire Cable Tray Widths & Depths
i). Cable Tray dimensions are all internal.
ii). Depths of 30mm, 54mm, 80mm, 105mm & 150mm
iii). Widths of 50mm, 100mm, 150mm, 200mm, 300mm, 400mm 450mm, 500mm & 600mm for depths of 30mm & 54mm.
iv). Widths of 100mm, 150mm, 200mm, 300mm 400mm & 500mm for Depths of 105mm & 150mm
All trays are of 3005mm long
3). SPECIFICATION
a). Steel Wire Cable Tray will be produced from lateral and longitudinal sidewall steel wires, with minimum diameters of -:
4 mm for trays of widths up to 150mm
4.5 mm for trays of widths of 200mm
5.0 mm for trays of widths of 300mm
6.0 mm for trays of widths of 400mm, 450mm, 500mm and 600mm
b). Trays will be manufactured with a longitudinal 'T-welded' safety edge along the top wire of the sidewall (excluding CF3050)
c). Trays will be constructed with a 50mm x 100mm mesh configuration.
d). All tray fittings (e.g. changes in direction, level and size) shall be constructed on site, to the manufacturers instructions, using side action bolt croppers and fastened using 25mm and 30mm counter clamps with M6 bolts and nuts, all surface treated as the tray.
e). Trays will be coupled together using either a fast spring coupler or a 25mm/30mm counter clamp combination with supporting lateral splice plate on trays over 300mm width. The coupling will have the same surface finish as the tray.
f). Trays shall be supported at a maximum span of 2.5m by trapeze, wall, floor or channel mounting methods and will not exceed maximum loads as specified by the manufacturer.
g). All welds will be manufactured to an average minimum tensile strength of 500Kg per weld.
4. TESTS, CERTIFICATION AND CONFORMITY
a). Loading and deflection characteristics of the tray should be tested and the results published in accordance with the European Standard CEI/61537.
b). Suitability for the support of Cat6 data cabling should be demonstrated by way of independent test verification.
c). Fire test certification should be published in accordance with the E30/E90 standard.
d). Electrical continuity across a coupling should be demonstrated by means of a published test method and result.
We are able to design styles in various specifications according to the drawings and/or samples by the clients. And we offer fair price, excellent quality, quick delivery, continuous improvement. We own customer satisfaction. You can trust on us that we are the leading manufacturer of cable trays.
Wire Mesh Cable Tray provides
A job site, field adaptable support system primarily for low voltage, telecommunication and fiber optic cables. These systems are typically steel wire mesh, zinc plated.
standard widths of 2, 4, 6, 8, 12, 16, 18, 20, and 24 inches
standard depths of 1, 2, and 4 inches
standard length of about 10 feet (118)
Wire Mesh tray is generally used for telecommunication and fiber optic applications and are installed on short support spans, 4 to 8 feet.
Material:
Q235B Steel (Chinese standard steel), SS304, SS316 & SS316L
Surface Finish:
Electro zinc plated ¨C for indoor use to BS EN 12329-2000, 12microns thick.
Powder coated - for indoor use to JG/T3045-1998, between 6 and 10 microns thick
Hot Dipped Galvanized ¨C for outdoor use to BS EN 1461-1999, between 60 and 80 microns thick
Electrolytic Polishing ¨C for stainless steel use
Specification:
Model D W L WEIGHT
WB1.5X4X10 1.5'' 4'' 10' 5.8lbs
WB1.5X6X10 1.5'' 6'' 10' 7.4lbs
WB1.5X8X10 1.5'' 8'' 10' 9lbs
The advantages of our wire mesh cable tray:
1. Low cost, significant cost savings compared to standard traditional tray products.
2. Light in weight, wide range of sizes.
3. Fast heat dispersion.
4. Strong enough to withstand short circuits. Provides strength, rigidity without additional hardware
5. Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs.
6. Flexible, easy and fast installation. Design allows cable exit or entry at any point.
7. Cables can be secured to clamps or ties.
8. Various hardware accessories available to fix, support and install.
9. Safe smooth edge design to protect cable
10. Easy for line check and cleaning , easy maintained.
All sharp ends are cut off to protect cables. Weight loading capacity is 27% stronger than traditional cable trays and cable ladders.
Application:
The electric cable tray system are widely used for construction projects, such as layingelectrical wire and cable. Making the lay of the electric wire, electric cable andpipeline achieved the universalized level.
Installation Notice:
Bends, Risers, T Junctions, Crosses & Reducers can be made from wire mesh cable tray straight sections flexibly in projects.
Trays shall be supported at a maximum span of 2.5m by trapeze, wall, floor or channel mounting methods and will not exceed maximum loads as specified by the manufacturer.
Wire Mesh Cable Tray systems can be safely employed in places where the temperature ranges between -40C and +150C without any change to their characteristics.
Our Quality IBC liner steel cage WIRE MESH FOR IBC TANK FRAME are great steel cage mesh for IBC Frame for use in Hotels, Garment Shops, Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Food & Beverage Factory, Farms, Restaurant, Home Use, Retail, Food Shop, Printing Shops, Construction works , Energy & Mining, Food & Beverage Shops, Other, Advertising Company.
The Core Components Includes PLC, Engine, Bearing, Gearbox, Motor, Pressure vessel, Gear, Pump
The KARAM PN-44 Full Body Harness is a safety harness designed for workers performing at heights. It features adjustable straps for a secure and comfortable fit, and is made with durable materials for long-lasting use. It also has multiple attachment points for tools and equipment, making it ideal for a variety of job sites and applications. The harness is tested and certified to meet industry standards, providing peace of mind and ensuring the safety of workers while they work at heights.
Our safety harnesses are designed for maximum protection and comfort in construction, industrial, and high-altitude work. Made from durable, high-strength materials, they ensure secure fall protection and compliance with safety standards.
we are able to offer a superior quality range of Reinforcement Mesh. All our products are available in various sizes, designs, and shapes at market leading prices to meet the demands of customers.
Floating cable which can be applied to underwater robot equipment, either in fresh water environment or in seawater environment. It is widely used in marine exploration robot, underwater ROV UAV remote control submersible, underwater camera, underwater construction, underwater search and rescue robot, pipeline detection robot, submersible pump and the link between various underwater electrical equipment and shore based equipment; Link of signal transmission, power supply and equipment control system from underwater to water.
103567 Wire Mesh Cable Tray Suppliers
Short on time? Let Wire Mesh Cable Tray sellers contact you.
