V6 FMC
V6 STD. FMC
V4 FMC
V6 STD NRS
V6 Fully SS
V6 3PCS. URC
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V6 Borewell Submersible Pumpset Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Description by Manufacturer ENGINE Engine Type V6 Bore x Stroke 3.63 x 3.00 in. (921 x 762 mm) Displacement 186 CID (3,046 cc) DIMENSIONS Shaft Length 25 in. (635 mm) Weight 528 lb. (240 kg) GENERAL Propshaft Horsepower 175 HP (131 kW) Full Throttle Operating Range 5000-6000 RPM Gear Ratio / Shift F-N-R Cooling Water-cooled with thermostat & pressure-controlled The Mercury Diesel Outboard is a diesel two-stroke designed for light duty commercial patrol boat applications. The EPA certified engine joins the U.S. Department of Defense spec diesel outboard Mercury Marine released in May 2015. The Mercury Diesel Outboard features exclusive spark ignition, direct fuel injected 2-stroke technology which enables it to run on readily available ultra-low sulfur diesel fuel. SPECIFICATIONS HP: 175 HP (131 kW) Engine type: V6 Displacement: 186 CID (3,046 cc) Displacement: 3.0 L Full throttle: 5000-6000 RPM Shaft length: 25 in. (635 mm) Gearcase ratio: 2.08:1 Dry weight *Lightest model available: 528 lbs (240 kg) Bore and stroke: 3.63 x 3.00 in (921 x 762 mm) Fuel system: 2-stage Direct Fuel Injection (DFI) Cooling system: Water-cooled with thermostat & pressure-controlled Gear shift: F-N-R Exhaust system: Through prop KEY FEATURES Available with a 25â?? (635 mm) center section and the 2:1 Fleet Master gearcase in both right-hand and left-hand rotation. Industry-exclusive spark ignition diesel engine. Glow plug ensures consistent, reliable cold starting. Commercial patrol boat models meet EPA emissions standards. Cylinder heads designed specifically for combusting diesel fuel. High performance cylinder liners for maximum horsepower and optimal engine running quality. Fuel/air mixture is injected into the combustion chamber at 95 psi for enhanced high rpm running quality.
Features may include: Powering Your Boat from 115 H.O. to 300 HP E-TEC G2 Best In Class fuel economy E-TEC Direct Injection Fuel Technology V6 from 150 H.O. to 300 HP Power Steering Available in white or gray, plus color panels Engine Engine Type V6 66 E-TEC G2 D.I. Bore 3.39 in (86 mm) Stroke 3.10 in (78.7 mm) Displacement 167 Cu in (2.7 cc) Throttle 5000-6000 RPM Gear Ratio (Primary) 2.17:1 Steering Tie Bar/Remote Electric Starter Electric Alternator 133 Amps Total / 50 net Dedicated / 14 amps @ idle Fuel System Fuel System E-TEC Direct Injection with stratified low RPM combustion mode Dimensions Length Shaft: 25 in (635 mm) Weights Weight 512 lbs (233 kg) Features Features Controls: Slate Gray
V9-V10 Borewell Submersible Pumpset Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series. - FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in Mix flow series. - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set. - Dynamically balanced rotating parts ensures minimum vibration and longer life. - Designed for wide voltage fluctuations. - Motor portion covered with corrosive resistance Stainless steel (SS 304) shell. - More durability and hygiene & High operating efficiency. - Specially designed thrust bearing to withstand high axial thrust load. - Extremely hardwearing water lubricated bearing. - Thread type motor construction ensures service feasibility. - Designed for wide voltage operation. - Best alternative for JET & Compressor pump set. - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 55 kW to 112 kW (75 HP to 150HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2900 RPM - Head Range : 12 mtr. To 300 mtr. - Discharge Range : 3600 LPM to 960 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Maximum Starts Per Hour : 10 Times
Power: 85-132vac/170-264vac 47-63hz Fuel tank capacity: 2.5l Test tube capacity: 120cc Ultrasonic wave frequency: 38-39khz Ultrasonic wave power: 100w Rotate speed: 0-9975r/min, step: 25r/min Pulse width: 0-30ms, step: 0.1ms Count: 0-9975r, step: 25r Time: 0-9975s, step: 5s System pressure: 0-6.2kg/c©o (variable regulated£© System flow: 4l/min Test cylinder: 6 (max) Dimensions: 400mm ¡á 510mm ¡á 450mm Weight: 25kg
V6 S.S. Submersible Pumpset
V6 Slim Submersible Pumpset MOTOR: Motor Shaft : AISI 410 / AISI 420, Thrust Bearing : Carbon Plate With S.S. Segment (With Tilted Pads), Stamping : Electric Sheet, Casting Parts : Graded Casting, Copper : E.C. Grade Copper (99.9% Purity), Bush : Leaded Tin Bronze (LTB-4), Fastners : Stainless Steel, Rubber Parts : NBR PUMP: Pump Shaft : AISI 410, Impeller : SS 304 , Diffuser : SS 304, Casting Parts: Graded Casting Technical Details: Head Range : Up To 400 Mtrs, Discharge Range : Up TO 560 lpm, Delivery : 50 mm, Power Rating : 4 H.P. TO 15 H.P., Voltage Range : 350 V TO 440 V (3-Phase) Salient Features: All Running Pumpsets Are Approved by B.I.S. & BEE, An ISO 9001-2015 Certified Company, Highly Efficient Motor & Pump, Specially Design For Wide Voltage Range, Easy To Install, Low Power Consumption, Corrosion Resistance Stainless Steel Motor & Pump Body, Rotors Are Dynamically Balanced 2850+ RPM TO Reduce Vibration, Long Life And Negligible Maintenance Due To High Precision Work, Rotor Are Painted With Special Epoxy Paint For Prevent Corrosion Effect For Long Time, Noiseless & Vibration Free Motors, All Parts Machined On CNC Machine Only, Easy To Rewind & Easily Repairable
V6 Submerible Pumpset (Fabricated Pump with Nema Standard)
V6 Submerible Pumpset (Fabricated Pump with Nema Standerd))
We Manufacture V6 Submersible Pumps From 3H.P To 30H.P
The Hammer Union can be used for cementing trucks, all kinds of manifolds and other high pressure equipment, and pipes. It is an important part for transporting oil. Water, fracturing fluid and mixed fluid. These products are all made of high quality steel by forging and finishing cut. They have good. Mechanical performance and sealing property. Especially they can operate under the bad weather condition. They can be assembled fixed easily and conveniently. Main technical parameter model number collecting norm working pressure, structural length drift diameter. The product adopts some end connections of pipeline thread, tubing thread, butt-weld.
Acoustic guitar 6pcs/ctn
V6 C.I. Diffuser & Nylon Impeller 50 Feet Submersible Pumpset
