Ultra Super Fine Grade of Quartz Silica Powder of High Purity inherently Inert, White Bright White Powder Form having Uniform Particle Size . 1. CHEMICAL SPECIFICATIONS 1. SiO2 : 99.00 ++ Minimum 2. Fe2O3 : 0.08% 3. Al2O3 : 0.01% 4. CaO : 0.02% 5. MgO : NIL 6. L.O.I. : 0.16 at 900* for 45 minutes 7. Oil Absorption : 27 ml/100gm to 35 ml/100gm 8. Water Absorption : 35 ml/100 gm 9. Bulk Density : 0.65 gm/cc Tapped 10. Brightness : 90% ++ minimum 2. PARTICLE SIZE ANALYSIS [MALVERN] 1. D - 50 : 3.00 microns 2. D - 90 : 6.99 microns 3. D - 97 : 9.59 microns 4. D - 98 : 10.40 microns 3. Refractive Index : 1.55 4. Specific Gravity : 2.56 5. Yellowness Index : 1.6 6. Reflectance : 94.50% 7. pH of 10% : 8 8. Hardness : 7 mohs 9. Melting Point : 1600*c 10. Boiling Point : 2230*c
NANOSIL Silica is a grade name of Silica series, manufactured by Nanotec India. NANOSIL is high purity of more than 99% of SiO2 natural crystalline silica. This micronized AND Jet Milled ground silica is inherently bright, white, low in moisture & inert by nature and the hardness of silica mineral yields improved burnish resistance and durability. Other important properties of this silica mineral include low resin demand, anti-foaming properties and sheen control. It is used in paints, industrial Cement flooring, Epoxy flooring etc. NANOSIL SILICA has Good Matting Effect, Narrow Particle Size Distribution, No Melting Point (thermoset), Temperature Resistant up to 200 °C, Highly Transparent in Film, High Scratch Resistance, High Resistance to Polishing, Shear Resistant, Chemical Resistant, No Swelling in Normal Coatings Solvents, No Adverse Effects on Catalysts, Little Influence on Viscosity/Rheology and Good Gloss Retention in All Weather. NANOSIL 1590 has Average Particle Size (D-50) is 3.5 microns and Top Cut (D-97) is 15 microns. Brightness is more than 90%.
NANOSIL Silica is a grade name of Silica series, manufactured by Nanotec India. NANOSIL is high purity of more than 99% of SiO2 natural crystalline silica. This micronized AND Jet Milled ground silica is inherently bright, white, low in moisture & inert by nature and the hardness of silica mineral yields improved burnish resistance and durability. Other important properties of this silica mineral include low resin demand, anti-foaming properties and sheen control. It is used in paints, industrial Cement flooring, Epoxy flooring etc. NANOSIL SILICA has Good Matting Effect, Narrow Particle Size Distribution, No Melting Point (thermoset), Temperature Resistant up to 200 °C, Highly Transparent in Film, High Scratch Resistance, High Resistance to Polishing, Shear Resistant, Chemical Resistant, No Swelling in Normal Coatings Solvents, No Adverse Effects on Catalysts, Little Influence on Viscosity/Rheology and Good Gloss Retention in All Weather. NANOSIL 0790 has Average Particle Size (D-50) is 1.8 microns and Top Cut (D-97) is 7 microns. Brightness is more than 90%.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
NANOTAL 530 is a high purity mineral composed of hydrated magnesium silicate originating with exceptional high brightness from the world best reserves in India. Talc is the world softest and most hydrophobic mineral insoluble and inert. It adds new features to products and makes processes more efficient. The performance of TALC products depends on its particle shape (aspect ratio) and particle size distribution. Our product portfolio offers a wide range of milling characteristics, including a narrow particle spectrum and efficient PSD curves. A variety of applications ranging from Paper, Paints, Polyester Putties, Plastics, Adhesives, Cosmetics, Ceramics and many more is being catered by NANOTEC INDIA product range. Our products are from the purest reserves with controlled residue resulting in some diversely crafted products with precisely controlled particle size distribution for high tech applications under brand name NANOTAL having good barrier properties, reinforcement property, scrub property, gloss, non-yellowing property, corrosion and coverage. Ultrafine NANOTAL provides enhanced reinforcement properties in rubber / elastomer applications. NANOTAL lamellar particles create an impermeable barrier, substantially reducing air and liquid transmissions. AR Talc also diminishes plasticizer evaporation, resulting in good thermal and weathering resistance, there by extending service life and imparts excellent barrier properties. NANOTAL is reinforcing filler and a processing aid in rubber applications and is particularly suited to high impermeability applications. NANOTAL has the ability to absorb moisture, absorb oils, absorb odor, serve as a lubricant and produce a feel good effect in human skin. Finely ground talc is also used as the powder base of many cosmetic formulations. The tiny platelets of a talc powder readily adhere to the skin but can be washed off easily. NANOTAL softness allows it to be applied and removed without causing skin abrasion. Naturally occurring hydrophobic, platy structured mineral improves reinforcement & stiffness to the end product. Further being chemically inert powder, helps to improve water resistance, chemical resistance and general weatherability. Talc increase the non-Thixotropic viscosity, betters resistance to cracks, dimensional stability and shrink resistance in epoxy sealant, joint compound & automotive putties. Talc being an inert material is exhibiting enormously less reactivity compared to the other fillers. It is used in agriculture as a barrier against the minute particles and dust further also act as a carrier in the feed premixes and agricultural chemicals like pesticides. An ultrafine series of NANOTAL is recommended for seed coating to form a uniform micro layer over the seed grains to overcome the problem of moisture formation & disallows premature germination.
Each paint is designed with specific attributes in mind, and Nanosil Series Silica is one of the ingredients that allows for each specificity. Nanosil Series Silica functions in paints and coatings as a great low-cost extender. As in other applications, Nanosil Series Silica is desirable for its chemical inertness which allows for good acid, chemical, and heat resistance. In marine and maintenance coatings, the durability of Nanosil Series Silica imparts excellent abrasion and corrosion resistance. 1. Nanosil Silica’s low oil absorption allows increased pigment loading for improved finish color. 2. Along with its chemical inertness, Nanosil Silica's hardness improves abrasion resistance in paints. 3. Paint formulators select micron-sized industrial sands to improve the appearance and durability of architectural and industrial paint and coatings. 4. In architectural paints, Nanosil Silica fillers improve tint retention durability, and resistance to dirt, mildew, cracking and weathering. 5. Nanosil Silica’s low oil absorption allows increased pigment loading for improved finish color. 6. In marine and maintenance coatings, the durability of Nanosil Silica imparts excellent abrasion and corrosion resistance. 7. Nanosil Silica improves the most important qualities in paints such as reflectance, brightness and color consistency for any large scale uses. Industrial sand, therefore, plays a role in keeping the buildings, cars, and boats we see from looking worn or dingy.
Ultra Fine Copper Powder Isotopes greater than 99.9998% purity
We deals in the following Chemicals :- Quartz / Silica Powder, Quartz / Silica Lumps, Quartz / Silica Granules, Quartz / Silica Grits Bentonite Powder, Bentonite Lumps, Bentonite Granules, Bentonite Clay Mica Powder, Mica Flakes, Mica Blocks, Mica Sheets, Mica Scraps Dolomite Powder Barite Powder, Barite Ore Hematite / Iron Oxide Powder, Iron Oxide ( Ferric Oxide ) Ilmenite (Synthetic Rutile) Fly Ash Powder Alumina Silica ( Cenosphere ) Powder Calcium Carbonate Powder Magnetite, Cellulose Fibers, Cellophane Flakes, Walnut Shells
We offer Ultra Fine Copper Powder with the purity of 99,9998% Isotopic composition : - 63Cu : 69,1% �± 0,05% - 65 Cu : 30,1% �± 0,05% Size : 5�µm - 15�µm Quantity : 4000 kg Certificate of Analysis : available from IGAS Research Methode : Scanning Electron Microscope ================================================================= OTHERS PRODUCTS ================================================================= Metals & Non-Ferrous : - Copper Cathodes - Copper Powder - Thermal Coal - Gold - Nickel - Iron Pipes - Cobalt Agricultural : - Cocoa - Coffee - Arabic Gum - Black Pepper
Construction
Constructure
As a general rule, The purer the sand, the clearer the products Silicon and oxygen are the earth's two most abundant elements and together they make silica, one of the earths three most common rock forming minerals. Akshar Minerals Silica sand is high purity natural crystalline silica. It is inherently bright, white, low in moisture and chemically inert in nature. Basically, It is made up of two main element Silica & Oxygen. Silica sand is made up of Silicon Dioxide. There are number of different uses of silica sand in the industrial and commercial sector, from golf courses to glass making . The chemical formula of Silica Sand is SiO2 Characteristics : High Purity Weather Resistant White Appearance Naturally Hard Controlled Particle size Chemically Inert Applications Akshar Minerals Silica sand is used depends on physical, chemical and mechanical characteristics such as grain size, shape color, structure and distribution as well as refractoriness strength and stability. There characteristics can differ depending on how mineral is processed after it is mined. This product gets easily mixed and can be used for high temperature applications like flat glass, furnace tubes and many more due to its excellent thermal expansion, hardness. It yields improved durability and burnish resistance. We make for all type of application in the industries like Glass industries, Sodium Silicate Industry, Golf course & Sport Ground, Adhesive and sealant, Rubber industry, Texture Wall Paint, Sand Blasting, Agro pesticide, Cosmetic industry, Soap & Detergent, Filtration Media, Power Plant & Petroleum, Construction Chemical Industry, Plastic, Fertilizer, Paint, Ceramic, Insulation, Foundry, Ramming Mass, Steel Industry, Landscaping, GRC & GRP Industry, Oil & Petroleum Industry, Oil Exploration & Oil Drilling.