HTF launched SOA series optical amplifier products can be 1290nm ~1320nm wavelength range to achieve amplification. It can be easily used in 100G transmission system, the maximum can support 160G/s rate. SOA optical amplifier can be used for booster amplification, pre-amplification and other occasions. O-band optical signal overall amplification Covering the wavelength range of 1290 ~ 1320nm 100G 1310nm signal amplification Support O-band, 1290 ~ 1320nm band amplification Output power up to 10dBm 100G 1310nm signal amplification Support APC Low noise, high gain One board supports up to 2 channels of signal amplification
The Semiconductor Optical Amplifier Devices at 1310nm and 1550nm are designed by using a high quality angled SOA chip and a TEC which can assure a stable amplified output for a large dynamic input signal. The devices are available in a standard, 14-pin butterfly package at the 1310nm and 1550nm bands. The SOA devices have high optical gain, high saturation output power, low polarization dependent loss, low noise figure and broad wavelength range. We have options of optical isolators for input and/or output side as well as output fibers of SM fibers, PM fibers and other special fibers per customer specifications. The products are Telcordia GR-468 qualified, and in compliance with RoHS requirement.
We are an EU approved CE certified, REACH Certified and RoHS Certified company manufacturer of Optical Brighteners OBA 220 for Paper Industry. We all want our papers to be as white as possible, don't we? Well, that's where optical brightening agents BBU Powder come in. The raw material of paper often consists of impurities such as snippets of bamboo sticks and wood. These impurities dampen the brightness of the paper. We have various Whitening Agent Optical Brightener Available for Paper application like... Optical Brightening Agent OBA 220 in powder form Optical Brightening Agent OBA 220 in Liquid form Optical Brightening Agent OBA 264 in Liquid form Optical Brightening Agent OBA 24 in powder form Optical Brightening Agent OBA 253 in Liquid form Optical Brightening Agent OBA 28 in powder form Optical Brightening Agent OBA 154 in Liquid form Optical Brightening Agent OBA 28 in powder form. Additional Information Physical Appearance : Greenish-Yellow Powder CAS No.: 16470-24-9 EINECS No.: 240-521-2 Specific Gravity / Bulk Density : 0.8-1.0 pH of Liquid or 1% Solution : 8-9 Strength by 100% : 100% Shade/Hue: Bluish white Whiteness/ Brightness : Equal to Std % of Active Substance : 21.95% Absorbance (18mg/l) : 0.217 Moisture Content : 2.40%
We are an EU approved CE certified, REACH Certified and RoHS Certified company manufacturer of Optical Brighteners OBA 220 for Paper Industry. We all want our papers to be as white as possible, don't we? Well, that's where optical brightening agents BBU Powder come in. The raw material of paper often consists of impurities such as snippets of bamboo sticks and wood. These impurities dampen the brightness of the paper. We have various Whitening Agent Optical Brightener Available for Paper application like... Optical Brightening Agent OBA 220 in powder form Optical Brightening Agent OBA 220 in Liquid form Optical Brightening Agent OBA 264 in Liquid form Optical Brightening Agent OBA 24 in powder form Optical Brightening Agent OBA 253 in Liquid form Optical Brightening Agent OBA 28 in powder form Optical Brightening Agent OBA 154 in Liquid form Optical Brightening Agent OBA 28 in powder form. Additional Information Physical Appearance : Greenish-Yellow Powder CAS No.: 16470-24-9 EINECS No.: 240-521-2 Specific Gravity / Bulk Density : 0.8-1.0 pH of Liquid or 1% Solution : 8-9 Strength by 100% : 100% Shade/Hue: Bluish white Whiteness/ Brightness : Equal to Std % of Active Substance : 21.95% Absorbance (18mg/l) : 0.217 Moisture Content : 2.40%
Fiber Optic Patch Codes
Fiber Optic Cables
We are an EU approved CE certified, REACH Certified and RoHS Certified company manufacturer of Optical Brighteners OBA 220 for Paper Industry. We all want our papers to be as white as possible, don't we? Well, that's where optical brightening agents BBU Powder come in. The raw material of paper often consists of impurities such as snippets of bamboo sticks and wood. These impurities dampen the brightness of the paper. We have various Whitening Agent Optical Brightener Available for Paper application like... Optical Brightening Agent OBA 220 in powder form Optical Brightening Agent OBA 220 in Liquid form Optical Brightening Agent OBA 264 in Liquid form Optical Brightening Agent OBA 24 in powder form Optical Brightening Agent OBA 253 in Liquid form Optical Brightening Agent OBA 28 in powder form Optical Brightening Agent OBA 154 in Liquid form Optical Brightening Agent OBA 28 in powder form. Additional Information Physical Appearance : Greenish-Yellow Powder CAS No.: 16470-24-9 EINECS No.: 240-521-2 Specific Gravity / Bulk Density : 0.8-1.0 pH of Liquid or 1% Solution : 8-9 Strength by 100% : 100% Shade/Hue: Bluish white Whiteness/ Brightness : Equal to Std % of Active Substance : 21.95% Absorbance (18mg/l) : 0.217 Moisture Content : 2.40%
BrightOmni UP is a Disulpho type Fluorescent Whitening Agent with high affinity for Paper in wet end applications to achieve high whiteness and brightness properties of Paper. It Can be added either batch wise in the mixing chest or continuously at suitable dosing points in the stock preparation system. It Should be applied prior to either alum or cationic auxiliaries. Typical average dosage is 2 - 6 kg/Ton of dry pulp depending on: - Type of furnish - Base pulp pH and brightness - Desired brightness and whiteness gain
Properties 1. Excellent transparency, outstanding resistance to aging. 2. It has good insulating properties and mechanical strength; to acid, alkali, salt has a strong resistance to corrosion; and because easy processing. Applications 1.Extruded sheets for signage, displays and building material 2.Motive parts such as tail lamps, meter covers and sun visors 3.General sundries such as tableware, kitchenware, giftware and bathroom accessories 4.Optical lenses such as sunglasses, reading glasses and camera lenses 5.Light guide panels for LCD displays 6.Other applications such as mobile phone display panels, clock covers, lighting covers/accessories, optical fibres, toys, etc.
EDFA Optical Amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). Integrated VOA can be automatically adjusted to achieve smooth gain spectrum. It can amplify the C-Band signal with or w/o middle stage access (MSA), which brings great flexibility for the network application. FUNCTIONï¼? C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1565nm Support systems to achieve different cross-section radio repeater transmission HIGHTLIGHT: Wide operating wavelength range:1528nm~1565nm Three Optical Amplifier C-Band applications: Booster , In-line, Pre-amplifier Low noise figure: typical: 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Many model options serve all the traditional amplifier applications in an extended optical link: booster, in-line, and pre-amplifier. A booster amplifier operates at the transmission side of the link. It features high input power, high output power, and medium optical Gain . Boosters are designed to amplify aggregated optical input power for reach extension. An in-line amplifier operates in the middle of an optical link. It features medium to low input power, high output power, high optical Gain , and a low noise figure. In-line amplifiers are designed for optical amplification between two network nodes on the main optical link. A Pre-amplifier operates at the receiving end of an optical link. It features medium to low input power, medium output power, and medium Gain. Pre-amplifiers are designed for optical amplification to compensate for losses in a demultiplexer located near the optical receiver. Some EDFA Models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility. New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
Products including: optical network equipment, x2,xenpak,qsfp,sfp,sfp+,csfp,cfp2,copper qsfp, cwdm dwdm mux,demux, 10gpon olt sfp, computer networking, networking transcievers, data center, active optical fiber; direct attach cable, fttx; sdh; ethernet;fiber channel;lte, edfa, soa optical amplifier, media converter, and optical test equipments.
EDFA Optical Amplifier 1U Rack EDFA is the erbium-doped fiber amplification board. Its main function is to compensate the power of the signal optical in the transmission line, and it can amplify the optical signals of up to 48 channels with 100 GHZs interval) or 96 channels with 50 GHZ s interval) at C band at the same time. It has characters of flat gain, locked gain, low noise index, etc. It's an indispensable and important component for DWDM system, future high speed system and all-optical network long-distance transmission.
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units . Wide operating wavelength range:1528nm~1565nm Dual amplifier contains two independent gain units Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units . Wide operating wavelength range:1528nm~1565nm Dual amplifier contains two independent gain units Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR
Single Fiber Bidirectional EDFA Amplifier models include a Red and a blue port designed for single fiber DWDM Solution. The design of these models is used for single-fiber DWDM transmission systems. C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1561nm Support systems to achieve different cross-section radio repeater transmission Operating wavelength range: Blue: 1528nm~1543nm Red: 1547nm~1561nm Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Offset the insertion loss introduced by DCM Reduce the additional degradation of system OSNR Flexible insertion of DCMs at different distances Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Single fiber bidirectional EDFA amplifier include an Red and blue port, Red optical amplifier include an blue out port and blue in port, Red optical amplifier Amplify red optical signal, blue out port and blue in port are used to access the amplifier to amplify the blue optical signal. Blue optical amplifier include an red out port and red in port, Blue optical amplifier Amplify blue optical signal, red out port and red in port are used to access the amplifier to amplify the red optical signal, Blue: 1528nm~1543nm. Red: 1547nm~1561nm.
Domestic wire, house wire, submersible cables (flat / round), single core flexible cable, multi core flexible cable, xlpe insulated pvc sheathed power cable, xlpe insulated armoured control cable, pvc insulated armoured control cable, xlpe insulated unarmoured control cable, pvc insulated unarmoured control cable, optical fiber cable, optical fiber armoured cable, ftth drop cable, instrumentation cable, shielded cable. networking cable, cat 6 cable, cat 6 utp cable, cat 6 stp cable, cat 6 sftp cable, cat 6 ftp cable fire alarm cable, fire survival cable, data cable, electric cable, coaxial cable, cctv cable, travelling cable, lift cable, lift traveling cable.
CHF 19,03â??CHF 107,02 including VAT, excluding shipping Size 1 litre 5 litres 10 litres Very suitable for non-ferrous and precious metals, brass, nickel and titanium. The product is liquid, emulsifying, silicate and phosphate-free, mildly alkaline. It also removes greasy fingers and hand sweat Weight n/a Size 1l, 5l, 10l
DISULPHO GROUP PRODUCT NAME C.I. NO. AREA OF APPLICATION Bridgeo Milky White BA 267% Powder 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White SRK Powder 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White BHT-HC Powder 252 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White WHN-C Powder 113 Suitable at high temperature exhaust with H2O2 bleach for cotton, nylon, wool & silk Bridgeo Milky White WHN Powder 113 Suitable at high temperature exhaust with H2O2 bleach for cotton, nylon, wool & silk Bridgeo Milky White S Powder -- Tinted product for Exhaust at high temperature Bridgeo Milky White 4BB Powder 28 Tinted product for Exhaust at high temperature for cotton (terry-towel) & blend. Bridgeo Milky White BHT-HC Liquid 252 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White TG Liquid 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White BA Liquid 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White 4BK Powder 252 Suitable at high temperature exhaust with H2O2 bleach. TETRASULPHO GROUP Bridgeo Milky White BBU Powder 220 Padding & Exhaust at medium temperature Bridgeo Milky White 2B CONC Powder 24 Padding & Exhaust at medium temperature Bridgeo Milky White BVN CONC Powder -- Padding & Exhaust at medium temperature Bridgeo Milky White BVN CONC Powder (B) -- Padding & Exhaust at medium temperature Bridgeo Milky White 2B Powder 24 Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White 2BT Powder 28 Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White BVN Powder (BB Supra) -- Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White HI Powder -- Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White S Powder -- Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White UF-P Liquid 220 Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White ABIZ Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White API Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White ABP Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White SI Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White UBR Liquid 263 Padding & Exhaust at medium temperature HEXASULPHO GROUP Bridgeo Milky White AS Liquid -- Padding and exhaust at low temperature. Bridgeo Milky White HF Liquid (UF AS LIQ) -- Padding and exhaust at low temperature. Bridgeo Milky White BSU Liquid 264 Padding and exhaust at low temperature. Bridgeo Milky White AS Powder -- Suitable for Acid Cross Linking, Padding and exhaust at low temp, reddish tone
DISULPHO GROUP PRODUCT NAME C.I. NO. AREA OF APPLICATION REMARKS Bridgeo Milky White BA 267% Powder 113 Suitable for recycled pulp at wet end at alkaline pH. Bridgeo Milky White BMK Powder 113 Suitable for recycled pulp at wet end at alkaline pH. Bridgeo Milky White SRK Powder 252 Suitable for recycled pulp at wet end at alkaline pH. Bridgeo Milky White BHT-HC Powder 252 Suitable for recycled pulp at wet end at alkaline pH. Bridgeo Milky White BHT-HC Liquid 252 Suitable for recycled pulp at wet end at alkaline pH. Bridgeo Milky White UP-HC Liquid 113 Suitable for virgin and wood pulp at alkaline pH. Bridgeo Milky White UP Liquid 113 Suitable for virgin and wood pulp at alkaline pH. Bridgeo Milky White UF-UP Liquid 113 Suitable for virgin and wood pulp at alkaline pH. Urea & Salt Free TETRASULPHO GROUP Bridgeo Milky White BBU Powder 220 Used in Waste Paper & Straw Pulp in acidic to neutral pH. Bridgeo Milky White ABP-X Powder 220 Mostly used in Waste Paper Pulp in acidic to neutral pH. Bridgeo Milky White UF-P Liquid 220 Mostly used in Pulp Board & Tissue in acidic to neutral pH. Urea & Salt Free Bridgeo Milky White ABIZ Liquid 220 Used in Tissue from Waste Paper in acidic to neutral pH. Bridgeo Milky White API Liquid 220 Used in newsprint from Waste Paper in acidic to neutral pH. Bridgeo Milky White ABP Liquid 220 Used in newsprint from Waste Paper in acidic to neutral pH. Bridgeo Milky White SI Liquid 220 Used in newsprint from Waste Paper in acidic to neutral pH. HEXASULPHO GROUP Bridgeo Milky White AS Liquid -- Used in Size Press & Coating, at any pH. Urea & Salt Free Bridgeo Milky White HF Liquid -- Used in Size Press & Coating, at any pH. Urea & Salt Free Bridgeo Milky White BSU Liquid 264 Used in Size Press & Coating, at any pH for extra bluish whiteness Urea & Salt Free Bridgeo Milky White MST Liquid 353 In Board Machine at Coating for reddish shade Urea & Salt Free Bridgeo Milky White BSUT Liquid 264 Used in Size Press & Coating for violetish blue shade Bridgeo Milky White AS Powder -- Used in Size Press & Coating.
DISULPHO GROUP PRODUCT NAME C.I. NO. AREA OF APPLICATION Bridgeo Milky White BA 267% Powder 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White SRK Powder 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White BHT-HC Powder 252 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White WHN-C Powder 113 Suitable at high temperature exhaust with H2O2 bleach for cotton, nylon, wool & silk Bridgeo Milky White WHN Powder 113 Suitable at high temperature exhaust with H2O2 bleach for cotton, nylon, wool & silk Bridgeo Milky White S Powder -- Tinted product for Exhaust at high temperature Bridgeo Milky White 4BB Powder 28 Tinted product for Exhaust at high temperature for cotton (terry-towel) & blend. Bridgeo Milky White BHT-HC Liquid 252 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White TG Liquid 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White BA Liquid 113 Suitable at high temperature exhaust with H2O2 bleach. Bridgeo Milky White 4BK Powder 252 Suitable at high temperature exhaust with H2O2 bleach TETRASULPHO GROUP Bridgeo Milky White BBU Powder 220 Padding & Exhaust at medium temperature Bridgeo Milky White 2B CONC Powder 24 Padding & Exhaust at medium temperature Bridgeo Milky White BVN CONC Powder -- Padding & Exhaust at medium temperature Bridgeo Milky White BVN CONC Powder (B) -- Padding & Exhaust at medium temperature Bridgeo Milky White 2B Powder 24 Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White 2BT Powder 28 Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White BVN Powder (BB Supra) -- Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White HI Powder -- Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White S Powder -- Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White UF-P Liquid 220 Bleaching with H2O2, padding and exhaust at medium temperature Bridgeo Milky White ABIZ Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White API Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White ABP Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White SI Liquid 220 Padding & Exhaust at medium temperature Bridgeo Milky White UBR Liquid 263 Padding & Exhaust at medium temperature HEXASULPHO GROUP Bridgeo Milky White AS Liquid -- Padding and exhaust at low temperature. Bridgeo Milky White HF Liquid (UF AS LIQ) -- Padding and exhaust at low temperature.
