Sintered Filter Feature 1. Sintered filter is surface filtration 2. Sintered filter is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Sintered filter has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Sintered Filter Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Introduction: The main filter material of the stainless steel sintered filter element uses 304, 304L, 316, 316L stainless steel fiber sintered felt and stainless steel woven mesh as the main filter medium. The stainless steel fiber sintered felt is a porous deep-shaped filter material made of stainless steel fibers through high temperature sintering; stainless steel; Woven mesh is woven from stainless steel wire. characteristic: 1. The stainless steel precision filter element has high porosity, good air permeability, low resistance and low pressure difference; 2. After the stainless steel precision filter element is folded, the filter area is large and the dirt holding capacity is large; 3. The stainless steel precision filter element is resistant to high temperature and corrosion, and is suitable for filtering high viscous liquids; 4. Good regeneration performance, can be used repeatedly after chemical cleaning, high temperature and ultrasonic cleaning; , All stainless steel structure, wide chemical compatibility; The main technical parameters: 1. Working temperature of stainless steel precision filter element: 500 2. Filtration accuracy: 1-200um 3. Working temperature: 0.1-30MPa 4. Filter element specifications: 5-40 inches (can be made according to user requirements) 5. Interface form: threaded interface, 222, 226, 220, etc.
Customized connector pleated sintered filter cartridges are filter elements that are made of stainless steel wire mesh or sintered metal fiber felt. The filter cartridges are formed by sintering at the contact points of the wire mesh, creating a porous filter cylinder with high surface filtration performance. The cartridges feature a pleated design, providing a larger filtration area and strong dirt-holding capacity. They can be provided with double-open ends or single-open ends, often accompanied by threaded end gaskets (such as O-rings) to reduce friction. Specifications Material: Stainless steel 304/316L or other special alloys Filtration precision: 1-300 microns Porosity: Up to 90% Length: 99-1490 mm Diameter: 35-80 mm Operating temperature: -200�°C to 600�°C Cleaning methods: Backwashing, ultrasonic cleaning Connector: As per drawing requirements Features High dirt-holding capacity: The pleated design provides a larger filtration area, allowing the filter cartridge to efficiently capture and retain dirt, extending its service life. Corrosion resistance: The filter cartridge is made of stainless steel throughout, exhibiting excellent corrosion resistance and suitable for filtering various corrosive media. High strength and stability: The filter cartridge possesses high strength and stability, capable of withstanding high pressure and harsh operating conditions, ensuring reliable operation of the filter. Multiple filtration grades: Different filtration grades of filter cartridges can be provided to meet various particle size filtration requirements. Easy to clean: Pleated sintered filter cartridges can be cleaned through various methods, including backwashing, reverse flow, and ultrasonic cleaning, while still maintaining high filtration efficiency after cleaning. Applications Chemical industry Oil and gas industry Food and beverage industry Pharmaceutical industry Electronics industry Automotive industry Other industrial applications
Sintered Filter Element Feature 1. Sintered filter element is surface filtration 2. Sintered filter element is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Sintered filter element has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Sintered Filter Element Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
SS Sintered Filter Cartridge Feature 1. SS sintered filter cartridge is surface filtration 2. SS sintered filter cartridge is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. SS sintered filter cartridge has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life SS Sintered Filter Cartridge Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
SS Sintered Filter Element Feature 1. SS sintered filter element is surface filtration 2. SS sintered filter element is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. SS sintered filter element has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life SS Sintered Filter Element Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Multilayer Sintered Filter Cartridge Feature 1. Multilayer sintered filter cartridge is surface filtration 2. Multilayer sintered filter cartridge is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Multilayer sintered filter cartridge has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Multilayer Sintered Filter Cartridge Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Multilayer Sintered Filter Element Feature 1. Multilayer sintered filter element is surface filtration 2. Multilayer sintered filter element is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Multilayer sintered filter element has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Multilayer Sintered Filter Element Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Multilayer Sintered Filter Feature 1. Multilayer sintered filter is surface filtration 2. Multilayer sintered filter is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Multilayer sintered filter has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Multilayer Sintered Filter Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Multi-layered Sintered Filter Disc Sintered Mesh Laminates Filters & Baskets Stainless Steel Sintered Filter Disc FEATURES · High rigidity and stability for long service life. · Excellent resistance to corrosion, acid, alkali and abrasion. · High heat resistance, it can be used under the temperature ranging from -200 °C to 600 °C. · Various filter ratings to choose and great filter precision for different uses. · Good dirt holding capacity. · Easy to clean and reusable, therefore reduce downtime. Grommet type seal sintered cartridge PARAMETER Sintered metal filter discs are ideal filter elements for accurate filtration. It is made from sintered wire mesh through laser-cutting. Sintering is a process which produces fusion bonds at all contact points of the woven wire mesh in the vacuum environment with high temperature. Sintering maintains the uniformity of the original weave and fixes the hole size, shape and micron rating of the mesh. The sintered wire mesh can be single layered or multi-layered, whichever is full of high strength and rigidity. For various purposes, sintered metal filter discs can be processed into different shapes, like round, toroidal, square, oval or fan-shaped. According to customers' demand, sintered metal filter discs can also be added outer rings. Sintered mesh filter disc is widely used in filtration process in many industries, it works as gas-liquid separation, oil and fuel filtration. YMX FILTER MANUFACTURING CO., LTD is a custom fabricator of series of wire screen, cone strainers and woven wire cloth products. For more than 20 years' experience, we are serving customers from a wide range of industries from all over the world. If you are interested in custom wire screen, you can click here to browse our website.
Customized connector pleated sintered filter cartridges are filter elements that are made of stainless steel wire mesh or sintered metal fiber felt. The filter cartridges are formed by sintering at the contact points of the wire mesh, creating a porous filter cylinder with high surface filtration performance. The cartridges feature a pleated design, providing a larger filtration area and strong dirt-holding capacity. They can be provided with double-open ends or single-open end, often accompanied by threaded end gaskets (such as O-rings) to reduce friction. Compared to cylindrical filters of the same size, the folded design of pleated sintered filter cartridges can offer up to 3 times more dirt-holding capacity while occupying less installation space. Pleated sintered filter cartridges can be easily cleaned through backwashing, reverse flow, ultrasonic cleaning, or other methods. Even after 3 to 5 cleaning cycles, they can still maintain over 90% of their original filtration efficiency. Specifications Material: Stainless steel 304/316L or other special alloys Filtration precision: 1-300 microns Porosity: Up to 90% Length: 99-1490 mm Diameter: 35-80 mm Operating temperature: -200�°C to 600�°C Cleaning methods: Backwashing, ultrasonic cleaning Connector: As per drawing requirements Features High dirt-holding capacity: The pleated design provides a larger filtration area, allowing the filter cartridge to efficiently capture and retain dirt, extending its service life. Corrosion resistance: The filter cartridge is made of stainless steel throughout, exhibiting excellent corrosion resistance and suitable for filtering various corrosive media. High strength and stability: The filter cartridge possesses high strength and stability, capable of withstanding high pressure and harsh operating conditions, ensuring reliable operation of the filter. Multiple filtration grades: Different filtration grades of filter cartridges can be provided to meet various particle size filtration requirements. Easy to clean: Pleated sintered filter cartridges can be cleaned through various methods, including backwashing, reverse flow, and ultrasonic cleaning, while still maintaining high filtration efficiency after cleaning.
The SUS316L powder sintered filter cartridge is a type of filter cartridge used for filtration in various industries such as pharmaceuticals, food and beverage, electronics, and water treatment. The L stands for low carbon content, which further enhances its resistance to corrosion and makes it suitable for use in environments that are prone to corrosion. The SUS316L powder sintered filter cartridge is made by compressing and sintering stainless steel powder to form a porous structure with uniform pore size and distribution. This structure allows for high flow rates and efficient filtration of particles and contaminants from fluids. Parameters Material: SUS316 Craft molding and sintering Size: customized Usage: filtration Features 1.High filtration efficiency: The multiple layers of stainless steel mesh provide a high filtration surface area, which results in a high filtration efficiency. 2.High temperature resistance: SUS316L stainless steel can withstand high temperatures, which makes it ideal for applications where high-temperature resistance is required. 3.Long service life: The sintered metal powder structure of the filter cartridge results in a high-strength, durable filter that has a long service life. 4.Wide range of applications: SUS316L powder sintered filter cartridges are suitable for a wide range of applications, including in the chemical, pharmaceutical, food and beverage, and water treatment industries. Applications SUS316L powder sintered filter cartridges are commonly used in applications where high-performance filtration is required, and where the filter cartridge needs to withstand high temperatures, pressures, and corrosive environments. Pharmaceuticals: SUS316L powder sintered filter cartridges are commonly used in pharmaceutical manufacturing processes to filter out contaminants and impurities from liquids, including water, solvents, and drug formulations. Food and beverage: In the food and beverage industry, SUS316L powder sintered filter cartridges are used to filter out impurities from liquids such as juices, beer, and wine, and to remove particulate matter from cooking oils. Electronics: SUS316L powder sintered filter cartridges are used in the electronics industry to filter out particulate matter from chemicals and solvents used in the manufacturing of electronic components. Water treatment: In water treatment plants, SUS316L powder sintered filter cartridges are used to filter out impurities and particles from water, including sediment, bacteria, and other microorganisms. Chemical processing: SUS316L powder sintered filter cartridges are used in chemical processing applications to filter out contaminants and impurities from liquids used in various chemical reactions.
Powder sintered filter elements for filtration are a type of porous filter made by sintering metal powders into a solid structure with interconnected pores. Powder sintered filter elements for filtration have a high surface area and are capable of filtering particles from liquids and gases. They are commonly used in applications where high temperatures and corrosive environments are present, such as in chemical processing, oil and gas refining, and power generation. Parameters Material: titanium powder Craft: sintering Size: customized Features 1.Precise Filtration: Powder sintered filter elements can be designed with a specific pore size to provide precise filtration of particles and contaminants, down to the submicron level. 2.High Dirt Holding Capacity: Powder sintered filter elements have a high dirt holding capacity, meaning they can retain a large amount of particulate matter before requiring replacement or cleaning. 3.Reusability: Powder sintered filter elements can be easily cleaned and reused, making them a cost-effective solution in applications where frequent filter replacement is required. 4.Customizable Shapes and Sizes: Powder sintered filter elements can be manufactured in a range of shapes and sizes, including cylinders, discs, cones, and tubes, to fit specific applications and equipment. Applications Powder sintered filter elements are a versatile and effective solution for a wide range of filtration applications, particularly where high temperatures, corrosive environments, and precise filtration is required. Chemical Processing: Powder sintered filter elements are used for the filtration of corrosive chemicals and solvents, such as acids, alkalis, and organic compounds. They are also used for the separation of catalysts and the purification of process streams. Oil and Gas: Powder sintered filter elements are used in oil and gas processing for the removal of contaminants, such as sand, scale, and other solid particles. They are also used for the filtration of natural gas, as well as in fuel and hydraulic systems. Food and Beverage: Powder sintered filter elements are used in the food and beverage industry for the filtration of liquids, such as juices, beer, and wine. They are also used for the removal of impurities and contaminants, such as bacteria and particles. Pharmaceuticals: Powder sintered filter elements are used in the pharmaceutical industry for the filtration of liquids and gases in the manufacturing process of drugs and vaccines. They are also used for the removal of contaminants, such as bacteria, viruses, and particles. Water Treatment: Powder sintered filter elements are used for the removal of impurities and contaminants in water treatment applications. They are used for the filtration of drinking water, wastewater, and industrial process water.
Stainless Steel Sintered Filter Cartridge Feature 1. Stainless steel sintered filter cartridge is surface filtration 2. Stainless steel sintered filter cartridge is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Stainless steel sintered filter cartridge has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Stainless Steel Sintered Filter Cartridge Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Stainless Steel Sintered Filter Element Feature 1. Stainless steel sintered filter element is surface filtration 2. Stainless steel sintered filter element is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth 3. Stainless steel sintered filter element has uniform pore size distribution 4. Wire mesh will not shed in filtration process 5. High compression strength 6. High mechanical strength 7. High rigidity 8. High abrasion resistance 9. Good durability against most liquids, gases and aggressive steam 10. High temperature resistance 11. High filter rating accuracy 12. High filter efficiency 13. Good corrosion resistance 14. Washable and Cleanable 15. Reusable 16. Long service life Stainless Steel Sintered Filter Element Technical Parameter Raw Material: SS 316L, SS 304 Filter Media: ZWEN Sintered Wire Mesh Filter Rating: 0.5-300 Microns Filter Efficiency: > 99.99 % Operation Temperature: â?¤ 816 Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others Gasket: PTFE, Viton, Silicone, Buna-n, EPDM Connector: 1. DOE 2. 220 3. 222 4. 226 5. Thread (NPT,BSP,G,M,R) 6. Flange 7. Special customization Application Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Product Introduction Stainless steel powder sinter filter element is a kind of filter material, which is made of stainless steel powder sintered at high temperature. The filter element has high permeability, can effectively filter tiny particles and impurities, has high corrosion resistance and durability, and is suitable for liquid and gas filtration in various chemical, food, pharmaceutical, electronic and other industries. Product parameters Diameter: 50mm-1200mm Length: 100mm-2000mm Filtration accuracy: 1m-100m Filtration area: 0.1-1000 Maximum working temperature: 600 C Resistance coefficient:
Stainless steel powder sintered filter element is a kind of filter material, which is made of stainless steel powder sintered at high temperature. The filter element has high permeability, can effectively filter tiny particles and impurities, has high corrosion resistance and durability, and is suitable for liquid and gas filtration in various chemical, food, pharmaceutical, electronic and other industries. Product parameters Diameter: 50mm-1200mm Length: 100mm-2000mm Filtration accuracy: 1 m-100 m Filtration area: 0.1-1000 Maximum working temperature: 600 C Resistance coefficient:
Product Introduction The SUS316L powder sintered filter cartridge is a type of filter cartridge used for filtration in various industries such as pharmaceuticals, food and beverage, electronics, and water treatment. The L stands for low carbon content, which further enhances its resistance to corrosion and makes it suitable for use in environments that are prone to corrosion. The SUS316L powder sintered filter cartridge is made by compressing and sintering stainless steel powder to form a porous structure with uniform pore size and distribution. This structure allows forhigh flow ratesand efficient filtration of particles and contaminants from fluids. Features 1. High filtration efficiency: The multiple layers of stainless steel mesh provide a high filtration surface area, which results in a high filtration efficiency. 2. High-temperature resistance: SUS316L stainless steel can withstand high temperatures, which makes it ideal for applications where high-temperature resistance is required. 3. Long service life: The sintered metal powder structure of thefilter cartridgeresults in a high-strength, durable filter that has along service life. 4. Wide range of applications: SUS316Lpowder sintered filter cartridgesare suitable for a wide range of applications, including in the chemical, pharmaceutical, food, beverage, and water treatment industries. Applications SUS316L powder-sintered filter cartridges are commonly used in applications where high-performance filtration is required, and where the filter cartridge needs to withstand high temperatures, pressures, and corrosive environments. Pharmaceuticals: SUS316L powder sintered filter cartridges are commonly used in pharmaceutical manufacturing processes to filter out contaminants and impurities from liquids, including water, solvents, and drug formulations. Food and beverage: In the food and beverage industry, SUS316L powder sintered filter cartridges are used to filter out impurities from liquids such as juices, beer, and wine, and to remove particulate matter from cooking oils. Electronics: SUS316L powder sintered filter cartridges are used in the electronics industry to filter out particulate matter from chemicals and solvents used in the manufacturing of electronic components. Water treatment: In water treatment plants, SUS316L powder sintered filter cartridges are used to filter out impurities and particles from water, including sediment, bacteria, and other microorganisms.
sintered glass filter mediasintered glass filter media sintered glass filter media Factory Supply sintered glass filter media Our main product is sintered glass filter media, filter tube, filter cylinder, filter disc etc., the main part of our product is made of stainless steel wire mesh, the mesh detailed specifications is as follow: Material: AISI304, AISI 304L, AISI 316, AISI 316L etc. Normal mesh size: Plain weave: 0.5X0.5mesh to 635X635 mesh; Twill weave:20x20mesh to 400x400mesh; Plain dutch weave:10X64mesh to 80X700mesh; Twill dutch weave:20x250mesh to 400X2800mesh; Reversed dutch weave: 48x10mesh to 720x150mesh. Wire diameter:0.025mm-1.8mm. Features: High tension: Much higher tension than common polyester mesh and smooth tension; Super precision: Uniform wire diameter and aperture with extremely low difference; Low elongation: Very small elongation of wire mesh at high tension; High flexibility: The wire mesh will not lose elasticity at extreme tension; High corrosion resistance: The excellent corrosion resistance of stainless steel wire exceeds polyester fiber. Usage for the micron stainless steel mesh filter: Micron Mesh Mainly used for Separation and Filtration, extensively used in petroleum, chemical industry, environment protection, mine, airspace, paper-making, electronic, metallurgy etc. Widely used for water, air,liquid filter. sintered glass filter media sintered glass filter mediasintered glass filter media [ Packing ] sintered glass filter mediasintered glass filter media [ Payment term ] 1)100%T/T in advance if order amount less than USD10000.00 2) 30% paid in advance and 70% balance paid before shipment if order amount more than USD10000.00. 3) Irrevocable L/C at sight. Any other payment term can be negotiatory. sintered glass filter media
Sintered industrial filter elements 1.Material:316l, 304 2.Filtering micron:1um-200um 3.Filter media:sintered mesh plate & sintered metal fiber felt 4.Size:on customers' drawing. 5.Shape:filter cartridges, filter disc, filter panel, pleated filter elements, perforated filter cartridges and etc. 6.Connect adaptor: flange, thread inserts, and etc. 7.Sintered filter elements high heat resistant, large filter area, less lost of pressure, easy to wash and assembly. 8.Working temperature:-200-600c. Wooden case, plastic film.
