Dewormer Safe Guard.
Dega gas detector -stationary, compact - dega 04 Compact detector from new series, which substitute type DEGA 03,.Serves to one- or two- Level signalization of detected gas concentration in guarded area. Its construction, kind of installation and service is designed for use in smaller business, boiler rooms, garages etc.. Detector used semiconductance sensor, which transforms change of concentration of detected gas at change of electrical resistance.Exceed of pre-set limits is signalized optical, acoustic or with internal siren and switch of potential-free relays contacts. It ś possible to energize device with system voltage 230 V AC, 12 or 24 V DC.
I m2 ex d i, ii 2gd ex d td a iib t3-t4t tmax. Surf. Ip 65 ex. Technical description: luminaire consists from body, basic plate and Flange with protective glass. Body and flange are castings from grey cast Iron treated with polyester powder paint. Luminaire can be suspended By the steel pendant with 2 eyes o 18 mm on the upper part of the Body. Connecting area (increased safety „d“), with connecting clamps and 2 cable glands, is placed on the side of luminaire. Flange cable glands No. 3-99.5747/1 from grey cast iron are designed for cable o 10 - 16 Mm (no. 3-99.6170/1 for o 16 – 20 mm optionally). Area is enclosed With cover from grey cast iron. Steel basic plate with electric parts And reflector is fixed in the body. Flange with glass cover is screwed In the body and secured with locking screw and silicon sealing Against unlocking, thread shapes a rift of flameproof enclosure „d“. Protective hardened glass resistant against mech. Shock min. 7 j is Fixed to the flange, the connection is filled with polyurethane putty. A steel hinge is fixed to the flange as the mobile one and enables to Hang the flange during mounting or dismounting. Steel parts are Galvanized and chromated. Luminaire is equipped with protective guard from steel wire. Max. Section of connecting conductors 4 mm2. Three-pole connecting terminal block enables interchanging 2 phases. Luminaire is equipped with 2 inner and 1 outer earthing clamps for conducting connection. Luminaire is designed as the through-way one for 4-core cable; when used as the end piece, there is necessary to use blinding plug (optionally on order). Packing carton is filled with polyurethane foam instapak. Luminous sources: Spc 300 and 500w, with ballast box hql 250w, 400w, nav-e 210, 350w Carton (mm/pcs) 560x300x30mm, weight 24 kg/pc
Technical description: luminaire consists from body, basic plate and flange With protective glass. Body and flange are castings from grey cast iron treated With polyester powder paint. Steel pendant with eye o 18 mm is fixed to the Upper part. Connecting area (increased safety „d“), with connecting clamps And 2 cable glands, is placed on the side of luminaire. Flange cable glands No. 3-99.5747/1 from grey cast iron are designed for cable o 10 - 16 mm (gland No. 3-99.6170/1 for cable o 16 - 20 mm). Area is enclosed with cover from Grey cast iron. Steel basic plate with electric parts and reflector is fixed in the Body. Flange with glass cover is screwed in the body and secured with locking Screw and silicon sealing against unlocking; thread shapes a rift of flameproof Enclosure „d“. Protective hardened glass is resistant against mech. Shock min. 7 j and is fixed in the flange, the connection is filled with a polyurethan putty. A steel hinge is fixed to the flange as the mobile one and enables to hang Up the flange during mounting or dismounting. Steel parts are galvanized And chromated. Luminaire is equipped with protective guard from galvanized Steel wire. Max. Section of connecting conductors 4 mm2. Three-pole connecting Terminal block enables interchanging 2 phases (4-core cable). Luminaire Is equipped with 2 inner and 1 outer earthing clamps for conductive connection. Luminaire is designed as the through-way one, when used as end piece, there is Necessary to use blinding plug (optionally on order). Packing carton is filled with Polyurethane foam instapak. Luminous sources: Hwl160 w e27, dulux d26 w g24d-3, bulb100w/220 e27, nav-e 110 w e27, hql125 w e27, nav-e 50/l 50 w e27, hql 80 w e27, clas 200 w e27, master pl e 23 w e27 and next Carton (mm/pcs) 430x240x240, weight 18 kg/pcs
2G Ex de IIC T4-T6 Gb II 2G Ex de IIC T4-T6 Gb II 2D Ex t IIIC T max.surf Db Luminaire consists of body, basic plate and flange with protective glass. Body and flange are made of AlSi alloy treated with polyester powder paint. Luminaire can be suspended by the help of steel pendant with eye o 18 mm. The connecting area (increased safety „e“) is placed on the side of the body and equipped with connecting clamps and 2 cable glands HSK-K-Ex M25x1.5 for cables o 9-16 mm. Area is enclosed with cover and sealed with silicon. There is aluminium basic plate with electro-module mounted inside the luminaire. Electro-module consists of 20 x LED CREE XP-G (luminous flux 4000 lm, lumen per watt 88 lm/W, colour temperature 3700-5000, Colour Rendering Index ~80, guaranteed life-time min. 50.000 hrs.) and cooling unit. Input of the luminaire is adjustable (45W/22,5W) by changing output current of the LED driver 700mA/350mA. Flange with protective glass is screwed in the body and locked with securing screw; thread shapes a rift of flameproof enclosure „d“. Protective hardened glass is resistant against mech. shock min. 7 J and is fixed in the flange; the connection is filled with polyurethane putty. The mobile steel hinge is fixed to the flange and enables to hang up the flange during mounting and dismounting. Steel parts are galva-nized and chromated. Max. section of connecting conductors 4 mm2. Three-pole connecting terminal block enables interchanging 2 phases (4-core cable). Luminaire is equipped with 2 inner and 1 outer earthing clamp for conductive connection. Luminaire is designed as through-way one, when used as the end piece there is necessary to substitute one cable gland with blinding screw V-Ex or to blind one unused cable gland with blinding plug HSK-V-Ex. The blinding parts can be delivered on order optionally. Versions K are equipped with protective guard from steel wire. Packing carton is filled with sealing polyurethane foam Instapak. luminous sources: EcoClasik 140W E27, CLAS 200W E27, DULUX D26 W G24d-3, Bulb100W/220 E27, NAV-E 110 W E27, HQL125 W E27, NAV-E 50/l 50 W E27, HQL 80 W E27, Master PL E 23 W E27 and next. Carton 410 cm x 240 cm x 240cm , Weight 10 kg/pc
Ii 2g ex de iic t6 gb Ii 2d ex t iiic t 60 °c db Luminaire consists of body, basic plate and Flange with protective glass. Body and flange are made of alsi alloy Treated with polyester powder paint. Luminaire can be suspended By the help of steel pendant with eye o 18 mm. The connecting area (increased safety „e“) is placed on the side of the body and equipped With connecting clamps and 2 cable glands hsk-k-ex m25x1.5 for cables O 9-16 mm. Area is enclosed with cover and sealed with silicon. There is Aluminium basic plate with electro-module mounted inside the Luminaire. Electro-module consists of 20 x led cree xp-g (luminous Flux 4000 lm, lumen per watt 88 lm/w, colour temperature 3700-5000, Colour rendering index ~80, guaranteed life-time min. 50.000 hrs.) and Cooling unit. Input of the luminaire is adjustable (45w/22, 5w) by changing Output current of the led driver 700ma/350ma. Flange with protective Glass is screwed in the body and locked with securing screw; thread Shapes a rift of flameproof enclosure „d“. Protective hardened glass is Resistant against mech. Shock min. 7 j and is fixed in the flange; the connection Is filled with polyurethane putty. The mobile steel hinge is fixed to The flange and enables to hang up the flange during mounting and dismounting. Steel parts are galva-nized and chromated. Max. Section of connecting conductors 4 mm2. Three-pole connecting terminal block enables interchanging 2 phases (4-core cable). Luminaire is equipped with 2 inner and 1 outer earthing clamp for conductive connection. Luminaire is designed as through-way one, when used as the end piece there is necessary to substitute one cable gland with blinding screw v-ex or to blind one unused cable gland with blinding plug hsk-v-ex. The blinding parts can be delivered on order optionally. Versions k are equipped with protective guard from steel wire. Packing carton is filled with sealing polyurethane foam instapak. Carton 410 cm x 240 cm x 240cm , Weight 10 kg/pc
1.. Uveïte podrobnosti a technické specifikace 2G Ex de IIC T3-T6 Gb II 2G Ex t IIIC Tmaxsurf.-table Db Technical description: Luminaire consists of body, basic plate and flange with protective glass. Body and flange are castings from AlSi alloy. Steel hinge with eyes o 18 mm is fixed on the upper part of the body. Connecting area (increased safety „e“), with connecting clamps and 2 cable glands HSK-K-Ex M25x1.5 for cables o 9 – 16 mm (HSK-M-Ex for cables 10 – 16 mm for versions F), is placed on the side of the body. This area is covered with cover and sealed with silicon. Steel basic plate with electric parts and reflector is fixed in the body. Flange with protective glass is screwed into the body and secured with securing screw against unlocking; the thread creates a rift of flameproof enclosure „d“. Protective cover from hardened glass is resistant against mechanical shock min. 7 J and is fi xed in fl ange; the connection is filled with a putty (polyurethane glue). Steel mobile hinge is fixed on the flange and enables to hang up the flange under body during mounting or exchanging light source. AlSi parts of luminaire are treated with polyester powder paint; steel parts are galvanized and chromated. Max. section of connecting conductors 4 mm2. Three-pole connecting terminal block enables interchanging 2 phases (4-core cable). Luminaire is equipped with 2 inner and 1 outer earthing clamps. Luminaire is designed as through-way one. When it is used as the end piece, there is necessary to replace one cable gland with blind screw V-Ex or to blind one unused gland with blind plug HSK-V-Ex (versions F: one cable gland must be replaced with blinding screw V-Ms-VMQ-Ex). Blinding parts are not attached - delivered optionally on order only. Versions K are equipped with protective guard from steel wire. All types can be equipped with lampshade (optionally on order only). Packing carton is filled with polyurethane foam Instapak luminous sources: HWL 500W E40, SPC A T CL 250W E40, HQL 250W E40, NAV-E350 350W E40 and other. NOTE ! Ballast box 205.1 can be used for HP Mercury and sodium lamps.. Carton 560 cm x 350 cm x 300cm , Weight 12 kg/pc
