Find Verified Pyrolysis Machine Suppliers, Manufacturers and Wholesalers

Beston pyrolysis machine turns waste tire, waste rubber, oil sludge into pyrolysis oil. You can also get carbon black and steel wire. The whole process is environmentally friendly.

Number Items Introduction 1 Model JZB-5 JZB-8 JZB-10 2 Raw material Waste plastic and rubber Waste plastic and rubber Waste plastic and rubber 3 Structural form Horizontal Horizontal Horizontal 4 Capacity/day About 5 tons About 8 tons About 10 tons 5 Pressure Atmospheric Atmospheric Atmospheric 6 Rotate speed of the reactor 0.4R/min 0.4R/min 0.4R/min 7 Cooling form Water Water Water 8 Heating form Direct Direct Direct 9 Installation mode Base Base Base 10 Noise db(A) 85 85 85 11 Working mode Intermittent Intermittent Intermittent 12 Size of reactor 2200¡Á6000 2200¡Á6600 2600¡Á6600 13 Volumeof reactor 16 m3 19 m3 23m3 14 Weight of reator About 5 tons About 5.5 tons About 6 tons 15 Production cycle 12 days 12 days 12 days 16 Installation cycle 12 days 12 days 12 days.

Waste tire continuous pyrolysis machine Process The waste tire is shredded into tire chips and continuously to be fed into the drum reactor for the normal pressure low temperature pyrolysis; â?? The pyrolyst oil gas is turned into fuel oil and little combustible gas after fractionation and cooling through oil separator. The raw carbon black will be automatically transferred to the carbon black production system. The combustible gas will be totally used as fuel to the system after scrubbing process. The heating system adopts residual heat recycling technology, which far saving energy consumption and low down the running cost. The gas produced by the production line will be purified to meet the environmental standard then discharged.

ã??Daily Capacityã?? 6 - 30 T ã??Working Methodã?? Batch, Semi-Continuous, Fully Continuous ã??Raw Materialã??Waste Tyre, Waste Plastic, Rubber, Oil Sludge

Established in 2004, MC Pyrolysis is a professional manufacturer of advanced continuous model Pyrolysis Plant and Recovered Carbon Black Refining Plant. After many years of research and development, we developed continuous model pyrolysis plant and RCB Refining Plant. The product is practical, reliable and cost-effective. We can provide customers with a complete set of recycling solutions: Shredder Crusher Pyrolysis Distillation Plant RCB refining Plant. The End-of-life tires and Waste plastics can be reduced without pollution. The refined carbon black can used in new tires and other rubber products. It helps to reduce carbon black dioxide emissions. The solution has been used in Europe, the United States, China and other countries. The plants are running well. Welcome to contact us.

Old tire pyrolysis technology is a green technology that solves waste tire pollution to the environment. And can ease the energy crisis, in today's society, this is a very meaningful environmental protection industry. Tire pyrolysis oil is an end product extracted from the pyrolysis process and is often used to heat raw materials and generate electricity with heavy machinery. If the pyrolysis oil is subjected to a specialized pyrolysis oil distillation plant distillation, the extracted diesel oil can be used for diesel generators and light fuel oils. The main part of the entire pyrolysis system includes reactors, transmissions, catalysis rooms, cooling pipes, manifolds, heavy oil tanks, light oil tanks, condensers, oil-water separators, safety devices, vacuum systems, dust collection systems, etc. The main working principle of old tire refining equipment: By pyrolysis of the oil using a high-temperature distillation tire, the impurities in the oil are distilled off, and the filtered light oil vapor increases in heat, and impurities in the pyrolysis oil fall into the furnace. Light oil and gas passes through a multi-stage heating system, is filtered, enters a cooling system, is then liquefied, passes through a water separator, and flows into a light oil tank. After degreasing and desulfurization, clean and transparent diesel oil can be obtained. The average diesel yield is 80%-85%. Finally, the residue in the furnace is discharged from the furnace. It is a substance that functions like asphalt. The approximate yield of bitumen is: 15%-20%. The end product of the Dongying Group's used tire refining equipment was diesel oil and asphalt. What are their main uses? 1. Diesel: Mainly used for heavy machinery, generator power oil, and boiler heating combustion oil. 2. Asphalt: Mainly used for direct paving, or sent to asphalt refineries.

1.Application area: Widely used in light weight, fine powder materials granulating.The more fine powder is, The higher the spherical degree is, the better the granule quality is.Generally, granule Particle size should be bigger than 300 mesh. 2.Standard type material: Tyre pyrolysis carbon black powder 3.Technical advantage: Do not need any adhesives in the process of granulating The equipment belongs to continuous granulating.After powder granulating, it is Easier to control the dust float in the air problem in the subsequent section . This equipment is via highspeed rotating member with stirring tooth producing Huge mechanical force and aerodynamic force, then become spherical particle, Compared with natural reunion granulation equipment line rotary disk granulator, Rotor drum granulator the ending granule intensityis higher, and the granule size Distribution is more concentrated. Product appearance is beautiful:granule shape is spherical, degree of Sphericity¡ý0.8, granule size is between 0.7-2mm, granulation rate¡ý98%. Easy to control:the size of the granule diameter could be adjusted via material Moisture content and spindle speed.Generally the lower the moisture content is And the higher speed is , the smaller the particle is , and vice versa. Adaptability high.Could be used in a variety of viscous or non viscous powder Granulation and forming The whole equipment structure is compact , operation is stable and reliable, large Production capacity(1-1.5t/h) Delivery time:within 15 days after receipt the payment.

1.Application area: Widely used in light weight, fine powder materials granulating.The more fine powder is, The higher the spherical degree is, the better the granule quality is.Generally, granule Particle size should be bigger than 300 mesh. 2.Standard type material: Tyre pyrolysis carbon black powder 3.Technical advantage: Do not need any adhesives in the process of granulating The equipment belongs to continuous granulating.After powder granulating, it is Easier to control the dust float in the air problem in the subsequent section . This equipment is via highspeed rotating member with stirring tooth producing Huge mechanical force and aerodynamic force, then become spherical particle, Compared with natural reunion granulation equipment line rotary disk granulator, Rotor drum granulator the ending granule intensityis higher, and the granule size Distribution is more concentrated. Product appearance is beautiful:granule shape is spherical, degree of Sphericity¡ý0.8, granule size is between 0.7-2mm, granulation rate¡ý98%. Easy to control:the size of the granule diameter could be adjusted via material Moisture content and spindle speed.Generally the lower the moisture content is And the higher speed is , the smaller the particle is , and vice versa. Adaptability high.Could be used in a variety of viscous or non viscous powder Granulation and forming The whole equipment structure is compact , operation is stable and reliable, large Production capacity(1-1.5t/h) 4.The specification of the our line

Waste tyre recycling line refine tyre to waste rubber oil.Waste tyre recycling to fuel oil plant take high temperature pyrolysis technology to get waste rubber oil refined.After waste rubber oil refining, waste rubber oil production can be used as good fuel material. (d*l)2200*6000mm, 25t; 2200*6600mm, 28t; 2600*6600mm, 30t

(1)safety A. The waste gas produced during the process is alkyl from c1 to c4, which is dangerous when burning directly. In our process, it is firstly transferred through waste Gas recycle system and a safe device spray gun. Before burning, we should ensure the safety of production. B. Pressure gauge, alarming device and safety valve. (2)environmental protective A. Effective water dedusting system can avoid black smoke. B. The exhaust gas will be recycled for heating reactor to save energy and no pollution C. Every junction of the reactor is in good sealing situation with professional sealing material. D. Waste solid. The solid residua will be left in the reactor. Its main component is black carbon.It can be the raw material industrial black carbon. Also could be mixed with the pulverized coal ash as raw material in thermal power plant, also could be the raw material of pulverized coal ash brick (one kind of environmental protective building material). Container