Two roll plate bending roller machine Brief introduction sheet roller machine 2 roll rolling machine is often said that the two-roll roller machine, BSR automatic hydraulic two-roll bending roller machine is mainly used for rolling a variety of sheet metal into a cylindrical workpiece, it is learned at home and abroad Blower robot Advanced technology, based on its own research and development of products, the use of hydraulic drive, CVT, easy operation, high precision control, energy significantly, greatly improving production efficiency and reduce labor intensity. This product mechanical efficiency of similar products 4-6 times the energy consumption for similar products 1 / 10-1 / 8. It is widely used in the industries of solar water heater, pressure vessel, silencer, automobile fuel tank, hardware appliance and so on. It is widely used in stainless steel, carbon steel, aluminum and other metal materials. Advantages of sheet metal rolling machine BSR automatic hydraulic two-roll metal rolling machine round volume accuracy, eliminating the three-roll bending machine straight edge, pre-bending problem; The rolling precision of the parts is round, the operation is convenient, the precision is reliable, the efficiency is high, the output is high, is used for rolling the various metal sheet into the tube shape, the thickness of the coil plate is adjustable, the rolling time of the single work piece is about 10-15 seconds; Control system uses imported programmable controller, other major components are imported or domestic famous brands, low failure rate, stable and reliable performance, hydraulic system pressure regulator convenient. Technical parameter of roller rolling machine for metal
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
Cast iron skulls, cast iron borings and turnings, steels skulls, eaf skulls, plate iron, mill scale, metal scrap, incinerated scrap (e46).
Scope of application :clean vegetable processing ,central kitchen ,large dining canteen,catering chain ,food factory ,etc . Vegetable Roller spray cleaning machine
Thickness 2-100mm Width plate:600-2250mm,strip:24-600mm Length 1m-12m Material Q235,Q345,ST37,A36,16Mn,45# Standard GB/T709-1988 Edge Type Scrap edge(Q); No trimming(BQ) Place of origin Taian, China(mainland)
1.The Mild steel grade are:DCO01,SPCC,Q235C,Q235D,Q235E;Q345B,Q345C,Q345E,Q345E. 2.Shipbuilding steel plate.Mainly used in ship build. The grades are:A32,AH32,A36,AH36,DH36,AH36,D32,DH32 ETC. 3.Carbon structural and high strength steel plate.Mainly used in bridges,power station equipment,lifting machinery,mining macinery and other large welding structural parts.Q460C/D/E,Q235B/C/D/E,Q609C/D/E 4.Alloy Steel Plat.Mainly used in Machinery,structure,tool,etc. 40Cr,50Mn,65Mn,15CrMo,35CrMo,42CrMo etc.
1> Back To Back Towel Bars(with and without metal washers) 2> Pull handled available in various sizes with back to back Towel bars 3> Glass thickness : 6 mm~12 mm 4> Size: 19 x 6"/8"/10/12"/18"/24" C/C 5> Material :304 Stainless Steel / #62 Brass Tubular 6> Chrome plated, Brushed Nickel, Brass Polished, Polished Chrome, Gold Plated, Oil Rubbed Bronze.
1. Available in different models 2. CNC machined precision pivot pins 3. Glass to Glass, wall to Glass shower door bi-fold hinges. 4. Glass thickness: 6 mm~10 mm 5. Max door weight: 23 kg (with 2 hinges) 6. Feature: 14mm Diameter hole required (non cutout),free swinging 7. Material: SS304 8. Closing angles 180°degree. 9. Straight edges, beveled edges, round edges. 10. Glass preparation- 14mm Diameter hole required. 11. Chrome plated, Brushed Nickel, Gold Plated, Oil Rubbed Bronze.
We supply attractive variety qualitative range of Toilet and Bathroom accessories. Features of our Shower door hinges · CNC machined precision pivot pins · Dimension 90mmx 55mm (varies from hinge to hinge) · Chrome plated, Brushed Nickel, Brass Polished, Polished Chrome, Gold Plated, Oil Rubbed Bronze. · Solid brass, Zinc as per customer choice. · Glass to Glass, wall to Glass shower door hinges. · Closing angles 90°, 135°,180°degree. · Straight edges, beveled edges, round edges. · Glass preparation- Mickey Mouse ear, square and round glass cut. · Glass thickness 8mm-12mm. · Glass door weight 35~36Kgs with two hinges. · Glass door weight 54Kgs with three hinges. · Also available in some models of shower door hinges with adjustable hinges. · Also available in auto- self closing for some models. · Also available in Bi-fold Hinge.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
1.The Mild steel grade are:DCO01,SPCC,Q235C,Q235D,Q235E;Q345B,Q345C,Q345E,Q345E. 2.Shipbuilding steel plate.Mainly used in ship build. The grades are:A32,AH32,A36,AH36,DH36,AH36,D32,DH32 ETC. 3.Carbon structural and high strength steel plate.Mainly used in bridges,power station equipment,lifting machinery,mining macinery and other large welding structural parts.Q460C/D/E,Q235B/C/D/E,Q609C/D/E 4.Alloy Steel Plat.Mainly used in Machinery,structure,tool,etc. 40Cr,50Mn,65Mn,15CrMo,35CrMo,42CrMo etc.
Product Name Carbon steel plate 25crmo4 alloy steel sheet price Thickness 3mm~300mm,2mm-100mm is common thickness,also can customize Width 1000~3000mm,common width is 1250mm,1500mm,2000mm,2200mm Length 1000~12000mm,can as your request cut Surface Clean,finished, blasting and painting or as your request Delivery Hot Rolled, Controlled Rolling,Normalizing,Annealing, Tempering,Quanching, Q+T Packing Steel Strapping,fixing in the Container,can customize
Product Name Carbon steel plate 25crmo4 alloy steel sheet price Thickness 3mm~300mm,2mm-100mm is common thickness,also can customize Width 1000~3000mm,common width is 1250mm,1500mm,2000mm,2200mm Length 1000~12000mm,can as your request cut Surface Clean,finished, blasting and painting or as your request Delivery Hot Rolled, Controlled Rolling,Normalizing,Annealing, Tempering,Quanching, Q+T Packing Steel Strapping,fixing in the Container,can customize
Commodity Cold rolled Steel Grade Q195,Q215,Q235,08AL,SPCC,SPCD,SPCE,SPCEN,ST12,ST13,ST14,ST15,ST16,DC01, DC03,DC04,DC05,DC06 Standard ISO,JIS,ASTM,AS EN Mechnical Commercial / Drawing / Deep Drawing /Extra Deep Drawing/Structural quality Surface treatment Chromated and oiled, and ant-ifinger Hardness Softy, half hard ,hard quality Thickness 0.12-6.0mm Width 600-1500mm Coil weight 3-8MT/Coil or as your request
Mill scale, is formed on the outer surfaces of plates, sheets or profiles when they are being produced by rolling hot iron or steel billets in rolling or steel mills. It looks like a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in color. Being produced during the reheating, conditioning and hot rolling operation for the production of steel articles, the mill scale initially adheres to the steel surface and protects it from atmospheric corrosion, provided no break occurs in this coating. From the chemical and physical analysis performed on the scrap, and according to the european environmental rules, the material has been classified as a special non dangerous waste, listed in green list In particular the mill scale can be classified as follows: Einecs (european commission no.): 266-007-8 Waste code: 10 02 10 Basel code: b 12 30 Hs code: 2619.00
We are proposing about 1000 1200 Mt/ton monthly of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag : 1. >85% Fe Average 600mm Max Fraction 2. >78% Fe Average 20-300mm Fraction The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact
Waste Specification: European Classification: E46 EWC Code: 19.01.02 Basel Code: B10 10 The material is loose steel scrap processed through an incinerating plant for domestic waste followed by magnetic separation, fragmentized into pieces and consisting partly of tin coated steel cans. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. Due to the scrap dimensions and the material conditions, this particular scrap, should be carefully evaluated first, by the end users, to confirm its adequate recovery ratio and its suitability to be re-melted in the electric arc furnace. Please feel free to contact us for further details
We are proposing about 2000tons of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag - European Code: 19.12.01 - Basel Code: B1010 - HS Code: 2619.0020 - Quantity: 2000 tons currently available - Monthly quantity: 500-1000 tons depending on production - Size: 350 1200 mm - Fe content: from 77 to 86% - C content: above 2,5-3% - Bulk density: 2,8-3,4 tons/m3 - Loading type: loose in 20 (26-27 tons on average) The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact us
Desulphurisation Slag is an iron slag derived from the desulphurisation skimming process. This material is an iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si), but has a stable chemistry with 75 -80% chemistry. The level of Fe% in the slag has been estimated by water displacement test. This material con offer competitive advantages respect other metal scraps: Price; Stable Chemistry; The material can be loaded loose in 20 heavy duty container. For further details feel free to contact us.
The Tire derived Steel or Tire Wire Scrap is a light melting scrap obtained during the shredding and granulation process of used tires. Generally 10% - 20% of the weight of an old passenger car tyre usually consists of steel. An average shredding plant produces about 100-200 MT of steel tyre wire and its quality can vary according to technology, storing and management systems adopted by the producing plants. We can provide tire wire scrap that still contains up to 20% rubber/fiber. This percentage is detected by manual separation test. The material can be loaded loose in 40 HC container. For further details, please feel free to contact us.
