Applicable material: aluminium, cast iron, stainless steel etc. Applicable size: DN25 to DN300 Applicable pressure: Low Pressure Applicable temperature:80 Design standard can according to ANSI BS JIS DIN,etc. Crate
A pinch valve is a full bore or fully ported type of control valve which uses a pinching effect to obstruct fluid flow.
Type 1: Turbine The large diameter manual valves and the valves used in high pressure applications come equipped with a reduction gear to ease the operation. Manual valves can also be fitted with a chain wheel and extended stem. Type 2: Electric actuator ELECTROMECHANICAL ACTUATORS (E) The standard electromechanical actuator types are AUMA Norm SA-series and Rotork IQ-series actuators equipped with build-in limit switches and manual handwheel. The standard voltage is 380V 50Hz, others on request. Type 3: Electromechanical actuator Electric linear actuator Electromechanical actuator with electronic positioner (EO) The standard actuators are Auma Norm SA-series with RWG, Auma Matic SAM series or Rotork IQ-series. The standard incoming signal for the electromechanical positioner is 4-20 mA. All electromechanical actuators are supplied complete with manual override. Type 4: Pneumatic actuators WIDE VARIETY OF PNEUMATIC ACTUATORS (A) The pneumatic actuator is a double acting cylinder. The standard supply pressure for the pneumatic cylinder is min. 6 bar. The cylinder size is determined according to the process line pressure. The pneumatic actuator is also available in special materials for aggressive conditions.
Technical Specifications Advantages of Woke Pinch Valve Woke pinch valve has smooth media and minimal frictional resistance without any leakage nor blockage. It is highlighted in its long service life, easy maintenance, and favorable price.
The standard electromechanical actuator types are AUMA Norm SA-series and Rotork IQ-series actuators equipped with build-in limit switches and manual handwheel. The standard voltage is 380V 50Hz, others on request. Technical specifications Size range: 15~2000mm, ~84in Pressure range: 1-10MPa, 1:2 safety factor, which means bursting pressure is 2 times higher than the operating pressure. Material of valve body DN15~200 (carbon steel, ductile� iron, aluminum alloy, stainless steel-casting process) DN250~2000 (45#steel, stainless steel welding technology ) Material of valve sleeve: NR, EPDM, CR(chloroprene rubber), NBR, butyl rubber, FPM, Hypalon rubber. Working status of pinch valve Fully-open: the full-bore elastic valve sleeve of pinch valve without any gaps & dead spots. Center closed: closed on the center line of the valve body, which avoids turbulence and abrasion, as a result, the valve sleeve becomes a smooth and enclosed venturi with self-cleaning during every operation. Fully-closed: it ensures the pinch valve is with no leakage of two ways when shut off, and the safe design of inner valve sleeve requires no maintenance of sealing elements.
The large diameter manual valves and the valves used in high pressure applications come equipped with a reduction gear to ease the operation. Manual valves can also be fitted with a chain wheel and extended stem. Technical specifications Size range: 15~2000mm, ~84in Pressure range: 1-10MPa, 1:2 safety factor, which means bursting pressure is 2 times higher than the operating pressure. Material of valve body DN15~200 (carbon steel, ductile  iron, aluminum alloy, stainless steel-casting process) DN250~2000 (45#steel, stainless steel welding technology ) Material of valve sleeve: NR, EPDM, CR(chloroprene rubber), NBR, butyl rubber, FPM, Hypalon rubber. Working status of pinch valve Fully-open: the full-bore elastic valve sleeve of pinch valve without any gaps & dead spots. Center closed: closed on the center line of the valve body, which avoids turbulence and abrasion, as a result, the valve sleeve becomes a smooth and enclosed venturi with self-cleaning during every operation. Fully-closed: it ensures the pinch valve is with no leakage of two ways when shut off, and the safe design of inner valve sleeve requires no maintenance of sealing elements.
Factories around the world that have the ability to design and manufacture large size pinch valve is very few, for example: Red Valve, FLOWROX, Jindex, and etc. As the core part of pinch valve, the rubber valve sleeve has high requirements on the manufacturing capability of the suppliers with the size increase of pinch valve. It requires not only large-scale rubber processing and vulcanization equipment, but also a mature and reliable manufacturing process of valve sleeve, which is the basis for manufacturing large-size pinch valves. We, FENGCHI , have these basic conditions to design and manufacture DN600-DN2000 large-size pinch valves maturely.
Friendly and cost effective frame pinch valves that do not compromise on good quality. We ensure that our pinch valves are manufactured to suit various applications. Valve sizes are available from 50mm to 350mm. Larger sizes are available on request. Pinch valves all over the world operate on the same principal and are manufactured with heavy material, therefore making them cumbersome to handle. Frame Pinch Valves are Built with Cost-Saving in Mind Frame pinch valves differ from the norm in the sense that they are built from lightweight materials, however, the design takes care of the body strength, and the same principal applies for the wear sleeve. Lighter built valves require less installation effort in difficult applications, less bracketing on piping, and less transport costs.
Air operated pinch valve Without actuators, cost-effective automated control valve, applicable for various kinds of demanding applications. Technical specifications Size range: 15~2000mm, -84in Actuating mode: air or liquid Operating differential pressure: 2bar Applicable Media: Powder, Slurry, Particles
Friendly and cost effective frame pinch valves that do not compromise on good quality. We ensure that our pinch valves are manufactured to suit various applications. valve sizes are available from 50mm to 350mm. Larger sizes are available on request. Pinch valves all over the world operate on the same principal and are manufactured with heavy material, therefore making them cumbersome to handle. Frame Pinch Valves are Built with Cost-Saving in Mind Frame pinch valves differ from the norm in the sense that they are built from lightweight materials, however, the design takes care of the body strength, and the same principal applies for the wear sleeve. Lighter built valves require less installation effort in difficult applications, less bracketing on piping, and less transport costs.
Open Pinch Valve The open body construction is designed for applications with relatively low pressures and low temperatures when the flowing medium is non-hazardous. The open body construction is light and it is very easy to access for service. The available valve diameters begin with 80 mm. The standard body material is mild steel, but AISI316 bodies can also be delivered upon request. The open body features with the advantage of being able to tolerate misalignment and vibration.
Pinch valve is mainly composed of valve body, bushing and actuator. Modular design for excellent interchangeability. The bushing is the only part of the pinch valve that is in contact with the medium. Keep the pinch valve and replace only the inner bushing. Get the all-new pinch valve for great rewards.
Rubber sleeve is the most important component for any type of pinch valves, it is the core of pinch valve. Rubber sleeve provides corrosion & wear resistance, and pressure bearing capacity. The quality of pinch valve is as good as the quality of its sleeve.
Control medium: compressed air Applicable temperature: 100 Acid and alkali resistance: 15% concentration; Structural type: floating straight-through type; Minimum closing pressure: 0.2Mpa; Maximum control pressure: 0.6Mpa; Flange pressure: PN10, PN16; Normal working pressure difference: 0.2 0.3Mpa; Applicable media: fibrous liquid, petroleum, pulp, cement, powder, slurry, sewage sludge; even if it is mixed with solid
The sealed body construction is designed for applications where no leakage of the flowing medium through the valve body is allowed to the environment. The PVS model has proved especially successful in high pressure applications due to the extremely resistant body construction. The sealed body can be equipped with an alarm or piping to ensure that the sleeve rupture can be noticed immediately.� The PVS structure has no rising parts outside the body. The body materials can be chosen from cast iron/mild steel, aluminium or AISI316. Technical specifications Size range: 15~2000mm, �½~84in Pressure range: 1-10MPa, 1:2 safety factor, which means bursting pressure is 2 times higher than the operating pressure. Material of valve body DN15~200 (carbon steel, ductile� iron, aluminum alloy, stainless steel-casting process) DN250~2000 (45#steel, stainless steel welding technology ) Material of valve sleeve: NR, EPDM, CR(chloroprene rubber), NBR, butyl rubber, FPM, Hypalon rubber. Working status of pinch valve Fully-open: the full-bore elastic valve sleeve of pinch valve without any gaps & dead spots. Center closed: closed on the center line of the valve body, which avoids turbulence and abrasion, as a result, the valve sleeve becomes a smooth and enclosed venturi with self-cleaning during every operation. Fully-closed: it ensures the pinch valve is with no leakage of two ways when shut off, and the safe design of inner valve sleeve requires no maintenance of sealing elements.
Product : Valves Brand : Renaissance Pipe Fitting Inc. Sizes : Refer the specification Condition : New Rating : 4.6, based on 112 reviews price : Start from 5 USD RFP India is Indias wellknown manufacturer supplier and exporter of Valves which is a device that regulates directs or controls the flow of a fluid gases liquids fluidized solids or slurries by opening closing or partially obstructing various passageways Valves are technically valves fittings but are usually discussed as a separate category In an open valve fluid flows in a direction from higher pressure to lower pressure It is being made up from different materials like Stainless Steel Carbon Steel Alloy Steel Gun Metal Brass Bronze Forge Cast Iron Cast Steel and Mild Steel Meanwhile Valves are quite diverse and may be classified into a number of basic types such as Ball Valve Butterfly valve Ceramic Disc valve Check valve Choke Valve Diaphragm valve Gate valve Globe valve Knife Valve Needle Valve Pinch Valve Piston Valve Plug Valve and so on
Many types of WCB, LCC Materal VALVE. Many types of CF8M, CF8M Material VALVE. Equipment for Oil & Gas Industries.
We supply valves� for specialized fields such as Oil & Gas, Offshore, Petrochemical, Power, Marine and General Industry. Types are Ball Valves, Gate Valve, Globe Valve, Swing NRV Valve, 3 Way Valve, Butterfly Valve, Wafer Check Valve, Disc Check Valve and Customize Valves too are in scope of supply.
Angle valve
