Penetrometer For determine semi solid to solid materials, such as grease, waxes, cosmetics, Paint. Using Penetration in the sample by a cone of definite weight (50 or 100) gms fitted to rod. By adjusting arm to touch the surface of the sample, automatic timer is also available. Centering device Dial with brass cone and container Standard : ASTMD 937, ASTMD 217, IS 1448, IP-50
Product Code Product Description PRS-ZE0665 Spring Type Proctor Penetrometer PRS-ZE0666 Needle Set for Proctor Penetrometer (28.55, 24.79, 20.22, 16.54, 12.83, 9.07, 6.40, 5.23 and 4.52 mm diameters) The PRS-ZE0665 Spring Type Proctor Penetrometer is used for establishing the moisture-penetration resistance relation of finegrained soils. The apparatus consists of a spring loading device which is graduated from 10 to150 lbf in 2 lbf subdivisions. Needle Set for Proctor Penetrometer consist of interchangeable needle points of 28.55, 24.79, 20.22, 16.54, 12.83, 9.07, 6.40, 5.23, 4.52 mm diameters and a carrying case. Dimensions 540x260x60 mm (packed) Weight (approx.) 5 kg
Standard: ASTM D 6951-03 This portable hand operated equipment is designed to obtain a direct and rapid in-situ evaluation of the structural strength of road pavement layers constructed with unbound materials. The test is performed with continuous penetrations at approx. 800 mm depth with max. depth of 2 m by using extension rods.
It is suitable to make needle penetration determination for highway asphalt, modified asphalt, as well as residue of liquid petroleum asphalt or emulsified asphalt after evaporation. Standard : EN 1426, ASTM D5, AASHTO T49
Product Code Product Description PRS-ZE0095 Dynamic Cone Penetrometer (DCP) STANDARDS : The PRS-ZE0095 Dynamic Cone Penetrometer is used for the rapid, in situ measurement of structural properties of existing road pavement constructed with unbound materials. it incorporates an 8 kg weight dropping through a height of 575 mm and 60° cone having a diameter of 20 mm. with the standard DCP measurements can be made down to a depth of approximately 850 mm or when extension shafts are used to a recommended maximum depth of 2 m. Readings are usually taken after a set number of blows, changing the number according to the strength of the layer being penetrated. A typical test takes only a few minutes, therefore the instrument provides a very efficient method of obtaining information that would normally require the digging of test pits. The penetration hammer assembly consists of 8 kg hammer, hammer shaft, anvil with plastic plate coupling for ruler and handle. The Dynamic Cone Penetrometer is supplied complete with; � A hammer assembly, � Penetration rod, � 2 piece 60° cone, � Metal plate coupling for ruler, � Segmented adaptor for extension rods, � Segmented upper extension rod, � Segmented lower extension rod, � 2 piece 13-17mm AF spanners, � 3mm AF hex wrench, � Tommy bar, � A bottle of adhesive,10cc, � Users Manual � Steel ruler, � Carrying Case, heavy-duty wooden
Features 1. It can allow the test in a different direction, and can even be used in a constant temperature water bath; 2. With digital display depth measuring mechanism, easy to use, good repeatability and high accuracy; 3. Bracket move fast and fretting two kinds of speed, ease of test operation of the tip of the needle at the surface of the sample; 4. It has a table level adjusting mechanism, and easy to adjust; 5. With manual release pin into pieces of bodies, to ensure that in the not automatically controlled release, still normal operation.
Product Code Product Description PRS-ZE0180 Semi-Automatic Penetrometer for Liquid Limit, 220-240 V 50-60 Hz PRS-ZE0180/110 Semi-Automatic Penetrometer for Liquid Limit,110 V 60 Hz PRS-ZE0182 Liquid Limit Penetration Test Cone 30° Angle,Stainless Steel PRS-ZE0183 Cone Test Gauge for PRS-ZE0182 PRS-ZE0184 Liquid Limit Penetration Test Cone 60° Angle,Stainless Steel PRS-ZE0185 Cone Test Gauge for PRS-ZE0184 PRSGH-1425 Moisture Content Tin with Lid �:55 mm x h:35 mm, Aluminum PRSGH-1435 Moisture Content Tin with Lid 75 mm x h:50 mm, Aluminum A Cone Penetrometer is used to determine the moisture content at which clay soils pass from a plastic to a liquid state, and used also for the determination of undrained shear strength. The PRS-ZE0180 Semi-Automatic Penetrometer for Liquid Limit consists of a cast iron base with course and fine leveling screws, a digital penetration measurement gauge 0.01 mm resolution/readibility and an automatic penetration timer unit. The PRS-ZE0180 is equipped with a digital, 99 second timer, which can be set to the standard 5 second free-fall time or to some other setting for customized tests. When engaged the timer will allow the needle to free fall into the sample for the specific time interval and then lock the needle from advancing while providing a direct reading of the test results. 320 g weight should be added to the 30° angle cone to get a total weight of 400 g for the shear strength test. Semi-Automatic Penetrometer for Liquid Limit supplied complete with; � Automatic Penetration Timer Unit, � 30° Penetration Cone � Sample Cups, 3 pcs. Aluminium, �55 mm x h:35 mm.
Product Code Product Description PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer 220-240 V 50-60 Hz PRS-AS0120/110 Semi-Automatic Digital Bitumen Penetrometer 110 V 60 Hz PRS-AS0121 Transfer Dish for PRS-AS0120 PRS-AS0122 Sample Cup, � 55x35 mm, stainless steel PRS-AS0123 Sample Cup, � 70x45 mm, stainless steel PRS-AS0124 Penetration Needle, 2,5 g PRS-AS0160 One-Quarter Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126 PRS-AS0161 One-Half Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126 PRS-AS0162 Penetrometer Cone ASTM D 217 (Optional Type) and ASTM D 937, for PRS-AS0120 and PRS-AS0126, Brass PRS-AS0165 Resilience Ball Penetration Tool. ASTM D5329, for PRS-AS0120 and PRS-AS0126 STANDARDS : EN 1426; ASTM D5; AASHTO T49 The PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer is used to determine the penetration of bituminous samples under constant load, time and temperature. The Penetrometer consists of a cast iron base with coarse and fine levelling screws, a digital penetration measurement gauge 0.01 mm readability and a penetration timer unit. Start button of the penetration timer unit is used to release the plunger fitted with the needle to start the 5 seconds test. A water bath (PRSGE-AS4000 or PRSGE-AS4050, 25±0,1 C) and a thermometer ( IP38, ASTM 17C or 63C ) required for the test should be ordered separately. The Semi-Automatic Digital Bitumen Penetrometer is supplied complete with; � Penetration Needle, 2,5g, 1 pieces � Transfer Dish � Sample Cup � 55x35 mm, 3 pieces, stainless steel Dimensions 200x300x500 mm Weight (approx.) 16 kg
Compression testing machine used for testing the strenght of cement and concrete 900mm * 500 mm, 200 kg
Test sieves made from brass sheet with stainless steel perfoted square holes 200mm * 200mm ; 800 grams ;
Soil Testing Equipment Digital Triaxial Testing Machine. Autolevel Consolidometer. Bishop pore pressure apparatus. Coarse Sieves. Cone Penetrometer. Consolidation Test Apparatus. Constant Oil and Water Pressure Apparatus. Digital C.B.R. Apparatus.
All kinds of scientific and soil testing instruments, laboratory jaw crusher, vicat needle apparatus, masta gauge, industrial moulds, standard penetrometer, core cutting and core drilling machine, slump test apparatus, laboratory pulveriser, rapid moisture meter, aggregate impact tester, fatigue testing machine.
Concrete compression test machine, cement compression test machine, cylinder concrete sample mould, cube mould, concrete pan mixer, flakiness and length gauge apparatus water bath, mortar flow table, ve-be, mortar mixer, concrete air meter, sieve shaker, soil compactor, penetrometer, cbr test apparatus, sand density cone apparatus, aggregate impact test machine, los angeles testing machine, abrasion testing machine, servo hydraulic testing machine, vibrating table, sand equivalent test set, ductility testing machine, digital cbr, core drilling machine, drying oven, digital thermometer, asphalt compaction, asphalt penetrometer, point loading test machine, centrifuge extractor, cement beam mold, sieve set, cement cubic mold, saybolt viscometer, dynamic penetrometer, cement comparator, asphalt oven, hot plate, thermometeres, surface thermometers, soil laboratory equipment, asphalt bitumen laboratory equipment, general measuring laboratory equipme.
Static cone penetrometer, CBR(california bearing ratio), consolidation apparatus, unconfined compression tester, liquid limit tester, direct shear apparatus, vane shear apparatus, triaxial test for soil, automatic compactor for soil, sieve shaker, wet sieve shaker, soil lathe motorised, front loading odometer, cement tensile testing machines, flexure strength testing machine, jaw crusher, gillmore needle apparatus, jolting apparatus, laboratory ball mill, laboratory cement autoclave, le chatlier flask.
Oil, Refrigerated Centrifuge, Bod Incubator, Flash Point Tester , Water Bath, Hot Air Oven , Muffle Furnace, Ring And Ball Tester, Pour Point Bath, Copper Corrosion Bath, Silver Corrosion Bath, Penetrometer, Viscosity Meter, Kinematic Viscosity Meter Bath, Reid Vapour Pressure Tester, Foaming Characteristics Bath, Lpg Corrosion Bath And Bomb Kit, Thin Film Oven, Double Distillation Astm D86, Redwood Viscometer, Saybolt Viscometer, Freezing Point Tester, Crm, Certified Reference Material, Digital Temperature Humidity Pressure Display, Mercury Barometer, Filtration Kit Orsat Assembly And Glassware.
Product Code Product Description PRS-ZE0080 Field Inspection Testing Kit PRS-ZE0082 Field Inspection Pocket Vane Tester PRS-ZE0082/1 Extension Rod for PRS-ZE0082 PRS-ZE0084 Heavy Duty Pocket Penetrometer, 0-10 kgf/cm2 STANDARDS : ASTM D2573 The PRS-ZE0080 Field Inspection Testing Kit is ideal for geotechnicians, geologists and agronomists. It consists of the PRS-ZE0084 Pocket Penetrometer and of the PRS-ZE0082 Field Inspection Pocket Vane Tester. The instrument is contained in a practical carrying case. PRS-ZE0080 Field Inspection Testing Kit Dimensions (packed) 240x210x50 mm Weigth (approx.) 1.8 kg The PRS-ZE0082 Field Inspection Pocket Vane Tester is especially designed to measure the undrained shear strength (CU) of cohesive soils, consists of a cylindrical body with a torsional spring and three interchangeable vanes of different sizes used depending upon the expected strength of the soil. The height/diameter ratio of all vanes is 2. During operation the vane is driven for 5-6 cm into the soil and then turned with the handle. Deep measures (i.e. on the top of undisturbed samples) can be obtained using the extension rod. All stainless steel construction. Supplied in a plastic case. Extension rod should be ordered separately. PRS-ZE0082 Field Inspections Pocket Vane Tester Vane Dimensions (height x dia.) 32x16; 40x20, 50.8x25.4 mm Measuring Range 0 to 240 kPa (0-24 N/cm') Torque Value 5 N - m Extension Rod 500 mm depth. Overall Dimensions (assembled) 310x105 mm Weight 1.3 kg The PRS-ZE0084 Heavy Duty Pocket Penetrometer is designed for making field classification of cohesive soils in terms of consistency, shear strength and approximate unconfined compressive strength. Heavy duty model is all stainless steel construction, three interchangeable tips: 4.5 mm dia. for very hard soil, 6.35 mm for medium and soft soil, 8.98 mm for soft soil. Supplied complete with plastic case. PRS-ZE0084 Heavy Duty Pocket Penetrometer Measuring Range 0 to 10 kgf/cm' Dimensions (assembled) 210 mm length x 20 mm dia. Weight (approx.) 0.5 kg
Description Volleyball Sand (silica sand) If you are looking for high-quality, blended sand for volleyball court, you should look at BMS FACTORIES silica sand. BMS FACTORIES sand offers fantastic penetrometer and infiltration rates, allowing the sand to drain quickly, avoid compaction, and improve playability. Volleyball Sand (silica sand) When BMS FACTORIES manufacturing volleyball sand, our factories ensure the sand is clean, washed, and ground to meet sand court specifications. You can rest assured knowing that we deliver only the highest quality, most consistent sand to our volleyball clients and facilities. Whether youâ??re building a new sand volleyball court from scratch, or simply need to revitalize your existing court, weâ??re here to help. For more information on finding the best volleyball sand for your court and to receive a quote, please contact us . Sand has become a passion of ours due to the fact that we have seen so many beautiful volleyball courts over the years with horrible sand. Building a beach volleyball court with bad sand typically results in a court which doesnot get used. Most volleyball players new and experienced donot like to play beach volleyball in a cloud of dust or in sand that cuts up their knees and elbows. You will want to deposit one to two feet of volleyball sand over the area prepped for drainage and rake level. Your budget may dictate the depth of sand used but keep in mind if you go with a lesser depth, plan on raking or shoveling back sand from the middle of your dished out court to the sides about once a week or more (depending on how often the court is used). The playing area alone will consume approximately 100+ tons of sand at a depth of approximately 12 inches. Many customers purchase between 100-300 tons per court depending on the size of their court and the depth they prefer. ( For more detailed information and pricing) Fast Delivery From Our Strategic Locations in Saudi Arabia
Scope This instrument conforms to GB/T4509, GB/T269, ASTMD217, JTJ052-2000, T0604 and other related standards. It is suitable to determine needle penetration of asphalt and cone penetration of grease. The instrument can also be used to test food ingredients solid granules, powders, gels, body frozen and other materials, as well as cheese, sugar gum, butter, wheat its pouring, butter, fermented the like, in the food industry, highway traffic engineering and other industries department can be widely used. Features 1. It integrates new design concepts about penetrometer all over the world. It is advanced and delicate. 2. It can make determination for needle penetration and cone penetration. 3. It controlled by a computer, it can measure the needle penetration and cone penetration automatically. The test data are accurate and reliable. 4. The newly designed up and down assembly can be adjusted freely. 5. Equipped with automatic temperature controlling device and magnetic stirrer, so the bath temperature is uniform with high temperature controlling accuracy. 6. All parameters are shown on the LCD in real time. 7. Equipped with a micro-printer, so it can print out test data. 8. It has a computer communication port to communicate with a computer. Technical Parameters 1. Measurement range: 0~600 penetrations; 2. Resolution: 0.1 penetrations; 3. Timing selection: 0~60 s; Timing error is less than ±0.1 s; 4. Heating power: 200 W; 5. Temperature controlling accuracy: 25±0.1 °C; (the Ambient temperature should not be higher than 20 °C); 6. Data storage: 30 groups; 7. Constant temperature bath: made of harden glass; 8. Stirrer: a magnetic stirrer; 9. Standard needle: 2.5±0.05g; as per GB/T4509, and T0604; 10. Up and down holder: it contains fine adjustment and coarse adjustment assembly to let needle tip just contact with sample surface; 11. Power supply: AC 220V±10%, 50 Hz; 12. Memory function: it can save 30 groups of test data;
