New Energy Hydrogen Porous Titanium Plate Suppliers and Manufacturers

The raw material of the porous titanium plate for hydrogen production by PEM water electrolysis is pure titanium powder, formed by pressing the mold and sintered at high temperature in a vacuum. Product Parameters Filtration accuracy: 0.5um-50um Porosity: 30-40% Permeability: 3-800m3/m2hkPa Compressive strength: 2-3Mpa Temperature resistance: 300â?? Maximum working pressure difference: 0.6Mpa Features 1. Strong temperature resistance, typical application at temperatures below 300 C;High filtration precision, stable pores, can effectively remove suspended solids and particles, etc., and the purification effect is good; 2. Good air permeability and low pressure loss. High porosity, uniform pore size, low initial resistance; 3. Easy to blow back, can be regenerated online, easy to clean, strong regeneration ability, long service life; 4. High mechanical strength, good rigidity, good plasticity, no need for additional skeleton support protection, easy to install and use; 5. Easy maintenance, good assembly, can be welded, bonded and machined; 6. Uniform pores, especially suitable for occasions requiring high uniformity such as fluid distribution and homogenization treatment; 7. Good corrosion resistance, can be used in nitric acid, sulfuric acid, acetic acid, oxalic acid, phosphoric acid, 5% hydrochloric acid, molten sodium. Stable use in liquid hydrogen, liquid nitrogen, hydrogen sulfide, acetylene, water vapor, hydrogen, carbon dioxide gas and other environments.

Product Introduction Ultra-thin 0.6mm titanium porous transfer layer for hydrogen has a wide range of applications in hydrogen industry. In the hydrogen industry, these plates are used for hydrogen purification and separation, and they are an important component in many hydrogen-based technologies. Ultra-thin 0.6mm titanium porous transfer layer for hydrogen has good electrical conductivity, gas permeability, liquid permeability and chemical stability. In electrochemical systems such as fuel cells, the application of porous titanium plates can improve the energy conversion efficiency and stability of electrochemical systems, thereby promoting the development and application of electrochemical systems. Parameters Material: Gr1 titanium powder Purity: 99.6% Thickness:0.6mm Size: customized Application: PTL GDL in PEM electrolyzer Porosity: 35% Pore size: 20um Features High conductivity: Titanium is a good conductive material, and the porous titanium plate has excellent conductivity and can effectively transport electrons. High gas permeability: The porous titanium plate can control the parameters such as pore size and porosity to make it have high gas permeability, so that it can effectively transmit gases such as hydrogen and oxygen. Good liquid permeability: The pore structure of the porous titanium plate can control the transmission of liquid, so that it has high liquid permeability. High chemical stability: Titanium has good chemical stability and can operate stably for a long time in acidic or alkaline environments. Applications Hydrogen energy industry Gas filtration Oil and liquid filters Muffler Fuel Industry Catalyst filtration Package and Shipment 1. Sintered Filters are usually packed in cartons, wrapped in soft film, and fixed in a box filled with industrial foam cotton, and the outer baler is packed with plastic bags with no damage during transportation. 2. Wooden box export packaging can also be customized. The foam cotton can be filled and fixed, the external box is sealed, the bottom is specified, the whole packaging is processed, and the goods can be delivered to the customer's designated place without damage.

The production of PTL (porous titanium sintered plate) is a key component in the manufacture of hydrogen production electrolyzers. PTL is a type of electrode material that is used to catalyze the reaction that produces hydrogen gas from water. The parameters of PTL (porous titanium sintered plate) used in hydrogen production electrolyzers can vary depending on the specific application and design of the electrolyzer. However, some common parameters for PTL porous titanium sintered plates used in hydrogen production electrolyzers include: 1.Porosity: The porosity of the PTL porous titanium sintered plate is an important parameter that determines the surface area available for the hydrogen production reaction. Typically, PTL plates have a porosity of around 30-50%, which provides a large surface area for efficient hydrogen production. 2.Pore size: The size of the pores in the PTL plate can also affect the efficiency of the hydrogen production reaction. Generally, PTL plates have pore sizes ranging from 1um to 100um, depending on the specific application. 3.Thickness: The thickness of the PTL plate can vary depending on the design of the hydrogen production electrolyzer. TopTiTech can customized the thickness from 1mm to 3mm. 4.Catalyst loading: The amount and type of catalyst material used to coat the PTL plate can also affect the efficiency of the hydrogen production reaction. Typically, platinum or iridium catalysts are used, with loading levels ranging from a few micrograms per square centimeter to several milligrams per square centimeter.

The raw material of the porous titanium plate for hydrogen production by PEM water electrolysis is pure titanium powder, which is formed by pressing the mold and sintered at high temperature in vacuum. Hydrogen production by water electrolysis is a new energy pillar sunrise industry. The micropore diameter of the porous titanium plate is used to fully react with the medium to produce hydrogen energy. The surface is coated to prevent oxidation and increase the efficiency of hydrogen production. Porous titanium plates are widely used in hydrogen energy, petrochemical, and pharmaceutical filtration, with obvious advantages, and are indispensable products. Product Parameters Filtration accuracy: 0.5um-50um Porosity: 30-40% Permeability: 3-800m3/m2hkPa Compressive strength: 2-3Mpa Temperature resistance: 300 Maximum working pressure difference: 0.6Mpa Features 1. Strong temperature resistance, typical application at temperatures below 300 C;High filtration precision, stable pores, can effectively remove suspended solids and particles, etc., and the purification effect is good; 2. Good air permeability and low pressure loss. High porosity, uniform pore size, low initial resistance; 3. Easy to blow back, can be regenerated online, easy to clean, strong regeneration ability, long service life; 4. High mechanical strength, good rigidity, good plasticity, no need for additional skeleton support protection, easy to install and use; 5. Easy maintenance, good assembly, can be welded, bonded and machined; 6. Uniform pores, especially suitable for occasions requiring high uniformity such as fluid distribution and homogenization treatment; 7. Good corrosion resistance, can be used in nitric acid, sulfuric acid, acetic acid, oxalic acid, phosphoric acid, 5% hydrochloric acid, molten sodium. Stable use in liquid hydrogen, liquid nitrogen, hydrogen sulfide, acetylene, water vapor, hydrogen, carbon dioxide gas and other environments. Applications The porous titanium plate is used as the GDL (gas diffusion layer) of the anode for hydrogen production by water electrolysis in PEM water electrolysis. The pores are uniform and the porosity can be controlled at 30%-40%. Good electrical conductivity and strong corrosion resistance. It can be coated with platinum group metals to enhance its catalytic performance. The cost is relatively high, but the hydrogen production efficiency is high and the purity is high, which is suitable for industrial hydrogen production. Every kind of filter material will be blocked, so it is very important to choose the pore size. If you choose the right pore size, you will have a good filtration efficiency, and the blocking situation will be alleviated. If the blockage is serious, regular replacement can solve this problem.

Sheet :Thickness:0.6-10mm Max Length:1000mm Max width:340mm Pipe : OD10-150MM* wall thickness 2-5MM Materials : titanium GR1 GR2 Feature: 1.Working Temperature:-200-1000°C 2.Corrosion Resistance 3.High Filtering Efficiency 4.Metallic capacities, such as noise reduction,hot resistance,heat conduction,high strength and etc 5.Easy to welding and long working life Filter Shape: Could be cartridge filters,disc filters ,cup filters,cap filters,filter palte and etc Application: separation and purification of solid-liquid, gas-liquid and gas-solid in the petrifaction, hydraulic manufacturing and medical apparatus and instruments of basic industries. Technique parameters titanium powder sintering filter element technique parameters using temperatur:â?¤300°C filtering level filtration precision um maximum diameter um permeability coefficient 10-12m2 permeability m3/h.m2.kpa thickness mm compression strength Mpa/cm3 T9 0.2 2.5 1.5 0.6-10 3 T8 0.5 4 3 0.6-10 3 T7 1 6 5 0.6-10 3 T6 2 10 15 0.6-10 3 T5 5 15 0.04 40 0.6-10 2.5 T4 10 30 0.15 120 0.6-10 2.5 T3 20 60 1.01 250 0.6-10 2.5 T2 30 100 2.01 500 0.6-20 2.5 T1 50 160 3.02 800 0.6-20 2.5 The product performance can achieve and even exceed GB. The internal pressure of powder rolled and roll tube welding is more than 0.3Mpa

Mainly used in separation and filtration petrochemicals, liquid drug manufacturing, medical equipment, and other fields. Material: titanium Specifications:max.Width 340mm, max.Length 1000mm, max.Thickness 3.0mm Precision:0.2 to 65um

Product Introduction Sintered porous titanium plates are a form of material made from titanium powder that has been heated and crushed to produce a particularly porous and light structure. These plates have a high strength-to-weight ratio and are resistant to corrosion and wear. Sintered porous titanium plates are used in various applications where a high level of strength and durability is required, such as in the aerospace, automotive, and medical industries. Parameters Material: Titanium Porosity: 30%-40% Pore size: 1um-50um Thickness: above 1mm Dia: 1MM above Features 1. High Strength-to-Weight Ratio: Sintered porous titanium plates have a high strength-to-weight ratio, which means they are strong and durable while also being lightweight. This makes them ideal for applications where weight is critical, such as in the aerospace industry. 2. Corrosion Resistance: Titanium is highly resistant to corrosion, making it ideal for use in harsh environments where other materials may corrode or degrade over time. This makes sintered porous titanium plates a good choice for applications in the chemical and petrochemical industries. 3. Biocompatibility: Titanium is biocompatible, which means it is not toxic to living tissue and does not cause adverse reactions when implanted in the human body. This makes sintered porous titanium plates ideal for medical applications such as implants and prosthetics. 4. Customizable Pore Size and Distribution: Sintered porous titanium plates can be customized to have specific pore sizes and distributions, which makes them useful for applications such as filtration and catalysis. 5. High-Temperature Resistance: Titanium has a high melting point and can withstand high temperatures, making it ideal for use in high-temperature applications such as heat exchangers and furnace components. Processing The processing of sintered porous titanium plates involves several steps. First, the high purity of titanium powder will be sieved and then molded and pressed into a desired shape. Then the material is heated in a furnace to sinter the titanium particles together to form a solid structure. The final product is then machined to the desired shape and size.

Sintered porous titanium plates are a form of material made from titanium powder that has been heated and crushed to produce a particularly porous and light structure. These plates have a high strength-to-weight ratio and are resistant to corrosion and wear. Parameters Material: titanium Porosity: 30%-40% Pore size: 1um-50um Thickness: above 1mm DI: 1MM above Features 1.High Strength-to-Weight Ratio. 2.Corrosion Resistance. 3.Biocompatibility. 4.Customizable Pore Size and Distribution. 5.High Temperature Resistance. Application Chemical Industry: Sintered porous titanium plates are used in chemical processing equipment, such as filters and catalysts, due to their resistance to corrosion and customizable pore size. Medical Industry: Sintered porous titanium plates are used in medical implants and prosthetics such as bone substitutes and dental implants� due to their biocompatibility, strength, and durability. Energy Industry: Sintered porous titanium plates are used in fuel cells and batteries due to their high strength-to-weight ratio and ability to conduct electricity. Environmental Industry: Sintered porous titanium plates are used in water treatment systems and air filters due to their customizable pore size and distribution and resistance to corrosion. Processing The processing of sintered porous titanium plates involves several steps. First, the high purity of titanium powder will be sieved and then mold pressed into a desired shape. Then the material is heated in a furnace to sinter the titanium particles together to form a solid structure. The final product is then machined to the desired shape and size.

Product Introduction A porous titanium plate is a type of material made from titanium that has many small holes or pores throughout its surface. These pores can range in size from a few micrometers to several millimeters, depending on the manufacturing process and the intended use of the plate. Porous titanium plates are commonly used in a variety of applications, includingbiomedical implants, filtration systems, and catalytic converters. One of their most important properties is their high surface area-to-volume ratio, which allows for efficient mass transfer and gas exchange. Parameters Material: titanium sponge Porosity: 35% Filtration rate: 0.22mm- 100mm Thickness: above 1mm Size: square round and customized with the drawing How is the porosity of the plate controlled during manufacturing The porosity of aporous titaniumplate can be controlled during the manufacturing process. In the powder sintering process,titanium powderis compressed and heated to a temperature just below the melting point of titanium. The powder particles then fuse together to form a solid plate with a controlled porosity. The porosity of the plate can be controlled by adjusting the size and shape of the powder particles, the temperature and pressure of thesintering process, and the amount of binder material used.

A porous titanium plate is a type of material made from titanium that has many small holes or pores throughout its surface. These pores can range in size from a few micrometers to several millimeters, depending on the manufacturing process and the intended use of the plate. Porous titanium plates are commonly used in a variety of applications, including biomedical implants, filtration systems, and catalytic converters. One of their most important properties is their high surface area-to-volume ratio, which allows for efficient mass transfer and gas exchange. Parameters Material: titanium sponge Porosity: 35% Filtration rate: 0.22mm- 100mm Thickness: above 1mm Size: square round and customized with the drawing Features Versatile pore structure: The pore structure of porous sintered titanium plates can be varied to achieve different properties. For example, plates with a larger pore size may have a higher permeability, while plates with a smaller pore size may have a higher particle retention. Customized shape and size: Porous sintered titanium plates can be manufactured in a variety of shapes and sizes to suit specific application requirements. This allows for customized designs that can optimize performance and minimize material waste. Environmental sustainability: Porous sintered titanium plates can be recycled and reused, making them an environmentally sustainable choice. Additionally, the manufacturing process can be optimized to minimize waste and energy consumption. Applications in energy production: Porous sintered titanium plates can be used in energy production applications such as fuel cells and batteries. The high surface area-to-volume ratio of the plates allows for efficient gas exchange and can enhance the performance of these devices. Applications Porous titanium plates are commonly used in a variety of applications, including biomedical implants, filtration systems, and catalytic converters. One of their most important properties is their high surface area-to-volume ratio, which allows for efficient mass transfer and gas exchange. In biomedical applications, porous titanium plates are often used as bone implants or scaffolds to promote bone regeneration. The porous structure of the plate allows for the growth of new bone tissue into the implant, which can help to repair or replace damaged bones. In filtration systems, porous titanium plates can be used as a high-performance filter media due to their ability to trap and remove small particles and impurities from fluids. In biomedical applications, porous titanium plates are often used as bone implants or scaffolds to promote bone regeneration. The porous structure of the plate allows for the growth of new bone tissue into the implant, which can help to repair or replace damaged bones.

Product Introduction Sintered porous titanium plate is a porous material made of titanium powder that is compressed and heated to create a solid block. The block is then treated with acid or other chemicals to remove any remaining impurities and create a porous structure. Product parameters Aperture size: 0.1 3mm Porosity: 30% 60% Thickness: 0.5mm 6mm Specific surface area: 100 1000m2/m3 Tensile strength: 300 600MPa Thermal conductivity: 2 20W/mK Application fields: widely used in aviation, automobiles, medical equipment, biological materials, filter materials and other fields Features 1. Efficient transmission of hydrogen: The highly porous structure of the porous titanium plate enables the effective transmission of hydrogen and has good gas transmission performance, which can significantly improve the efficiency of the water electrolysis hydrogen production system. 2. Lightweight and corrosion-resistant: The porous titanium plate is light in weight and is very suitable for making the transmission layer. At the same time, the titanium material can resist the corrosion of many acidic and alkaline media and has a long life and stable performance. 3. Easy to clean: The porous titanium plate has a large opening rate and a large surface area, which is easy to clean and handle, and can effectively reduce the pollution of the water electrolysis hydrogen production system and reduce the impact on the environment. 4. Highly stable: The porous titanium plate has a long service life and high stability, and can keep its pore structure and performance unchanged, further improving the stability of the hydrogen production system, thereby meeting various needs of industrial and scientific laboratories.

Sintered porous titanium plate is a porous material made of titanium powder that is compressed and heated to create a solid block. The block is then treated with acid or other chemicals to remove any remaining impurities and create a porous structure. Product parameters Aperture size: 0.1~3mm Porosity: 30% 60% Thickness: 0.5mm 6mm Specific surface area: 100 1000m2/m3 Tensile strength: 300 600MPa Thermal conductivity: 2 20W/mK Application fields: widely used in aviation, automobiles, medical equipment, biological materials, filter materials and other fields Features 1. Efficient transmission of hydrogen: The highly porous structure of the porous titanium plate enables the effective transmission of hydrogen and has good gas transmission performance, which can significantly improve the efficiency of the water electrolysis hydrogen production system. 2. Lightweight and corrosion-resistant: The porous titanium plate is light in weight and is very suitable for making the transmission layer. At the same time, the titanium material can resist the corrosion of many acidic and alkaline media, and has a long life and stable performance. 3. Easy to clean: The porous titanium plate has a large opening rate and a large surface area, which is easy to clean and handle, and can effectively reduce the pollution of the water electrolysis hydrogen production system and reduce the impact on the environment. 4. Highly stable: The porous titanium plate has a long service life and high stability, and can keep its pore structure and performance unchanged, further improving the stability of the hydrogen production system, thereby meeting various needs of industrial and scientific laboratories. other apps 1. Medical field: Porous titanium plate has good biocompatibility and mechanical properties, and is widely used in medical fields such as orthopedics and dentistry, as artificial bone and dental implants. 2. Energy storage field: The large surface area and pore structure of porous titanium plates make them potential applications in capacitors, which can be used in the manufacture of electronic devices such as batteries and capacitors. 3. Sewage treatment field: The high specific surface area and good catalytic performance of porous titanium plates can be used in the field of sewage treatment, such as the oxidative degradation of organic wastewater and the adsorption of metal ions. 4. Environmental field: Porous titanium plates can be used to clean harmful gases and odorous substances in the atmosphere, and can also be used in environmental protection fields such as seawater desalination and water resource utilization. 5. Aerospace field: The lightweight and high strength of porous titanium plates can be used in the aerospace field, such as manufacturing aircraft, satellites and other components.

As a new type of green energy, hydrogen energy is a new type of green energy, and its sustainable manufacturing has become the goal of the industry. Water electrolysis hydrogen production, hydrogen generators, etc., hydrogen energy equipment emerge in endlessly, and relatively safe and efficient hydrogen production consumables have become a relative key. Product parameters Brand: TOPTITECH Material: Gr1 Shape: Rectangular Applicable object: electrolyzer Thickness: 0.8-2.0mm Specifications: can be customized Mesh: 1000 mesh/inch Filtration accuracy: 20 microns Type: Efficient Performance: acid resistance; alkali resistance; high temperature resistance Uses: water, gas, liquid Features 1. Precise air permeability, uniform air holes, certain mechanical strength, high adaptability for external processing; 2. High-purity raw materials, resistant to various acid and alkali environments, a corrosion-resistant material; 3. The porosity can reach 35%, which is a relatively high-strength product in a breathable material and can bear pressure; 4. It can withstand a certain temperature, for example, it can be used normally in a long-term heating environment within 300 degrees. Applications 1. Decarbonization filtration in the concentrated preparation link of the pharmaceutical industry and security filtration before terminal filtration in the thin preparation link. 2. Filtration, decarbonization filtration, and fine filtering of materials used in the manufacturing of raw materials. 3. Filtration following ozone sterilizing and ozone aeration, as well as security filtration for water treatment industries RO, EDI, and ultrafiltration systems. the 4. Clarify and filtering of alcohol, beer, soy sauce, vegetable oil, mineral water, and other drinks and food. 5. Material purification and sintered porous titanium plate at the feed inlet, decarbonization filtration and precision filtration of liquid products, liquid raw materials, and pharmaceutical intermediates in the chemical industry, filtration and recovery of ultra-fine fine bodies and catalysts, precision filtration and system heat conduction after resin adsorption Impurity removal and filtration of oil and materials, catalytic gas purification, etc. the 6. Before reverse osmosis in the seawater desalination field, oilfield return water filtering and security filtration. 7. White clay filtration and high-temperature decarbonization in the dye business. 8. Steam, compressed air, and catalytic gas purification and filtration are the primary aspects of gas purification. Process The pure titanium powder is pressed into a plate shape, and then sintered in a high-temperature vacuum sintering furnace. The particles are naturally bonded to form a plate shape, and then cooled to form a plate base material, which can then be cut into the desired shape.

Porous titanium plate is a type of material that is characterized by its interconnected network of pores. It is made from titanium, which is a lightweight, strong, and corrosion-resistant metal. The porosity of the titanium plate allows for increased surface area, which can be useful in applications such as filtration, catalysis, and biomedical implants. Product Parameters Brand: TOPTITECH Porosity: 30-40% Filtration rate: 1um-50um Temperature: â?¤300â?? Size: Customized Porous titanium plate has several features that make it a unique material. First, the pore size and distribution can be controlled during manufacturing, allowing for customization of the material for specific applications. The interconnected network of pores also allows for fluid or gas flow through the material, making it useful for filtration and catalysis. Porous titanium plate is also biocompatible, which makes it suitable for use in biomedical applications. Porous titanium plate has a wide range of applications in various industries. In biomedical applications, it is commonly used for bone implants, where the porous structure allows for better integration with surrounding bone tissue. It is also used in dental implants, where the porous structure allows for better anchoring of the implant. In the chemical industry, porous titanium plate is used for catalysis, where the high surface area and pore structure allow for efficient chemical reactions. It is also used in filtration applications, such as air and water filters. Porous titanium plate can be manufactured using several techniques, including powder metallurgy, sintering, and electrochemical deposition. In powder metallurgy, titanium powder is mixed with a binder material and then pressed into a desired shape. The material is then sintered to remove the binder and fuse the titanium particles together. In electrochemical deposition, a layer of titanium is deposited onto a substrate using an electrochemical process. The resulting layer can be made porous by controlling the deposition parameters.

Porous titanium plate is a type of material that is characterized by its interconnected network of pores. It is made from titanium, which is a lightweight, strong, and corrosion-resistant metal. The porosity of the titanium plate allows for increased surface area, which can be useful in applications such as filtration, catalysis, and biomedical implants. Product Parameters Brand: TOPTITECH Porosity: 30-40% Filtration rate: 1um-50um Temperature: â?¤300â?? Size: Customized Porous titanium plate has several features that make it a unique material. First, the pore size and distribution can be controlled during manufacturing, allowing for customization of the material for specific applications. The interconnected network of pores also allows for fluid or gas flow through the material, making it useful for filtration and catalysis. Porous titanium plate is also biocompatible, which makes it suitable for use in biomedical applications. Porous titanium plate has a wide range of applications in various industries. In biomedical applications, it is commonly used for bone implants, where the porous structure allows for better integration with surrounding bone tissue. It is also used in dental implants, where the porous structure allows for better anchoring of the implant. In the chemical industry, porous titanium plate is used for catalysis, where the high surface area and pore structure allow for efficient chemical reactions. It is also used in filtration applications, such as air and water filters. Porous titanium plates can be manufactured using several techniques, including powder metallurgy, sintering, and electrochemical deposition. In powder metallurgy, titanium powder is mixed with a binder material and then pressed into a desired shape. The material is then sintered to remove the binder and fuse the titanium particles together. In an electrochemical deposition, a layer of titanium is deposited onto a substrate using an electrochemical process. The resulting layer can be made porous by controlling the deposition parameters.

In a proton exchange membrane fuel cell, the main function of the gas diffusion layer is to support the catalyst and provide a channel for the gas participating in the reaction and the water generated. It is one of the key components of the membrane electrode. The porous titanium plate has a good and uniform large number of pores, the porosity can be controlled by adjusting the diameter of the powder, and it is made of sintering, high temperature resistance and corrosion resistance. Product Parameters Color: Metallic Shape: Square plate, disc, can be customized Process: Powder sintering Fine filter: 1 m 65 m Material: Pure titanium Operating Temperature: 0 300 Thickness: 0.8mm 2.8mm Performance: Acid resistance, alkali resistance, high temperature resistance, breathable Features 1. Corrosion resistance It exists between the bipolar plate and the catalyst layer. During the electrochemical reaction, the high current density is 2A/cm2, which has high electrical corrosion resistance and must have corrosion resistance; 2. Porous air permeability Serve as a medium for hydrogen/oxygen or methanol/air to diffuse to the catalyst layer, and must be a porous and breathable material; 3. High conductivity To act as a current conductor, it must be a highly conductive material; 4. High thermal conductivity The reaction is an exothermic reaction, and overheating will cause damage to the proton exchange membrane. The gas diffusion layer must be a high thermal conductivity material to conduct heat away to avoid damage to the proton exchange membrane; 5. Good permeability Fuel cell reaction to generate water will cause performance degradation, so the gas diffusion layer must be able to export water and have high hydrophobicity; Due to its characteristics, porous titanium plates can also be used in the following industries: (1) Manufacture of sweating material. That is, the pores of ordinary powder metallurgy materials are impregnated with low-melting point substances, and they work at high temperatures At this time, the impregnation melts and seeps out, making the material "sweat" to dissipate heat. In this way, ordinary materials can be used to replace expensive heat-resistant alloys, and the service temperature of heat-resistant parts can be further increased. (2) Manufacture filter material. Used to filter gas, filtrate, and poison, etc. (3) Impregnated with the anti-friction agent to manufacture oil-containing and oil-free lubricated bearings; impregnated with spices to manufacture fragrance-containing handicrafts, etc. (4) Manufacture materials such as vibration reduction, noise reduction, and heat insulation.

Titanium felt, a diffusion layer material, provides electrons between the catalyst layer and the bipolar plate or the current distributor on the anode side. Due to its three-dimensional network porous structure, high porosity, high corrosion resistance and other characteristics, titanium felt has become one of the best materials of diffusion layer in fuel cell and hydrogen production by water electrolysis. Parameters: Material: Titanium Size:1500*1200mm Thickness:0.2mm, 0.25mm, 0.40mm, 0.60mm, 0.80mm, 1.00mm, 2.0mm. Porosity:60% - 75% â?» Porosity and Size can be customized. Technological Process Pure titanium (special process)-titanium fiber (laying, sintering)-titanium fiber felt (with three-dimensional network porous structure)- Titanium felt for LGDL Features: 1. Three-dimensional grid porous structureï¼? 2. Strong corrosion resistanceï¼? 3. Optimal electrolysis performanceï¼? 4. High porosity and current densityï¼? 5. Uniform pore size distribution. Applicantion 1. Liquid/gas diffusion layer; 2. Hydrogen absorber; 3. Hydrogen-rich water dispenser; 4. Diffusion layer of hydrogen cell stack; 5. PEM hydrogen production by water electrolysis.