Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
Metallized microwave ferrite substrate for antenna use
Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1m4mAu2.5m5.7m. The plating thickness should be 8~10m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu36mNi14m Au12m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1 m 4 m Au2.5 m 5.7 m. The plating thickness should be 8~10 m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu3 6 m Ni1 4 m Au1 2 m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Metallized microwave ferrite substrate for antenna use.
Metallized microwave ferrite substrate for antenna use.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
ALTUS Almd-15 Microwave Oven
1>No matter the temperature or weather changes, the fertilizer composition won't burn the root system. 2> Also has good drainage, fertilizer retention and air permeability to provide a high-quality environment for the seedlings during the growth stages. 3> Stimulating the growing of root system, and improving the quality. 4> Using quick-acting fertilizer ingredients that can match the needs of the seeds growing stage. 5> At the same time, adding slow-acting fertilizers which dissolve after touching plant root acid. Ensure that plants can absorb effective fertilizers at all stages of breeding. Content N 120mg/L PO 800-1000mg/L KO 120mg/L
Organic fertilizers (pellet shape compost fertilizer), compound fertilizers with organic matter, fish meal, organic chicken manure, compost fertilizers (cow dung), potting/seedling substrates, horticultural potting substrate, aquatic soil, organic cat litter, mushroom extract bio stimulator, compound fertilizers, etc., cacl2 � calcium chloride 74%.
High street customer returnes sold only in bulk. All our item are ideal for expoters. Mini one pallet. Discount for container buyers Sold by the pallet only or full-load 24 pallets.
Our Wooden Spoons for Cooking are made by natural wood, and well finished without any painting, looks simple but exquisite! To keep your Wooden Spoons for Cooking at their best, with neutral soapy warm water by hands and dry thoroughly after every time use. Wipe with oil for maintaining per month! And avoid abrasives, pro-longed soaking in water and DO NOT put these wooden spoons for cooking into dishwasher, microwave, freezer or oven.