Mcc Panels Suppliers and Manufacturers

It also called MCC panel, we manufacture as per customer drawing or as per customer requirement we use sheet metal with powder coating .For wiring we use standard rating wire . The switch gear used in this as per customer requirement.

This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements

This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements

This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements

The MCC (Motor Control Center) panels are available with multiple power stabs that help in supporting high capacity industrial motors. These have the capacity to feed larger loads and are designed as per the client specifications. Our manufactured MCC units comprises of Full voltage non-reversing and full voltage reversing starters, AC variable frequency drives, PLC I/O chassis, Solid-state motor controllers, Lighting panels, Transformers, Analog or digital metering, Feeder circuit breakers, Feeder fusible disconnects. An intelligent MCC is simply an MCC that maximizes the value of the components in a given application. We have the latest and the best technology to design and build an intelligent MCC Panel to perfectly suit our customer requirement.

Control panel for distribution, apfc, & automation of industries along with metering panels for houses, commercial building and complex. According to their standards. Higher gauge cr sheets are used to fabricate along with 7 dip process powder coated finish.

Access Panel