Through the headed bars of anchor plate to increase the friction between the concrete and steel, improve its ability to resist drawing, in case of steel was pulled out,instead of bent ends. It is approach greatly simplifies rebar placement and reduces congestion.
Rebar range 16-40mm, No limitations on the type, composition, or weldability of steel bars, it's widely used in bridge construction.
Hebei Yida Anti Impact Rebar Coupling system is a mechanical rebar splicing system, be made of high quality alloy steel. It has already passed the High Speed Tensile test of Anti instant impact by Germany Berlin BAM Laboratory. It has been widely applied at the sites where required high level of resistance to impact. The coupler sleeve will be perfect connected with rebar by cold swaged deformation in the application, and dual couplers will be connected by a high strength bolt.
Transition taper thread couplers are designed to splice different diameter bars where one bar can be roated and the bar is not restricted in its axial direction.
Rebar Cold Extrusion Technology The Cold Extrusion Machine is made up by a hydraulic Clampy with Cold Pressing Dies and Hydraulic Oil Pump.� Only 1 â?? 3 kw power of oil pump, which is not limited by power capacity, has flexible structure and suitable for operation on several machines. Advantages: No professional and experienced worker needed, able to connect changed steel bar of different diameters. Save 80% of connector steel consumption. Only needs 1 3m to stamp each connector, which is about ten times faster than ordinary welding. No flammable gases, not affected by rainy or cold weather. Relieve congestion of the connecting point, facilitated concrete pouring.
Casing with a separate power supply unit power supply of hydraulic tools to squeeze on steel. The final connection ensures a tensile strength of at least 125% of the nominal yield strength of the reinforcement grade 500 MPa.
Hebei Yida BGZL-40B3 steel bar straight screw thread processing rib peeling machine is the exclusive use rib peeling knurling machine for the straight screw thread connecting. It is mainly used in the processing/fabrication of the end of the structural steel bar. Positive And Negative Screw Thread Model Used in the occasion when the steel bar in the two sides both can not be turned but the lengths can be adjusted.
This Automatic Upset Forging Machine is the preparative machine for rebar connection in construction work. Its main function is to forging the end part of rebar to raise the rebar area and therefore enlarge the strength of rebar end.
BGZL-40B3 steel bar straight screw thread processing rib peeling machine is the exclusive use rib peeling knurling machine for the straight screw thread connecting. It is mainly used in the processing of the top of the structural steel bar.
Rebar range 16-40mm, No limitations on the type, composition, or weldability of steel bars, it's widely used in bridge construction.
Rebar range 16-40mm, No limitations on the type, composition, or weldability of steel bars, it's widely used in bridge construction.
Upset Parallel Threaded Rebar Coupler 100% bar break through tensile test. Material of the rebar coupler is No.45 steel. High precision thread, full thread type, no false thread.
1. Wide range of application, no weldability requirements for rebar, suitable for �?12 ~ 50mm HRB400, HRB500 same diameter or reducing diameter steel bar connection in any direction; 2. Convenient construction, fast connection speed, and the on-site connection and assembly operations take up a short time; 3. Environmentally friendly construction, no noise and pollution on site, safe and reliable.
Comparison of using laps and rebar coupler: 1. Reduce or eliminate some of the costs of lap splicing by using rebar coupler. 2. The use of laps can be time-consuming in terms of desigh and installation and the increased amount of rebar creats congestion within the concrete The Characteristics of the Usage Standard Model used in the occasion for connecting the steel bar in normal situation Different Diameter Model used for connecting the steel bar in different diameters Flared Model used for the steel bar which was hard to match Positive And Negative Screw Thread Model Used in the occasion when the steel bar in the two sides both can not be turned but the lengths can be adjusted. Locking Nut Model Used when the steel bar can not be turned, then it turns the splicing coupler to join the steel bar and then lock the splicing coupler with the locking nut.
Rebar fabrication equipment, bsts rebar thread cutting machine used for LINXION PI mechanical connection, best selled in India market. The advantages: 1.High efficency by manual operation of thread cutting; 2.Easy operate, no need to change other parts at same thread pitch, applied for 16-40mm all diameter deformed bars. 3.Easy and simple for working man
1.Place it well at the working point. 2.Directly use it to press connection point with screwless couplers to link the two rebar.
YDZTS-40C Rebar Taper Thread Cutting Machine is designed and manufactured by Hebei Yida Reinforcing Bar Connecting Technology Co., Ltd. 1. It is mainly used as a special equipment to make taper thread on the end of the rebar in the processing of rebar connection. 2. The applicable diameter is from �¯�¿� 16 to �¯�¿� 40. It applies to Grade �¢?�¡ and �¢?�¢ level rebar. 3. It has reasonable structure, light and flexible, simple operation, high production efficiency. It is widely used in steel bar end processing of taper thread joints in concrete works. 4. It adapts to a variety of complex construction site environment.
