Heavy Melting Steel (HMS): Heavy melting steel is a designation for recyclable steel. It is categorised into two major categories: HMS 1 and HMS 2. The difference between the two is HMS 1 does not contain galvanized and cast iron, whereas HMS 2 does. Because both grades guarantee a minimum piece thickness â?? at least 1/4inch (6.3mm) for HMS 1, and 1/8 in for HMS 2 â?? consignments have a high density. The typical constituents are plates, truck parts, structural items, large machinery parts, automatic parts, pipes, post consumer steel goods. Quality Heavy metal ,Iron Scrap/ Metal scrap HMS 1 and HMS 2 scrap steel for sale
R50- R65 - IRSI CODES; The chemical composition is the standard for R-50 R-65 Tee rails original weigh 50 pounds per yard or heavier,6 meters long and over. Material to be suitable for rerolling into bars and shapes. Free from bent and twisted rails, frog, switch and guard rails, rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from end of the piece of rail. Free from Fluff, Nonferrous inclusions, excessive rust and other impurities. Free from war and explosives, shells, cartridges, other arms and ammunitions used or otherwise and any closed containers. Free from any radioactive materials, any harmful chemicals, substances, and coatings any organic waste any other harmful substances. Dirt, dust, rust fluff and other impurities not allowed over 05 %. The rails are to be neatly bundled and secured with iron wire or straps, provided with adequate lifting hooks. Individual bundles not to exceed 5 MTW. Used Rails R50 - R65 Chemical Composition Used Rails; C: 0, 54 - 0,82 Si: 0,18-0,40 Mn: 0, 60-1, 05 S: 0.04 max P: 0,035 max As.: 0, 01 max of Mass share Norms: R-50 GOST7173-75 and R-65 GOST-8165-75 The scrap consists of R-50 (51, 67 kg/m) R-65 (64,72 kg/m) Used Rail ISRI 27-29 ISRI-CODES; (27) Rail, Steel No. 1. Standard section tee rails, original weight 50 pounds per yard or heavier, 10 feet long and over. Suitable for re-rolling into bars and shapes. Free from bent and twisted rails, frog, switch, and guard rails, or rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from the end of the piece of rail. (28A) Rail, Steel No. 2 Cropped Rail Ends. Standard section, original weight of 50 pounds per yard and over, 18 inches long and under. (28B) Rail, Steel No. 2 Cropped Rail Ends. Standard section, original weight of 50 pounds per yard and over, 2 feet long and under. (28C) Rail, Steel No. 2 Cropped Rail En ds. Standard sec t ion, original weight 50 pounds per yard and over, 3 feet long and under. (29) Rail, St eel No. 3.Standard section tee, girder, and/or guard rails, to be free from frog and switch rails not cut apart, and contain no manganese, cast, welds, or attachments of any kind except angle bars. Free from concrete, dirty and foreign material of any kind. The rails can be cut to the length the buyer wants
GerardJOSEPH llc is an American company specializing in international supply of Consumers goods. We are a family business that is delivering the highest quality of consumer goods to buyers all over the world. We own shares of companies through the USA that do the production for us. High quality of products are guaranteed thanks to careful, detailed and research. Thanks to the policy followed by the company, we are conceived in the market as a reliable, honest and business like partner, the one that guarantees the highest standard of products. ISRI-CODES: (27) Rail, steel No.1 â?? Standard section T rails, original weight 50 pounds per yard or heavier, 10 feet long and over. Suitable for re-rolling into bars and shapes. Free from bent and twisted rails, frog, switch and guard rails or rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from the end of the piece of rail. (28a) Rail, steel No.2 â?? Cropped Rail Ends, standard section, original weight of 50 pounds per yard and over, 18 inches long and under. (28b) Rail, steel No.2 â?? Cropped Rail Ends, standard section, original weight of 50 pounds per yard and over, 2 feet long and under. (28c) Rail, steel No.2 â?? Cropped Rail Ends, standard section, original weight of 50 pounds per yard and over, 3 feet long and under. (29) Rail, steel No.3 â?? Standard section T, girder and/or guard rails, to be free from frog and switch rails not cut apart and contain no manganese, casts, welds or attachments of any kind except angle bars. Free from concrete, dirt and foreign material of any kind. We are trading in the finest quality Metal Scrap/ Aluminum Scrap, which are recycled for producing pure copper products and equipment.
Good quality Obsolete Pipes is available in large quantity. Called HMS1 available in bulk quantity our MOQ is minimum 1000 mt.
HMS 1 Qty 800 MT
Available New Stock HMS1/2 in bulk - We offer 30,000 MT per shipment with a minimum order quantity (MOQ) of 30,000 MT. Our contract includes 12 shipments per month (+/-5%), with the potential to increase to 150,000 MT per month over a 12-month period. Key Details: Contract: 12 shipments/month Origin: Eastern Europe Delivery Terms: CIF/CFR/CIP
C 0.54 -0.82 Si 0.18 - 0.40 Mn 0.60 - 1.05 S 0.04 max P 0.035 max As 0.01 max of Mass share Norms R-50 GOST-7173-75 and R-65 GOST-8165-75 R50 (51.67 KG/M) GOST 7173-75 R65 (64.72 KG/M) GOST 8165-75 In ferrous we mainly deal in HMS1 & 2 Material Specification Heavy Melting Scrap (HMS 1& 2) ,80% HMS 1 & 20 % HMS 2 confirming to ISRI 200-206 HMS 1 ISRI Code 200: heavy melting steel. Wrought iron and/or Steel scrap inch or steel scrap inch and over in thickness. Individual pieces not over 60 x 24 inches HMS 1 ISRI Code 201: heavy melting steel 3 feet x 18 inches. Wrought iron or steel scrap HMS 1 ISRI Code 202: heavy melting steel 5 feet x 18 inches. Wrought iron or steel scrap HMS 2 ISRI Code 203: heavy melting steel. Wrought iron or Steel scrap, Black and Galvanized. 1/8 inch and over in thickness, charging box size to include material not suitable as no.1 heavy melting steel. HMS 2 ISRI Code 204: same as ISRI 203 but max size 36-18 inches. HMS 2 ISRI Code 205: same as ISRI 204 but free of sheet iron or thin-gauged material. HMS 2 ISRI Code 206: same as ISRI 204, but max size 60 x 18 inches
ISRI 200 (HMS 1): Wrought iron or steel scrap 1 4 inch (6.35 mm) and larger in thickness. All pieces must be smaller than 60 in 24 in (1,524 mm 610 mm) ISRI 201 (HMS 1): Same as ISRI 200 except pieces must be smaller than 36 in 18 in (914 mm 457 mm).
SPECIFICATIONS: the following Percentage Points: Chemical Composition Carbon - 0.54 to 0.82% Phosphorus - 0.035% max Manganese - 0.60 to 1.05% As. - 0,01max of Mass share Silicone - 0.18 to 0.40% Sulphur - 0.035% max Norms - R-50 GOST-7173-75 / R-65 GOST- 8165-75 The scrap consists of R-50 (51,67 KG/m) R-65 (64,72KG/m) Used Rails shall be considered free of alloys when the residual alloying elements do not exceed Cut to 1.5 meter length (standard) 1. Technical terms: USED RAIL R50-R65 2. Specifications and Chemical Composition: Used Rail: R50 (51.67KG/Meter, GOST 7173-55), Used Rail: R65 (64.72KG/Meter, GOST 8161-75). Size & Weight: Length: 12meter ~ 12.5meter Maximum or less according tobuyerâ??s instruction; Expenses on seller Width: 5.5 inches ; Weight: 64.72Kg. No fishplates or steel pieces or bolts are attached to the used rails. All rails are clean and straight. No pitting. Only atmospheric rust No heavy rust. It is mandatory that Rails must be cut into length 1.5 meter(max.) before shipment.
Products: Used Rails R50-R65 and HMS 1/2 Quantity: Large Origin: South Africa (Durban Port) Price: $275 MT/CIF (ASWP) Payment Terms: SBLC mt760 guarantee with 2% PB
SPECIFICATIONS Steel Scrap in bulk according to grade HMS 1&2 Max size 1500*500*500 mm. 40% of HMS 2, sheets of max 4mm thick, max 5% of galvanized steel (close to ISRI 203), max 2% of soil is acceptable. Cast iron, baled scrap, non-ferrous metals, explosive shells of military type, any gas tubes (empty or full), radioactive materials, slag, melt, stones is not allowed. Oversize is not allowed.
We can provide HMS 1 & 2 (80/20) scrap metal from Europe. Payment terms - LC at sight after inspection Minimum quantity - 50 MT Maximum quantity - 200 MT If interested please send us a LOI stating your requirement. Pics will be provided. Only serious buyers please contact.
HMS 1&2 is produced from various sources and clean and clear material Product origin : Multiple Origin Key Specifications/Special Features : HMS 1&2 scrap is available as per buyers requirement with multiple options. supply available to any part of the world. Material is free from rediation and clean, clear and acceptable anywhere. Minimum Order Size and Packgaing details MOQ: 25 Ton Packaging: Bulk
We are specialized in the sales of full metal scrap such as ac/fridge compressor , H.M.S 1&2,Aluminum Ingots and UBC Scraps Copper wire scrap, Drained Battery Lead scrap in the UK (LONDON).We have all our product fully ready for sales in good quantity and quality also to be shipped out for our buyers.Create a long time business relation with us & save a lot more.
Application : Melting, Re Rolling Source : Old Machine Parts Etc Polished : No C Content : 0.06 - 0.082% Pack Size : 5-50 kg Fe Content : 98% Grade : HMS 1 & 2 Pack Size : 100-500 Kg
1 IRON & STEEL SCRAP SPECIFICATIONS Specifications Type of Scrap: # 1 HMS ISRI Code: 200/201/202 ISRI name: No. 1 heavy melting steel Gerdau name: # 1 Heavy Melt Wrought iron and/or steel scrap 1/4 inch and over in thickness. Individual pieces prepared in a manner to insure compact charging. Minimum density 55 lbs. per cu. ft. Expected Chemistry (%; max) Dimension (inches; max) Copper 0.300 Chrome 0.150 Nickel 0.150 Tin 0.015 Phosphorous 0.040 Sulphur 0.040 Silicon 0.25 Molybdenum 0.030 Cartersville 48 x 24 x 4 Jackson 12 x 12 x 24 Manitoba 48 x 24 x 4 Monroe 12 x 12 x 24 St. Paul 60 x 18 x 4 Whitby 48 x 24 x 4 Wilton 60 x 18 x
Heavy Metal Steel (HMS 1&2)
Commodity: Quality Grade HMS Origin : USA CHEMICAL COMPOSITION: C: 0, 54 - 0, 82%; SI: 0, 18 - 0, 40%; MN: 0, 60 - 1, 05%; S: 0, 04% MAX; P: 0,035% MAX; AS: 0, 01% Max of mass HMS 1 ISRI Code 200: heavy melting steel.Wrought iron and/or Steel scrap inch or steel scrap inch and over in thickness.Individual pieces not over 60 x 24 inches HMS 1 ISRI Code 201: heavy melting steel 3 feet x 18 inches. Wrought iron or steel scrap HMS 1 ISRI Code 202: heavy melting steel 5 feet x 18 inches. Wrought iron or steel scrap HMS 2 ISRI Code 203: heavy melting steel. Wrought iron or Steel scrap, Black and Galvanized. 1/8 inch and over in thickness, charging box size to include material not suitable as no.1 heavy melting steel. HMS 2 ISRI Code 204: same as ISRI 203 but max size 36 - 18 inches. HMS 2 ISRI Code 205: same as ISRI 204 but free of sheet iron or thin-gauged material.HMS 2 ISRI Code 206: same as ISRI 204, but max size 60 x 18 inches Hms 1 Hms 2 Metal Scrap/used Rails/cast Iron Free from mud, dust, fluff, non ferrous inclusions, excessive rust and other impurities. Free from war and explosives, shells, cartridges,other arms and ammunition used or otherwise and any closed containers. Free from any radioactive materials, any harmful chemicals, substances, and coatings, any organic waste and any other harmful substances. Dirt, dust rust, fluff and other impurities not allowed over 1%.
HMS 1 and 2 Scrap
We can offer to competitive prices,rationality procedures and basic conditions for used rail ans HMS 1/2. -Goods: Used rail R 50~65 and HMS 1/2 (80/20%) -MOQ : 30,000 x 12 months (no spot & trial order) -Origin: Russia -Payment: By irrevocable, Non- transferable, Documentary L/C payable and within five (5) days after inspection at the discharge port. -No upfront pay: any fees or any charge by seller bears all cost. -P/bond :seller's bank issues PBG 2% to buyer's bank. We only want serious buyers and their mandate and we don't work to long chain agent or broker. If you interested, direct send us via our e-mail address for your orders of full details. I waiting your good answer.
