High Pressure Relief Valve Suppliers and Manufacturers

Description: To ensure safety, the drilling pump is equipped with safety valve in the outlet, which is able to control the ultimate pressure of the pump within the admitted scope. The high pressure safety valve is forged by high quality structural alloy steel. As a kind of protection device and human safety device, it is generally installed on cementing devices, fracturing pump, high pressure operation piping, pressure vessel and devices under high pressure and high flow capacity. It controls elastic force of the valve seat by adjusting the nut on the top. Once the pumping pressure or piping pressure exceeds pre-established pressure value, safety valve opens automatically to release the pressure. When the pressure value reaches the normal value, valve rod will recover the position by spring and close the valve.

To ensure safety, the drilling pump is equipped with safety valve in the outlet, which is able to control the ultimate pressure of the pump within the admitted scope. The high pressure safety valve is forged by high quality structural alloy steel. As a kind of protection device and human safety device, it is generally installed on cementing devices, fracturing pump, high pressure operation piping, pressure vessel and devices under high pressure and high flow capacity. It controls elastic force of the valve seat by adjusting the nut on the top. Once the pumping pressure or piping pressure exceeds pre-established pressure value, safety valve opens automatically to release the pressure. When the pressure value reaches the normal value, valve rod will recover the position by spring and close the valve.

AAK hydraulic relief valve is resistant to high pressure and is not stuck. Ernst doesn't want to change the supplier any more Ernst is from a German hydraulic equipment company. He has been doing well in recent years, and his boss is optimistic about him. The hydraulic relief valves purchased this time has suffered a big setback. In the second half of last year, the hydraulic power unit sold by their company for less than 3 months was complained by customers. When the pressure of the hydraulic relief valve was adjusted to 450bar, the equipment idled. The engineer thought that it could be solved by changing the motor. As a result, after the equipment started for a while, the same situation happened again. The engineer checked each component, and it turned out that the spool of the hydraulic relief valve was stuck. After the boss knew about it, he asked Ernst to request the original hydraulic relief valve manufacturer to solve the problem and bear the motor cost twice. Per the manufacturer, the price of the hydraulic relief valve is too low this time. Under the high pressure of 450bar, it is difficult to avoid a few stuck occasionally, then there is no further news. Ernst had no choice but to find new hydraulic relief valve suppliers. Ernst contacted more than 10 factories and requested that the hydraulic relief valve be 100% free of jamming within 1 year under the high pressure of 450bar. Only two factories were willing to cooperate with the samples, and other manufacturers gave up directly. Ernst still seemed worried about wasting time. With the introduction of his friend Steven, who is our old customer, he contacted AAK hydraulic valve. Ernst asked us to make samples directly according to his hydraulic relief valve drawings and working conditions. The key of this hydraulic relief valve is how long the service life of the hydraulic relief valve is under 450bar high pressure? Actually, AAK has already mass produced hydraulic valves with similar requirements. Nine months later, Ernst informed by e-mail that the hydraulic relief valve from one factory had been on strike because of its stuck, and the other factory's, although still working, it was estimated to be less than 12 months. After 9 months of use, the parameters of AAK hydraulic relief valves are still stable and function normally. Ernst said that compared with more than 10 factories, AAK high-pressure hydraulic relief valve has the most stable performance and longest service life among all the manufacturers he knows. Ernst estimated that he would not need to change the hydraulic relief valve suppliers any more. AAK hydraulic relief valve has 3 advantages and has already surpassed its domestic counterparts. 1. AAK has a high-precision CNC machining center imported from Switzerland and its own upgraded and refitted independent fixture, which eliminates human errors. The high-precision control of component processing is the key point to prevent jamming.

AAK hydraulic relief valve is resistant to high pressure and is not stuck. Ernst doesn't want to change the supplier any more Ernst is from a German hydraulic equipment company. He has been doing well in recent years, and his boss is optimistic about him. The hydraulic relief valves purchased this time has suffered a big setback. In the second half of last year, the hydraulic power unit sold by their company for less than 3 months was complained by customers. When the pressure of the hydraulic relief valve was adjusted to 450bar, the equipment idled. The engineer thought that it could be solved by changing the motor. As a result, after the equipment started for a while, the same situation happened again. The engineer checked each component, and it turned out that the spool of the hydraulic relief valve was stuck. After the boss knew about it, he asked Ernst to request the original hydraulic relief valve manufacturer to solve the problem and bear the motor cost twice. Per the manufacturer, the price of the hydraulic relief valve is too low this time. Under the high pressure of 450bar, it is difficult to avoid a few stuck occasionally, then there is no further news. Ernst had no choice but to find new hydraulic relief valve suppliers. Ernst contacted more than 10 factories and requested that the hydraulic relief valve be 100% free of jamming within 1 year under the high pressure of 450bar. Only two factories were willing to cooperate with the samples, and other manufacturers gave up directly. Ernst still seemed worried about wasting time. With the introduction of his friend Steven, who is our old customer, he contacted AAK hydraulic valve. Ernst asked us to make samples directly according to his hydraulic relief valve drawings and working conditions. The key of this hydraulic relief valve is how long the service life of the hydraulic relief valve is under 450bar high pressure? Actually, AAK has already mass produced hydraulic valves with similar requirements. Nine months later, Ernst informed by e-mail that the hydraulic relief valve from one factory had been on strike because of its stuck, and the other factory's, although still working, it was estimated to be less than 12 months. After 9 months of use, the parameters of AAK hydraulic relief valves are still stable and function normally. Ernst said that compared with more than 10 factories, AAK high-pressure hydraulic relief valve has the most stable performance and longest service life among all the manufacturers he knows. Ernst estimated that he would not need to change the hydraulic relief valve suppliers any more. AAK hydraulic relief valve has 3 advantages and has already surpassed its domestic counterparts. 1. AAK has a high-precision CNC machining center imported from Switzerland and its own upgraded and refitted independent fixture, which eliminates human errors. The high-precision control of component processing is the key point to prevent jamming.

High pressure reduce relief safety valve.

Our old Greek customer, Evander, emailed me in November last year that he sent me a sample of hydraulic cartridge relief valve, and stressing that it was not his, but one of his partners, Ptolemy, and also attached Ptolemy's contact information. After receiving the sample and communicating with Ptolemy, we learned that the hydraulic cartridge relief valve was produced by a local cartridge valve manufacturer in Greek and installed in their hydraulic cylinder, which was unstable. Their engineers said that the root cause was the high back pressure of the hydraulic system and the insensitive opening of the hydraulic cartridge valve. We can't determine the hidden dangers of the hydraulic cartridge valve just according to the original sample. I suggested Evander sending us the video of abnormal hydraulic cylinder, the drawing of hydraulic cartridge valve, and the schematic of the system. After discussing, AAK engineers advised that the problem can only be solved by reducing the opening back pressure resistance of the hydraulic cartridge valve. Perhaps because of Evander's endorsement, Ptolemy paid the development fee on the second day. I have always believed that for industrial products such as hydraulic cartridge valves, it is difficult to get the order without trust. With trust and reliable manufacturing quality, it is easy to get the order. After 40 days, AAK sent 20 samples of hydraulic cartridge valve. Yesterday, Ptolemy emailed me that AAK hydraulic cartridge relief valve was used on the hydraulic cylinder. The prototype operated stably and the hydraulic cartridge valve opened sensitively. AAK hydraulic cartridge valve is stable and sensitive under high back pressure. We optimized the structure of the original hydraulic cartridge relief valve from 3 aspects. 1. The valve sleeve of the hydraulic cartridge relief valve has an oil inlet cavity, and the outer circle of the valve sleeve is provided with a plurality of annular through holes as oil outlet, and oblique holes are set to control the oil outlet. 2. The middle part of the main valve spool is provided with a small hole connecting the oil inlet cavity and the inclined hole, and the main valve spool can slide in the valve body to form a spring cavity that is relatively closed to the oil inlet cavity, and the spring cavity is equipped with a pressure regulating spring. 3. The left end of the valve body is installed with an adjustable rod that can be rotated and retracted and has a lock nut. The pressure regulating spring on the adjusting rod is connected to the main valve spool. The outer diameter of the right end of the valve body is provided with a sealing groove to place the sealing ring group. Two sealing grooves are set on the left side of the external thread of the valve body, and the sealing ring group is placed to seal the connection with the socket to prevent oil leakage. The optimized AAK hydraulic cartridge relief valve equalizes the pressure difference