Find Verified Heat Seal Tester Suppliers, Manufacturers and Wholesalers

Application and Brief Intro HST-01 Heat Seal Tester is for the determination of the heatsealability of a surface, or sealant layer of films, laminates, composites and polymers etc. How well the material heatseals is expressed quantitatively as seal strength as a function of the sealing conditions of temperature, time and pressure. HST-01 Heat Seal Tester is professionally designed for the precise measurement of the three parameters of temperature, time and pressure in the heat seal process. HST-01 Heatsealability Tester conforms to standards of ASTM F2029, QB/T 2358 and YBB 00122003. Principle Place a sample between two-heated sealing jaws of HST-01 Heat Seal Tester with flat surfaces when the required temperature reaches equilibrium. The upper seal jaw, driven by a gas cylinder, is pushed down, to exert a certain pressure on the sample and remain for some time. When the preset sealing time ends, the upper sealing jaw returns to its original position and the whole heatsealability testing process finishes. ASTM F2029, QB/T 2358, YBB 00122003

The instrument adopts the specially designed heat sealing jaws, which completely conform to multiple national and international standards. 1. Digital P.I.D. temperature control technology ensures the preset temperature to be reached rapidly without any fluctuation 2. Wide range control of temperature, pressure and time that meet various test conditions 3. Manual or pedal switch, as well as anti-scald design provides convenient and safe operating environment 4. The instrument is controlled by micro-computer with LCD, PVC operation panel and menu interface. Basic Applications: Films with Smooth Surface Films with Decorative Pattern Surface Extended Applications: Covers of Jelly Cups Flexible plastic tubes.

Instrument structure: The structure of the heat-sealing tester is composed of 4 parts: pneumatic drive system, heat-sealing equipment, temperature adjustment system and time adjustment system. Pneumatic drive system: It includes pressure gauge, guide stick, cylinder, pneumatic valve, pressure regulating handle and so on. You can pull the pressure-regulating handle outward, rotate to the right side to adjust the heat sealing pressure to a high value, and rotate to the left side to reduce it. After setting the pressure, please press the handle to the side of mainframe to lock the air pressure. Heating-seal device It is composed of the upper and lower heat-sealing sticks, of which the upper one is connected with a cylinder. There is an insulating plate in the upper part, which can prevent heat transmit to the cylinder. The heat-sealing stick is made of aluminum, and the center is heater. There is a silica gel plate in the upper part of the lower heat-sealing stick, which can mitigate pressure impact during heat sealing. Temperature measurement system was installed at the back of the heat-sealing stick. Temperature adjustment system: The upper temperature controller controls the temperature of upper heat-sealing stick, and the rear temperature controller controls the temperature of lower heat-sealing stick. The temperature can be set at will through adjusting the button on the dial plate. Time adjustment system: Time adjustment system: The heat-sealing time can be set at will through adjusting the button on dial plate. The setting scope of time is 0.01s to 999.9h. Press the foot switch under the manual state, and the heat-sealing stick will be pressed together. Under the automatic state, the press-fitting time of upper and lower heat sealing sticks are controlled by a timer automatically, it can automatically recover later. The unit of timer is 0.1 second in general. There is time adjusting button on the panel of the timer, and the heat-sealing time can be adjusted at will. Specifications Power : AC220V  50HZ  ; Compressed Air : 8kg/cm2; Heat sealing plane : 300mm×10mm slick (With silicon pad in lower seal stick); Heat sealing temperature : room temperature 20~300°C (Precision 1°C); Heat sealing time : 0.01s~99.99h; Heat-sealing pressure : 0~0.8Mp. Dimension: 700 (L) mm×400 (W) mm×540 (H) mm Weight: Desktop 30Kg.

Heat Seal Tester is professionally applicable to the determination of heat-sealing temperature, dwelling time and the heat-sealing pressure which are references to the production of aseptic bag, food, pharmaceutical, daily chemicals, package and raw material. Features Micro-computer control tests. Touch interface is easier to operate. Self-innovated "constant temperature control" system improves the accuracy of temperature. The synchronous circuit of single bottom cylinder ensures the balance of pressure. Aluminum-sealing jaws provide even and uniform temperature for different sealing surfaces The upper and lower jaws controlling the temperature independently and the super-long thermal cover can meet different needs. Dual switch modes of manual and foot make the safety and convenience. Micro-printer embedded can get the results quickly. The design of anti-scald and leakage protection is more secure to test. Principle HST-H3 Heat-Seal Tester is composed of upper and lower heat sealing jaws. Before the test, preset the values of heat-sealing temperature, pressure and dwelling time, then place the specimen in between the upper and lower jaws and press start button. The whole sealing process can be finished automatically. Standards QB/T 2358, ASTM F2029, YBB 00122003. Applications Films with Smooth Surface Films with Decorative Pattern Surface Covers of Jelly Cups Plastic Flexible Tubes Technical Specifications Heat-Sealing Temperature Room temperature ~ 300 Accuracy of Temperature Control 0.2 Sealing Time 0.1999.9s Sealing Pressure 0.05MP-0.7MPa Sealing Area 330mm10mm (Customization is available) Heating Form Double heating (Optional: single heating) Air Pressure 0.05 MPa ~ 0.7MPa Air Connection 6mm PU tube Dimension 536 mm (L)335 mm (B)413 mm (H) Net Weight 40 kg

Heat Seal Tester is applied in measuring heat sealability of a surface, or sealant layer of films, laminates, composites and polymers etc. How well the material heat seals is expressed quantitatively as seal strength as a function of the sealing conditions of temperature, time and pressure. Standard: ASTM F2029

HST-H3 Heat Seal Tester (Laboratory Heat Sealer) can be used to seal specimen for further determination of seal parameters of basic films, laminated films, coating paper and other heat sealing laminated films according to the requirement of related standards.

Hst-h6 heat seal tester can be used to seal specimen for further determination of seal parameters of basic films, laminated films, coating paper and other heat sealing laminated films according to the requirement of related standards.

Classic 513 gradient heat seal tester is professionally designed for the determination of heat-sealability of plastic films, composite films, coated paper, and other sealing films under certain sealing speed, pressure and 5 different temperatures.

Function and usage It can set with 5 different temperature spots to do heat sealing, select the optimal heat healing temperature, and can also set the same temperature to speed up the heat sealing. Instrument structure: The structure of the heat-sealing tester is composed of 4 parts: pneumatic drive system, heat-sealing equipment, temperature adjustment system and time adjustment system. Pneumatic drive system: It includes pressure gauge, guide stick, cylinder, pneumatic valve, pressure regulating handle and so on. You can pull the pressure-regulating handle outward, rotate to the right side to adjust the heat sealing pressure to a high value, and rotate to the left side to reduce it. After setting the pressure, please press the handle to the side of mainframe to lock the air pressure. Heating-seal device It is composed of the upper and lower heat-sealing sticks, of which the upper one is connected with a cylinder. There is an insulating plate in the upper part, which can prevent heat transmit to the cylinder. The heat-sealing stick is made of aluminum, and the center is heater. There is a silica gel plate in the upper part of the lower heat-sealing stick, which can mitigate pressure impact during heat sealing. Temperature measurement system was installed at the back of the heat-sealing stick. Temperature adjustment system: The upper temperature controller controls the temperature of upper heat-sealing stick, and the rear temperature controller controls the temperature of lower heat-sealing stick. The temperature can be set at will through adjusting the button on the dial plate. Time adjustment system: Time adjustment system: The heat-sealing time can be set at will through adjusting the button on dial plate. The setting scope of time is 0.01s to 999.9h. Press the foot switch under the manual state, and the heat-sealing stick will be pressed together. Under the automatic state, the press-fitting time of upper and lower heat sealing sticks are controlled by a timer automatically, it can automatically recover later. The unit of timer is 0.1 second in general. There is time adjusting button on the panel of the timer, and the heat-sealing time can be adjusted at will. Specifications Power : AC220V 50HZ Compressed air: 8kg/cm2 Heat sealing plane: 300mm10mm slick (With silicon pad in lower seal stick) Heat sealing temperature: room temperature 20~300C (Precision 1C) Heat sealing time: 0.01s~99.99h Heat-sealing pressure: 0~0.8Mp. Dimension: 700(L)mm400(W)mm540(H)mm Weight: Desktop 30Kg. 700mm(L)X400mm(B)X540mm(H)

Psst-100 heat seal strength tester is a professional heat seal strength tester for plastic films, composite films and other materials. This instrument is suitable for on-site quantitative inspection.

i-Thermotek 2400 Heat Seal & Hot Tack Tester can be used for seal strength test after the seal immediately (hot tack) or waiting it cools to room temperature (heat seal). It can be used for plastic films, composite films, and other packaging materials.

Application Applies to best parameters determination of heat sealability of various kinds of film. Heat sealability of film depends on temperature, pressure and heat time and the HSL-6001 Heat Seal Tester is widely used in food and pharmaceutical packaging industries. Features 1: Our own patent technology 2: Embedded system control 3: Touch screen operation, easy to operate 4: TFT LCD display, UI flattening design 5: Dual heat jaws, temperature controlled independently 6: Micro-printer prints mini-report 7: Pressure easy to adjust, heat temperature and time touch screen input. 8: Emergency stop button, safety design to prevent burns 9: Over temperature protection, over pressure protection 10: Silence working 11: DB9 RS232 communication port. 12: DSM system is optional(Laboratory Management Information System), easy to manage and share test data. Technical Indexes Heat temperature: Room temperature+6 ~ 300â?? Accuracy: ±0.2 â?? Dell time: 0.1~ 999.9s Pressure: 0.05 MPa~1.1MPa Heat jaw surface: 265mm Ã? 12 mm (customized) Heat jaws: 2, controlled independently Gas source pressure: 0.05MPa ~ 1.1MPa (self-provide) Gas source interface: Ф6mm Outer dimension: 536 mm (L)Ã?335 mm (W)Ã?413 mm (H) Work noise: 0db Power supply: AC 220V 50Hz Net weight: 33kg Standards QB/T 2358(ZBY 28004)ã?�ASTM F2029ã?�YBB 00122003 Configuration Delivery: main unit, micro-printer, footswitch, sample feeding rod. Optional: Communication cable, DSM system -

Application Applies to best parameters determination of heat sealability of various kinds of film. Heat sealability of film depends on temperature, pressure and heat time and the HSL-6001 Heat Seal Tester is widely used in food and pharmaceutical packaging industries. Features 1: Our own patent technology 2: Embedded system control 3: Touch screen operation, easy to operate 4: TFT LCD display, UI flattening design 5: Dual heat jaws, temperature controlled independently 6: Micro-printer prints mini-report 7: Pressure easy to adjust, heat temperature and time touch screen input. 8: Emergency stop button, safety design to prevent burns 9: Over temperature protection, over pressure protection 10: Silence working 11: DB9 RS232 communication port. 12: DSM system is optional(Laboratory Management Information System), easy to manage and share test data. Technical Indexes Heat temperature: Room temperature+6 ~ 300â?? Accuracy: ±0.2 â?? Dell time: 0.1~ 999.9s Pressure: 0.05 MPa~1.1MPa Heat jaw surface: 265mm ? 12 mm (customized) Heat jaws: 2, controlled independently Gas source pressure: 0.05MPa ~ 1.1MPa (self-provide) Gas source interface: Ф6mm Outer dimension: 536 mm (L)?335 mm (W)?413 mm (H) Work noise: 0db Power supply: AC 220V 50Hz Net weight: 33kg Standards QB/T 2358(ZBY 28004)?�ASTM F2029?�YBB 00122003 Configuration Delivery: main unit, micro-printer, footswitch, sample feeding rod. Optional: Communication cable, DSM system -

Ft-f1 fogging tester Characteristics: Determines auto's fogging characteristics precisely, guarantees automobiles driving safely. Be applicable for the laboratory and works in low noise. Data test and analysis with professional software, convenient and prompt. Bath temperature controlled by thermostat can be kept constant to 0.1ªc, creating precise testing conditions. Designs friendly and integrally, operates safely and conveniently. World-famous brand elements with stable and reliable performance. The strictly controlled constant thermostat can be used for the other experiments. Conforms to din 75201, iso 6452, sae j1756.

Cosmetics bottle, cosmetics jar, makeup, essential oil, lipstick care bottle, lip gloss bottle, compact case, loose powder pot, spatulas, dosage, mascara bottle, perfume bottle, eyeliner bottle.Provides expert product design / manufacture negotiation / production schedule/ quality control / logistics and shipping.

Glassware, glass tableware, kitchenware, press glass cup, blowing glass cup, glass mug, astray, glass jar, storage bottles, colour glass, bottles, goblet, miscellaneous and bowl, borosilicate.Clearing agent, transportation, shipping.

Film Shrinkage Test Equipment Film Shrinkage Tester GBK-D1 Film Shrinkage test, known as linear thermal shrink test or free shrink test, is used for analyzing the effect of temperature on heat shrinkable films made from polyethylene, ethylene copolymers and their mixtures. Basically, shrinking force, contracting force and shrinking ratio can be measured in such determination. GBPI Film Shrinkage tester conforms to the multiple national and international standards: ASTM D2732 - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting ISO 14616 - Plastics Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures Determination of shrinkage stress and contraction stress DIN 53369 - Testing of plastic films determination of the shrinking stress Film Shrinkage Test Equipment GBK-D1 is used to determination of the degree of unrestrained linear thermal shrinkage and dimensional stability at different temperatures. Widely used in industries of plastic material, plastic products, petroleum, chemicals, research institute, inspection agency and so on. Principle This tester uses the principle of air heating to connect the tested sample to the tension sensor and displacement sensor. After reaching the maximum shrinkage force, it is placed in an external test environment with an ambient temperature of 23 to cool down. The reference temperature, shrinkage force and displacement are recorded, and the recorded data can be used to determine the optimal shrinkage conditions of the film. Standards ISO 14616, ASTM D2732, DIN 53369