Four Core Abc Tension Clamp Suppliers and Manufacturers

Type Suitable Conductor Dia(mm)Description NXJ4-1A,1C 46~50 Trolley type,aluminum alloy body NXJ4-2A,2C 470~120 NXJ4-1B 425~50 Pull plate,the body is weather-resistant NXJ4-2B 470~120 engineering plastics NXJ4-3B 450~185

Application This clamp is for the termination of 2 or 4 cores with hook fixing. Its function is to fix and tighten the insulation conductors. Usage These clamps are designed for anchoring self-supporting LV-ABC lines from 2 to 4 cores. And they also have strong strength which keep the clamp in an open position during the installation of conductors 1) Tool free installation. 2) Made of high mechanical aluminum alloy and anti-UV material. 3) Used for the low voltage LV ABC lines. 4) Available cable size ranges from 3 to 6 mm. 5) All parts are resistant to any environmental effects. 6) Guarantee no cable insulation damages or slipping. 7) Can be delivered with 2 or 4 conductors. Our service 1, Fast Response Time 2, Quality and Certified Products3, Resonable Price 4, Cheap and Reliable Transportation 5, 7*24 Hours After Sales Service

ADSS with The DN Short-span Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The ADSS tension clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters. Easy installation and maintenance. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods

Description ADSS preformed tension clamp is designed for connecting and fastening the ADSS fiber to the overhead pole. Feature 1) quick and easy installation 2) distribute the stress uniformity 3) guarantee no cable damage or slipping 4) strong resistance to corrosion and cruel environment 5) made of aluminum alloy, aluminum clad steel and galvanized steel Order Tips 1- confirm the cable type 2- confirm the cable diameter 3- confirm the span and the rated tensile strength 4- the material can be aluminum alloy, aluminum clad steel or galvanized steel Our service 1, Fast Response Time 2, Quality and Certified Products3, Resonable Price 4, Cheap and Reliable Transportation 5, 7*24 Hours After Sales Service

ADSS Preformed Short Span Tension Clamp Preformed Tension Clamp are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Structure and Materials Shackle - Constructed from hot-dip galvanized steel, the shackle is linked to the reinforcing bar unit. Twisted Chain Ring - Made of hot-dip galvanized steel, the twisted links serve to connect the shackle to the thimble. Sleeve - Composed of hot-dip galvanized cast steel, the sleeve is inserted into the unclamp of the tension clamp to ensure protection and facilitate connection. Armored Rod - Fabricated from aluminum-clad steel wire, armored rods enhance friction through a layer of granular emery within the cable. These rods are pre-assembled into four subsets to reduce misalignment errors and expedite installation. The ends are bent outward to provide strain relief in critical areas where the cable departs. Prefabricated Dead Ends - These components are constructed from either hot-dip galvanized steel wire or aluminum-clad steel wire and are assembled in the shop into a subset featuring a solid layer of emery. This design increases the grip of the tensioning clamps while minimizing lateral pressure.

OEM ADSS Tension Clamp Pre-twisted tension clamps are also known as pre-twisted dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. Pre-twisted dead end is a tension clamp that plays an important role in ADSS/OPGW transmission lines. Dead-end fiber optic cable clamps are used to connect ADSS/OPGW/OPPC to overhead towers or poles. The unique design of the pre-fabricated tension clamps not only simplifies installation, but also ensures a secure cable connection. Dead-end cable clamps provide superior performance in protecting ADSS/OPGW/OPPC cables from stress point damage and preventing signal degradation during transmission. Pre-twisted tension clamps and pulling dead-end cable clamps used on conductors and ground wires are similar in appearance, but the specifications, raw materials, and strength requirements of the two types of pulling dead-end cable clamps are quite different. Although there are different design standards in different countries, we can make OEM according to customers' requirements.

Custom ADSS Tension Clamp ADSS Tension Clamps are used to connect ADSS cables to poles/towers. Armored rods provide protection and cushioning for the ADSS cables. The special design of the prefabricated rods ensures that the tension clamps do not overstress the ADSS cables, thus ensuring a normal service life of the cable system.The ADSS tension clamps are made of aluminium-clad or galvanized steel wire. Structure and raw materials Unshackle - hot-dip galvanized steel. The shackle is connected to the reinforcing bar unit. Twisted chain ring - hot dipped galvanized steel. Twisted links are used to connect the shackle to the thimble. Sleeve - hot dip galvanized cast steel. The sleeve is inserted into the unclamp of the tension clamp to provide protection and connection. Armored rod ----- Aluminum clad steel wire. Armored rods increase friction through a layer of granular emery inside the cable. The rods are shop assembled into four subsets to minimize misalignment errors and speed installation. The ends are bent outward to provide strain relief in critical cable departure areas. Prefabricated Dead Ends - Prefabricated dead ends are made from hot-dip galvanized steel wire or aluminum-clad steel wire and are assembled in the shop into a subset with a solid layer of emery to increase the grip of the tensioning clamps while reducing lateral pressure. Direction 1. Used for connecting connecting poles (towers) to terminal poles (towers), tension poles, or poles (towers) with line clamping angles of 25�° or more. Special specifications: 1 unit for each terminal pole (tower), 2 units for each tension pole (tower), and 2 units for each connecting pole (tower). You can select the specification model corresponding to the appropriate cable diameter range, maximum allowable tension (MAT) or span length from the data sheet.

OPGW the Preformed Helical Tension Clamp The OPGW Premored/Helical Tension Clamp is primarily used to install cables with RTS less than 160 kN to tension towers/poles, corner towers/poles and terminal towers/poles. A complete set of OPGW prefabricated/spiral tensioners includes aluminum alloy or aluminum clad steel dead ends, structural reinforcement rods, support fittings and grounding clamps, etc. Wire Tension Clamp An OPGW (Optical Ground Wire) wire tension clamp is a specialized device used in the installation and maintenance of OPGW cables. OPGW cables are composite overhead cables that combine optical fibers for communication purposes with a metallic ground wire for power transmission and grounding. The OPGW wire tension clamp serves the purpose of securely attaching the OPGW cable to the supporting structure, such as poles or towers, while maintaining the necessary tension. It plays a crucial role in ensuring the stability and reliable performance of the OPGW system.

OPGW Preformed Double Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. Preformed Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. The unique pre-formed tension clamp design not only simplifies installation, but also ensures a secure cable connection. Dead-end cable clamps provide superior performance to protect ADSS/OPGW/OPPC cables from stress point damage and prevent signal degradation during transmission. Pre-formed tension clamps for conductors and grounds are similar in appearance to pulling dead-end clamps, but the specifications, raw materials and strength requirements of the two types of pulling clamps do differ significantly. Although there are different design standards in different countries, we can OEM to customer requirements. As an experienced manufacturer and supplier of preformed tension clamps, Seinei understands the standards, the manufacturing process and understands your needs. If you have any questions, please feel free to contact us.

Tension Clamp for Earth Wire Tension Clamp For Earth Wires are for use by trained craftsmen only. Dead-end clamps should not be used by anyone unfamiliar or untrained in their use. Wire Tension Clamp Tension clamps are designed to non-rigidly secure installation cables to brackets, fasteners on buildings, or utility poles. Cable clamps are installed at the beginning and end of cable runs, suspensions, branches and turns. Tension clamps can also be used where cables sag on large straight sections or form under the influence of increased tensile loads. The design of the products is simple. One of the most popular consists of a cone, a pair of plastic toothed wedges that act as clamping devices, and a steel ring. The principle of operation is simple and consists of self-tensioning the cable using the movable wedges of the clamp. The sale of tension clamps and their use significantly reduces the time and physical costs of installation work. This cable attachment element offers the following advantages There is no need to strip the insulation to expose the mating cable during use; Simple installation, reducing the possibility of errors; No special training of installers is required; No special tools are required to prepare cables for installation; Reduced risk of cable damage and compromised integrity.

ADSS Preformed Short Span Tension Clamp Tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. China ADSS Tension Clamp ADSS tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Features: 1. Component: preformed wire, rubber inserting, casting aluminum shell, right angle shackle, U shackle etc. 2. Usage: supporting,make ADSS cable hang on the pole and tower. 3. Features: a, stress on average, no concentration stress, protect cable better and increase the stiffness of cable in the mount point. b, good dynamic stress. It can provide enough grip strength(10%RTS) c, rubber inserting make abrasion low. d. excellent aluminum alloy improve the mechanical and resist-corrosion function, extend life. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods..

An OPGW (Optical Ground Wire) tension clamp is a specialized device used in the installation and maintenance of OPGW cables. OPGW cables are composite overhead cables that combine optical fibers for communication purposes with a metallic ground wire for power transmission and grounding. The OPGW tension clamp serves the purpose of securely attaching the OPGW cable to the supporting structure, such as poles or towers, while maintaining the necessary tension. It plays a crucial role in ensuring the stability and reliable performance of the OPGW system. Here are some functions of an OPGW tension clamp: Cable Gripping: The tension clamp is designed to securely grip the OPGW cable to prevent it from slipping or becoming loose. It typically consists of specially designed jaws or grips that firmly hold the cable in place. Tension Adjustment: The clamp allows for adjustment of the tension applied to the OPGW cable. This feature is important to maintain the desired tension level in the cable, which is essential for its proper functioning and mechanical stability. Mechanical Strength: OPGW tension clamps are constructed using robust and durable materials, such as stainless steel or aluminum alloy, to provide high mechanical strength. This ensures that the clamp can withstand the tension forces exerted on the cable and withstand environmental conditions, such as wind and ice loading. Electrical Continuity: The tension clamp also maintains the electrical continuity of the metallic ground wire within the OPGW cable. It provides a reliable connection between the cable and the supporting structure, ensuring effective grounding and electrical performance. Corrosion Resistance: OPGW tension clamps are often designed with corrosion-resistant coatings or materials to withstand exposure to harsh outdoor environments, including moisture, UV radiation, and temperature variations.

Qucik detail Place of Origin Zhejiang, China Brand Name CROP Model Number Suspension clamp Product name ABC suspension clamps for self supported Sample Supply Free Material Plastic Installation Quick Certifications ISO9001 OEM Acceptable Export All over the world Business Type Manufacturer

Overview Anchor clamp (anchor, wedge) Crossover is designed for fastening of ADSS fiber optic aerial cable for spans less than 100m. Feature 1.easy and quick installation ,no special tools required. 2.high strength and UV resistant material 3.loop is removable for easy connection with ring fastening. 4.couch on a loop protect the steel rope from chafing at the point of attachment. 5.installation on any pole hardware fitting: brackets, cross-arms or eye bolt with a min eye of diameter 15mm 6.locking projections in wedge provides sufficient contact with cable sheath, min 25 years of service in tropical environment Our service 1, Fast Response Time 2, Quality and Certified Products3, Resonable Price 4, Cheap and Reliable Transportation 5, 7*24 Hours After Sales Service

Preformed tension clamp is also called preformed dead end or dead end cable clamp. The raw material of preformed tension clamp is aluminum clad steel wire or galvanized steel wire, For communication ADSS optical fiber, OPGW cable and OPPC. The unique pre-formed tension clamp design not only simplifies the installation but also ensures the safety of the cable connection. Terminal cable clamps provide excellent performance to protect ADSS/OPGW/OPPC cables from stress points and prevent signal drops during transmission. What is the raw material of the pre-formed tension clamp The raw material of the prefabricated tension clamp is aluminum-clad steel wire or galvanized steel wire. What is the purpose of prefabricated tension clamps Prefabricated tension clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. What are the types of prefabricated tension clamps The preformed tension clamp and guy wire dead end grips used on the conductor and earth wire look alike in shape, but there are really big differences in the specification, raw material, and strength requirement of the two types of guy grips. 1. Dead-end for short span ADSS Dead-end for short span ADSS with a small tension clamp material for aluminum-clad gang wire, mainly used for the corner towers, the middle of follow-tower and connecting the terminal tower, the largest installation file from the less than 100 meters. 2. Dead-end for medium/long span ADSS Dead-end for medium span ADSS in tension and large tension clamp material for aluminum-clad steel wire, mainly used for files larger than 100 meters away from the corner tower, the middle tower and Terminal Tower successive connection. As an experienced manufacturer and supplier of preformed tension clamps, Boersen Photoelectric is able to OEM to customer specifications. If you have any questions, please feel free to contact us.

Double Bolt Clamps, Single Bolt Clamps. Four Bolt Clamp and Hose Clips. Industrial Hose Clamps, Heavy Duty Hose Clamps.

ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. ADSS Tension Clamp Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters.