Ft-f1 fogging tester Characteristics: Determines auto's fogging characteristics precisely, guarantees automobiles driving safely. Be applicable for the laboratory and works in low noise. Data test and analysis with professional software, convenient and prompt. Bath temperature controlled by thermostat can be kept constant to 0.1ªc, creating precise testing conditions. Designs friendly and integrally, operates safely and conveniently. World-famous brand elements with stable and reliable performance. The strictly controlled constant thermostat can be used for the other experiments. Conforms to din 75201, iso 6452, sae j1756.
FT-F1 is professionally applicable to the fogging characteristics evaluation of volatile constituents of decorating materials used in cars and aircrafts, e.g. plastic articles, polyurethane, textiles, leather, adhesives, non-woven and thermal forming elastomers at high temperature conditions.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Led bulb, tube light, panel light, decoration light, wall light, steel wires, steel plate, stainless steel plate, twisted wire rods, galvanized wires, wire mesh, site fencing, mosquito mesh, thread rods, rebar, twisted rods, t bar, nuts and bolts, hardware, pvc pipes, upvc pipes, api pipes, melamine, mdf board, plywood, film faced, shuttering, packing, core veneer, face veneer, hdf molded door skin, door filler, tubular particle boards, pvc boards, wpc boards, doors, block board, hard board, gypsum board, canopy, carpet, flooring wooden, bamboo, laminated engineering, tiles, granite tiles, granite blocks, black galaxy, wash basin, water closets, washbasins, ss sinks, faucets, furniture, pvc edge bending, crew, locks, pvc seals, silicone cartridges, shower enclosures, shower door hinges, handles, knobs, brackets, slides, nails, solar panels, flexible solar panels, solar power station, battery, inverters, rechargeable fans, lights, spring, 3ply disposable face mask, oxygen concentrator ,.Buying office, oem, components sourcing, value added services
Gas permeability tester, water vapor permeability tester, tensile tester, heat seal tester, heat gradation heat-sealing tester, coefficient of friction tester, thickness tester, tearing tester, falling dart impact tester, film free shrink tester, airproof tester, digital torque tester, fogging tester, air permeability tester, electrolytic water vapor permeabiity tester.
Code 93100: PE film on nose band for glasses wearer Features Suitable for OR, ER, patient care area, oral, dental procedure, clinics, isolation, IC practices, patients and other applications. Face mask with PE film on nose band for glasses wearer. 1. Type: Flat shape, 3-ply, non-sterile 2. Color: Green, blue, pink, white 3. Outer Layer: Water-repellent non-woven Middle Layer: High level static filtration non-woven Inner Layer: Microfilter thermal-bond non-woven 4. Nose band: PE iron wire 5. Anti-fog film: PE or non-woven material 6. Wear-type: Ear-loop and 4-ties