EDFA Optical Amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). Integrated VOA can be automatically adjusted to achieve smooth gain spectrum. It can amplify the C-Band signal with or w/o middle stage access (MSA), which brings great flexibility for the network application. FUNCTIONï¼? C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1565nm Support systems to achieve different cross-section radio repeater transmission HIGHTLIGHT: Wide operating wavelength range:1528nm~1565nm Three Optical Amplifier C-Band applications: Booster , In-line, Pre-amplifier Low noise figure: typical: 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Many model options serve all the traditional amplifier applications in an extended optical link: booster, in-line, and pre-amplifier. A booster amplifier operates at the transmission side of the link. It features high input power, high output power, and medium optical Gain . Boosters are designed to amplify aggregated optical input power for reach extension. An in-line amplifier operates in the middle of an optical link. It features medium to low input power, high output power, high optical Gain , and a low noise figure. In-line amplifiers are designed for optical amplification between two network nodes on the main optical link. A Pre-amplifier operates at the receiving end of an optical link. It features medium to low input power, medium output power, and medium Gain. Pre-amplifiers are designed for optical amplification to compensate for losses in a demultiplexer located near the optical receiver. Some EDFA Models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility. New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units . Wide operating wavelength range:1528nm~1565nm Dual amplifier contains two independent gain units Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units . Wide operating wavelength range:1528nm~1565nm Dual amplifier contains two independent gain units Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR
Single Fiber Bidirectional EDFA Amplifier models include a Red and a blue port designed for single fiber DWDM Solution. The design of these models is used for single-fiber DWDM transmission systems. C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1561nm Support systems to achieve different cross-section radio repeater transmission Operating wavelength range: Blue: 1528nm~1543nm Red: 1547nm~1561nm Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Offset the insertion loss introduced by DCM Reduce the additional degradation of system OSNR Flexible insertion of DCMs at different distances Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Single fiber bidirectional EDFA amplifier include an Red and blue port, Red optical amplifier include an blue out port and blue in port, Red optical amplifier Amplify red optical signal, blue out port and blue in port are used to access the amplifier to amplify the blue optical signal. Blue optical amplifier include an red out port and red in port, Blue optical amplifier Amplify blue optical signal, red out port and red in port are used to access the amplifier to amplify the red optical signal, Blue: 1528nm~1543nm. Red: 1547nm~1561nm.
EDFA Optical Amplifier 1U Rack EDFA is the erbium-doped fiber amplification board. Its main function is to compensate the power of the signal optical in the transmission line, and it can amplify the optical signals of up to 48 channels with 100 GHZs interval) or 96 channels with 50 GHZ s interval) at C band at the same time. It has characters of flat gain, locked gain, low noise index, etc. It's an indispensable and important component for DWDM system, future high speed system and all-optical network long-distance transmission.
With the application of long-distance systems becoming more and more extensive, our company's self-developed middle stage access (MSA) EDFA, middle stage access (MSA) EDFA can effectively solve the insertion loss caused by DCM and OADM, offset the DCM and OADM bands. The resulting insertion loss reduces the additional degradation of the system OSNR. C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1565nm Support systems to achieve different cross-section radio repeater transmission Wide operating wavelength range:1528nm~1565nm Low noise figure: typ 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Offset the insertion loss introduced by DCM Reduce the additional degradation of system OSNR Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Middle stage access (MSA) EDFA models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility.New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
EDFA Optical Amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). Integrated VOA can be automatically adjusted to achieve smooth gain spectrum. It can amplify the C-Band signal with or w/o middle stage access (MSA), which brings great flexibility for the network application. C-band optical signal overall amplification Covering the wavelength range of 1528 ~ 1565nm Support systems to achieve different cross-section radio repeater transmission Wide operating wavelength range:1528nm~1565nm Three Optical Amplifier C-Band applications: Booster ï??n-line Pre-amplifier Low noise figure: typical: 5dB Excellent gain flatness Multiple operating modes: AGC adjustable Gain APC output is adjustable ACC voltage adjustable Mid-stage access for DCM or OADM Optional OSC channel for remote management MON port, on-line monitoring optical power and OSNR Many model options serve all the traditional amplifier applications in an extended optical link: booster, in-line, and pre-amplifier. A booster amplifier operates at the transmission side of the link. It features high input power, high output power, and medium optical Gain . Boosters are designed to amplify aggregated optical input power for reach extension. An in-line amplifier operates in the middle of an optical link. It features medium to low input power, high output power, high optical Gain , and a low noise figure. In-line amplifiers are designed for optical amplification between two network nodes on the main optical link. A Pre-amplifier operates at the receiving end of an optical link. It features medium to low input power, medium output power, and medium Gain. Pre-amplifiers are designed for optical amplification to compensate for losses in a demultiplexer located near the optical receiver. Some EDFA Models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility. New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology. Some EDFA Models include a Red and a blue port designed for Single fiber DWDM Solution. The design of these models is used for single-fiber DWDM transmission systems.
Erbium-Doped Fiber Amplifier (EDFA) is an optical amplifier used in the C-band and L-band, where the loss of telecom optical fibers becomes lowest in the entire optical telecommunication wavelength bands. Invented in 1987, EDFA is now most commonly used to compensate for the loss of an optical fiber in long-distance optical communication. Another important characteristic is that EDFA can amplify multiple optical signals simultaneously, and thus can be easily combined with WDM technology. Types of EDFA Amplifier 01-1U EDFA Equipment 1U EDFA Equipment has a high stability output power EDFA. The stability Pump Laser and unique ATC(automatic temperature control) and AGC (automatic gain control) circuit are employed in it as the key components to ensure the high stability and reliability of output power. 02-DWDM EDFA Card The multi-channel erbium-doped fiber amplifier(EDFA) features stable output power, low noise, and power consumption. The components of the product are a high-availability pump laser and high-performance gain flattening filters. 03-DWDM EDFA Card with VOA DWDM EDFA Card with VOA input and output signals are sampled and monitored with a feedback circuit. AGC (Automatic Gain Control) circuit is designed into the amplifier to ensure high output power stability and reliability.
Edfa amplifier.R&d, production, export and customer service
High dense space.Ceramic ferrules connector.Low insertion loss.High return loss.Excellent mechanical endurance.High credibility and stability
The 40ch DWDM MUX DEMUX is designed by FIBERWDM, wavelength fromC21 toC60(1560.61nm~1529.55nnm), in accordance with the ITU-T G.694.1 100GHZ grid, it maximizes the capacity of the C-band range. The 40ch DWDM with 1310nm port is totally passive DWDM device, and support low insertion loss( wavelength ports 3.5dB; 1310nm port 0.8dB).And it conjunct with The DWDM amplifiers and DCM device, the 40ch DWDM transfer system can support a long distance transmission.
Optical transceiver, CWDM/DWDM/AAWG, EDFA optical amplifier, OTN, ethernet switches, industrial switches, POE switches, OLP, patch cord .
We are an EU approved CE certified, REACH Certified and RoHS Certified company manufacturer of Optical Brighteners OBA 220 for Paper Industry. We all want our papers to be as white as possible, don't we? Well, that's where optical brightening agents BBU Powder come in. The raw material of paper often consists of impurities such as snippets of bamboo sticks and wood. These impurities dampen the brightness of the paper. We have various Whitening Agent Optical Brightener Available for Paper application like... Optical Brightening Agent OBA 220 in powder form Optical Brightening Agent OBA 220 in Liquid form Optical Brightening Agent OBA 264 in Liquid form Optical Brightening Agent OBA 24 in powder form Optical Brightening Agent OBA 253 in Liquid form Optical Brightening Agent OBA 28 in powder form Optical Brightening Agent OBA 154 in Liquid form Optical Brightening Agent OBA 28 in powder form. Additional Information Physical Appearance : Greenish-Yellow Powder CAS No.: 16470-24-9 EINECS No.: 240-521-2 Specific Gravity / Bulk Density : 0.8-1.0 pH of Liquid or 1% Solution : 8-9 Strength by 100% : 100% Shade/Hue: Bluish white Whiteness/ Brightness : Equal to Std % of Active Substance : 21.95% Absorbance (18mg/l) : 0.217 Moisture Content : 2.40%
We are an EU approved CE certified, REACH Certified and RoHS Certified company manufacturer of Optical Brighteners OBA 220 for Paper Industry. We all want our papers to be as white as possible, don't we? Well, that's where optical brightening agents BBU Powder come in. The raw material of paper often consists of impurities such as snippets of bamboo sticks and wood. These impurities dampen the brightness of the paper. We have various Whitening Agent Optical Brightener Available for Paper application like... Optical Brightening Agent OBA 220 in powder form Optical Brightening Agent OBA 220 in Liquid form Optical Brightening Agent OBA 264 in Liquid form Optical Brightening Agent OBA 24 in powder form Optical Brightening Agent OBA 253 in Liquid form Optical Brightening Agent OBA 28 in powder form Optical Brightening Agent OBA 154 in Liquid form Optical Brightening Agent OBA 28 in powder form. Additional Information Physical Appearance : Greenish-Yellow Powder CAS No.: 16470-24-9 EINECS No.: 240-521-2 Specific Gravity / Bulk Density : 0.8-1.0 pH of Liquid or 1% Solution : 8-9 Strength by 100% : 100% Shade/Hue: Bluish white Whiteness/ Brightness : Equal to Std % of Active Substance : 21.95% Absorbance (18mg/l) : 0.217 Moisture Content : 2.40%
We are an EU approved CE certified, REACH Certified and RoHS Certified company manufacturer of Optical Brighteners OBA 220 for Paper Industry. We all want our papers to be as white as possible, don't we? Well, that's where optical brightening agents BBU Powder come in. The raw material of paper often consists of impurities such as snippets of bamboo sticks and wood. These impurities dampen the brightness of the paper. We have various Whitening Agent Optical Brightener Available for Paper application like... Optical Brightening Agent OBA 220 in powder form Optical Brightening Agent OBA 220 in Liquid form Optical Brightening Agent OBA 264 in Liquid form Optical Brightening Agent OBA 24 in powder form Optical Brightening Agent OBA 253 in Liquid form Optical Brightening Agent OBA 28 in powder form Optical Brightening Agent OBA 154 in Liquid form Optical Brightening Agent OBA 28 in powder form. Additional Information Physical Appearance : Greenish-Yellow Powder CAS No.: 16470-24-9 EINECS No.: 240-521-2 Specific Gravity / Bulk Density : 0.8-1.0 pH of Liquid or 1% Solution : 8-9 Strength by 100% : 100% Shade/Hue: Bluish white Whiteness/ Brightness : Equal to Std % of Active Substance : 21.95% Absorbance (18mg/l) : 0.217 Moisture Content : 2.40%
BrightOmni UP is a Disulpho type Fluorescent Whitening Agent with high affinity for Paper in wet end applications to achieve high whiteness and brightness properties of Paper. It Can be added either batch wise in the mixing chest or continuously at suitable dosing points in the stock preparation system. It Should be applied prior to either alum or cationic auxiliaries. Typical average dosage is 2 - 6 kg/Ton of dry pulp depending on: - Type of furnish - Base pulp pH and brightness - Desired brightness and whiteness gain
Properties 1. Excellent transparency, outstanding resistance to aging. 2. It has good insulating properties and mechanical strength; to acid, alkali, salt has a strong resistance to corrosion; and because easy processing. Applications 1.Extruded sheets for signage, displays and building material 2.Motive parts such as tail lamps, meter covers and sun visors 3.General sundries such as tableware, kitchenware, giftware and bathroom accessories 4.Optical lenses such as sunglasses, reading glasses and camera lenses 5.Light guide panels for LCD displays 6.Other applications such as mobile phone display panels, clock covers, lighting covers/accessories, optical fibres, toys, etc.
HTF launched SOA series optical amplifier products can be 1290nm ~1320nm wavelength range to achieve amplification. It can be easily used in 100G transmission system, the maximum can support 160G/s rate. SOA optical amplifier can be used for booster amplification, pre-amplification and other occasions. O-band optical signal overall amplification Covering the wavelength range of 1290 ~ 1320nm 100G 1310nm signal amplification Support O-band, 1290 ~ 1320nm band amplification Output power up to 10dBm 100G 1310nm signal amplification Support APC Low noise, high gain One board supports up to 2 channels of signal amplification