5. Feed device allows rod to feed out or be wound back onto reel with easy pushi or pull of rod. 6. Duct rods/duct rodders have many applications, not only pulling the cable but also pulling 7. Anticorrosion , good elasticity , long working life. Fiberglass push pull, tracing duct rods, duct rodder--bazhou deli power tools Box
Description: Duct rodders applies in tow lead-rope through a pipe, it is auxiliary means. Surface smooth and high resilience, so the frp perforator with ease passes the narrow channel. Perforator consists of two parts: the glass fiber strengthen the level, the high-pressured low density polyethylene protective layer(smooth, firm , can resist the adverse circumstance).Duct rodders has time-saving reducing effort, improving efficiency, etc, and can be used for telecom cables, cable pipe and cleaning and plastic pipe of cloths to put.When use draws out the fpr pole by the pulley, then with a corresponding metal joint, penetrates in the pipeline. When cleaning, guide-head will drive cleaning tools to clean the pipe;when arranges the cable, you may first leads the steel wire or the iron wire, then enters the pipe with the steel wire or the iron wire hauling cable Fiberglass duct rodder features&benefits: 1. Strong non-conductive fiberglass rod construction 2. Stainless steel drawing head 3. For longer conduit runs and underground duct 4. Rugged tubular steel reel with adjustable position. 5. Feed device allows rod to feed out or be wound back onto reel with easy pushi or pull of rod. 6. Duct rods/duct rodders have many applications, not only pulling the cable but also pulling 7. Anticorrosion , good elasticity , long working life. Fiberglass push pull, tracing duct rods, duct rodder--bazhou deli power tools Box
Fiberglass duct rodder introduction Fiberglass duct rodder applies in tow lead-rope through a pipe, it is auxiliary means. Surface smooth and high resilience, so the frp perforator with ease passes the narrow channel. Perforator consists of two parts: the glass fiber strengthen the level, the high-pressured low density polyethylene protective layer(smooth, firm , can resist the adverse circumstance). It has time-savingreducing effort, improving efficiency, etc, and can be used for telecom cables, cable pipe and cleaning and plastic pipe of cloths to put.When use draws out the fpr pole by the pulley, then with a corresponding metal joint, penetrates in the pipeline. When cleaning, guide-head will drive cleaning tools to clean the pipe;when arranges the cable, you may first leads the steel wire or the iron wire, then enters the pipe with the steel wire or the iron wire hauling cable .
Duct rodder, fiberglass duct rodder, cable pulling, cable snake.
Duct Tape
Fiberglass duct rodder Duct rodder is composed of fiberglass rod which is extruded by fiber glass rod and high strength resin at high temperature. This type of rod has high tensile strength and flexibility. It is covered by a high density polyethylene engineering plastic as it protect layer, which make duct rodder cover sliding on the surface, durable, corrosion resistant and has good insulation performance. Which make them safe for use in cable pulling in the conduit. Duct rodders will equipped with different size reel according to the length of rod. There are wheels on the reel, which could make it easy to move. Features and benefits: Light weight, durable, resistance to acid, aging resistant, corrosion resistant High tensile strength and bending properties, which make it to go through narrow pipes easily. Good temperature adaptability, the product will not soften in hot weather/nor become brittle in cold weather. It is usability will not be affected by temperature. Outer protect layer are made of high density polyethylene engineering plastic, which has good anti-UV capability. cover was coated with long-term UV-resistant polyethylene. it surface has the advantage of smooth, wear-resistant and long service life. There are meter mark on the protect layer of duct rodder. The length is 100m to 400m. There are kinds of colors for the rod to choose. Technical Data of Duct Rodders: 1. Reinforce Fiberglass core Property Data and Value Reinforcement E-Glass Fiber Glass content of inner part 80-85% Material of pulling rod Epoxy fiber glass(inner) and high density polyethylene(outer) Density >150g/m Diameter tolerence ¡À0.10mm Work situation temperature -40 ~ +80 Mechanical properties Property data Min pulling strength 4000N 5% Tensile modulus >30000 MPa Consistency of rod 150g ¡ 5% Flexural modulus >30000 MPa Elongation at Break 2.5-3% 2. Polyethylene cover Material: Medium Density polyethylene resin for the insulating and jacketing of telecommunication cables. Property Data Tensile strength >150N Environmental stress & crack resistance >1000 hr Heat stability ok Carbon Black ok plastic woven 0.5*0.15*0.5m 1.5*0.5*1.5m
Fiberglass duct rodder & snake duct rodder & electric rodder & fiberglass duct rod & duct rodder cable & conduit rodder & cable rodder & push pull rod description: Duct rodder applies in tow lead-rope through a pipe,it is auxiliary means. Surface smooth and high resilience,so the FRP perforator with ease passes the narrow channel. perforator consists of two parts: the glass fiber strengthen the level, the high-pressured low density polyethylene protective layer(smooth, firm ,can resist the adverse circumstance). It has time-savingreducing effort, improving efficiency, etc,And can be used for telecom cables, cable pipe and cleaning and plastic pipe of cloths to put.when use draws out the FPR pole by the pulley, then with a corresponding metal joint, penetrates in the pipeline. When cleaning, guide-head will drive cleaning tools to clean the pipe;When arranges the cable,you may first leads the steel wire or the iron wire, then enters the pipe with the steel wire or the iron wire hauling cable. Fiberglass duct rodder technical specifications: Glass fiber rod diameter 4.5-16mm Length 1-500m Working temperature -40+80 Min Bend Radius 295mm Breaking tension 4.5T Glassfiber density 150g/m 1.constructed of fiberglass reinforced in the center and consists of a rugged plastic layer that would ensure the lifetime of the flexible rod. 2.Excellent flexibility force. 3.Tensile strength about 500 Kgf. 4.designed for heavy duty applications ensuring greater rigidity and strength, while supporting additional forces without resentment to the multiple curvatures. 5.Wheel assembly for easy transportation. 6.Guide rollers and the right parts for rotary coupling. 7.Rolling bearing cage flotation (reel transport) for mobility should be light and easy to use in the field, including a parking brake for the flexible rod. 8. There is copper wire inside for tracing easily. Technical data of duct rodders 1. Glass reinforced composite core: general properties Property value keinforcement E-glass fiber glass content of inner part 75-80% material of pulling rod epoxy fiber glass(inner) high density polyethylene(outer) density >1.9gr/cm3 diameter tolerance +/-0.10mm work situation temperature -40 to +80 Mechanical prperties property value minimum pullling strength 4000 N+/-5% tensile modulus >30000Mpa consistency of rod 150gr/m +/-5% flexural modulus >30000M pa elongation at break 2.5-3% 2. Polyethylene cover Material: Medium density polyethylene resin for the insulating and jacketing of telecommunications cables. property value tensile strength >15N/mm2 environmental stress & crack resistance >1000 hr. heat stability OK. carbon black OK. packed by plastic woven, or wooden pallet. Length 0.5-1.5m Width 0.15-0.5m Height 0.5-1.5m
Fiberglass duct rodder is selected as a special tool for pulling electric cables and optical fibre cables in telecom, power industries, buildings and many other fields. The rod is made of fiberglass and high strength resin at high temperature, it is coated by high density polyethylene engineering plastic as its protected layer, which makes the duct rodder cover sliding on surface, durable, corrosion resistant and has good insulation performance, these make it safe for using in cable occupied duct. Along with pull head and handcart, it features easy to move and operate. The Fiberglass duct rodder will be equipped with different size of reels in accordance with the length of the rod, there are wheels on the reel to make it convenient for moving, it is an ideal tool for laying cables
Fiberglass duct rodder, wheeled duct rodder, portable duct rodder, duct rodder accessory.
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. 14-Nov-16
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod ma
Brief description:As one of biggest duct rodder manufacturers in Asia, we provide the duct rodder with high quality and competitive price. We could produce from 4 to18mm diametersduct rodder, and provide duct rodder adding with copper wire, stainless steel wire for detecting uses. So the duct rodder is also called Detectable Rodders. According to customersrequirement, We could produce different length and colorr duct rodder. Model specification 4.5mm,6mm,8mm,10mm,11mm,12mm,13mm,14mm,15mm,16mmfor your choice, and we can also accept OEM order Length 30,50,60,80,100,120,150,180,200,250,300,350,400,450,500 meters for choice. Material Fiberglass (inner) and high density polytgtkebe(outer) Density >1.9gr/cm3 Working temperature - 40 to + 80 Minimum pulling strength 4000 N5% Tensile Modulus >46.500Mpa
Fiberglass Duct Rudders & Fish tapes Fiberglass Duct Rodder Duct Rodders are composed of fiber glass rod which was extruded by fiber glass and high strength resin at high temperature. This type of rod has high tensile strength and flexibility. It was covered by a high density polyethylene engineering plastic as its protect layer, which make duct rodder cover sliding on surface, durable, corrosion resistant and has good insulation performance, which make them safe for use in cable occupied duct. High Density polyethylene (Grade: for the insulating and jacketing of Telecommunication Cables) is used in the outer diameter coating. Duct Rodders will equipped with different size reel according to the length of rod. There are wheels on the reel, which make it convenient for moving. Light weight, durable, resistance to acid, alkali, aging resistant, corrosion resistant. High tensile strength and bending properties, which make it to go through narrow pipes easily. Good temperature adaptability, the product will not soften in hot weather / nor become brittle in cold weather. Its usability will not be affected by temperature. Outer protect layer are made of high density polyethylene engineering plastic, which has good anti-UV capability. Cover was coated with long-term UV-resistant polyethylene. Its surface has the advantage of smooth, wear-resistant and long service life. There are meter marks on the protect layer of duct rodder, which can be used for measuring distance. Marks are printed by professional printing machine, which has the advantage of strong adhesion, clear writing, waterproof, anti-ultraviolet, it can be still clear even after using many times. There are several kinds of colors for the rod for your chosen.
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod ma
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod may cause increased friction in the tighter bends.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Flame retardant cloth thath as excellent flexibility used to seam,seal, repair cargo compartment liners, cover pin and rivets. Adheres well to steel and plastic Coated on the water proof to havea very high fracture resistance and paste strength. 2" 24pcs/ctn Product origin : UAE
Duct Tape
Cable pulling rod & push duct rodder & fiber snake rod Epoxy duct rodder is the continuous rods sizes are 4.5mm 6mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm, the duct rodders¡¯ lenghth is range 50m to 400m. Duct rodders/rods features Strong non-conductive fiberglass rod construction Stainless steel drawing head For longer conduit runs and underground duct Rugged tubular steel reel with adjustable position. Feed device allows rod to feed out or be wound back onto reel with easy pushi or pull of rod. Duct rods/duct rodders have many applications, not only pulling the cable but also pulling electric tools, and it repair is very easy, and available. Glass fiber rod diameter 4-16mm Length 100-400m Working temperature -40 ~ +80 Min bend radius 390mm Breaking tension 4500-9000kg Glassfiber density 150g/m Plastic woven 0.5*0.15*0.5m 1.5*0.5*1.5m
