hand water pumps ... 600g per pcs ;output pressure 0.25Mpa, used on boat for pumping water....
We Supply Wide Variety Of Pumps To Our Valued Customer All Over The World. Our Customers Manly From Power, Steel, Sugar, Paper, And Chemical Industries. Few Types Of Pumps Are Listed Below. Please Refer Our Brands Section For Checking Out Our Pump Brands End Suction Pumps Split Case Pumps Multi Stage Pumps Sump Pumps Vacuum Pump Submersible Pumps
hand water pumps ... 600g per pcs ;output pressure 0.25Mpa, used on boat for pumping water....
Diaphragm Pump
TONSON Pneumatic double diaphragm pump is designed for volatile and hazardous chemicals to be explosion-proof, absolutely safe, convenient, saving you time and money. It can be installed without power supply and fastness. The material includes aluminum alloy and stainless steel.
Diatax Pump Diaphragms - Industry Standard Diatax pump diaphragms are produced from the highest quality materials and precision molds to ensure a long service life for this â??heart valveâ?? of the diaphragm pump. Diatax rubber/fabric-reinforced and thermoplastic (TPE) pump diaphragms offer a combination of performance and economic benefits including superb flex fatigue resistance, excellent abrasion resistance, and good temperature resistance. Increased flex life results in less downtime, lower maintenance costs and lower replacement costs for the pump user. Diatax pump diaphragms have set the industry standard for years. Our Diaphragms are suitable for - Slurry Pumps Dosing Pumps Metering Pumps Air Operated Double Diaphragm Pump (AODD Pump) Submersible Pump Actuators Pump Vacuum Pump Spray Pumps Our size ranges from 5mm to 1500mm Diameter in various shapes as per clientâ??s requirement. Our Diaphragms have been tested up to 28 kg/cm2 working pressures and operated up to a million flex cycles. Our speciality is to design, develop, prototype Rubber Diaphragms as per your specific requirements/service conditions. Grades of Rubber used for different applications are Chloroprene (Neoprene), NBR (Nitrile), EPDM, Butyl, Hypalon, Silicone & Viton. These Diaphragms are suitably reinforced as per clientâ??s service and requirement with Cotton Canvas, Nylon Fibre, Polyester, Metal Mesh, Glass Fibre, Tyre cord etc. The Grades of Rubber are offered in respect to various services i.e. Hot Water, Steam, Low permeation gases, Ozone resistance, Oil and fuel resistance, Cryogenic applications etc. Please refer our Chemical service resistance chart as well as our general-purpose polymer chart for guidance.
Pumps have an inlet, outlet Aluminium, and Plastic (Polypropylene) casings and they have more utilization areas in waste water treatment, chemical industry, oil&gas applications and also food&pharmacy, new energy, etc. With good performance at energy saving, low working noise, low-pressure start-up ability, etc.
Model:DDP-2 INSTALLATIONS AND USE . The pumps are compact and designed for a wide range of applications including liquid transfer, spraying , circulation, filtration and dispensing. . This compact automatic demand water system pump has a builtâ?�in pressure switch, which automatically starts and stops the
Salient Features Highly efficient 3-Phase Water Filled Motor - 100% EC grade copper winding - Easily Rewindable - Motor Designed with Higher Cooling Effect Ensures Longer Life - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Zero maintenance Product Specification Power Range : 3.0 HP to 10.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 â?? 50 Hz Input Solar DC Power Range : 3000 Wp, 10000 Wp Input Solar DC Voltage Range : 330 Vmp , 600 Vmp Head Range : 10 Mtr , 50 Mtr Discharge Range : 126000 LPD , 425000 LPD Type of Duty : S1 Material Of Construction Part Grade Oil Seal : Nitrile butyl rubber Motor Shaft : SS - 420 Motor Body : Cast Iron / J4 Motor Bush : LTB-4 / Teflon Thrust bearing assembly : SS - 420 & Carbon Base : Cast Iron Bracket : Cast Iron Flange : Cast Iron Casing : Cast Iron Impeller : Cast Iron
Highly efficient 3-phase Air Cooled motor - 100% EC grade copper winding - Easily Rewindable - Good suction lift characteristics - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Double shielded ball bearings, so no need of external lubrication - Mechanical seal or stuffing box is provided as per customers requirement - Zero maintenance Product Specification Power Range : 1.0 HP to 10.0 HP Operating Speed : 0 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 10000 Wp Input Solar DC Voltage Range : 110 Vmp, 600 Vmp Head Range : 10 Mtr, 50 Mtr Discharge Range : 45000 LPD - 405000 LPD Max. Suction Head : 7 Mtr Type of Duty : S1 Material Of Construction Part Grade Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
double tube hand pump for BIG SUP board TRIPLE ACTION it's more compact and light. It's the best for brands who want to use a pump of triple action as standard equipment in their SUP. The compact piston permits also females and young guys to be able to achieve easily high pressure. HP6, being used in TRIPLE-doublesingle action, can achieve 30psi rapidly and effortlessly. The switching 3-2-1 can be realized easily and comfortably rotating the switch knob. Itâ??s completely customizable for colour, graphic and calibration of gauge meter. Features: · capacity 3.2+3.2L, max. pressure 30psi as DIN EN 16051 · switch knob to change comfortably from triple to double or single seals and anti-sand filter for long life of pump and SUP extra long body and high-airflow piston for an easier inflation pump completely shock-proof, compact and light (1.7kg) · shockproof gauge meter
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum