Short Description: CR 6032 series intelligent boiler level sensor is based on capacitance measurement principle. It uses positron-emission tomography technology to measure and analyze the dielectric constant of liquid and vapor medium,temperature,pressure and other parameters in the cylinder, After the microprocessor processing, the output conforms to the industrial standard 4-20mA current signal,RS485 digital signal can also be output. Liquid level sensor compensates automatically in real time during operation without the affect of temperature, pressure, medium changes, good long-term stability. It is a full working condition, high cost performance drum level sensor which is suitable for boiler drum of generator set water level measurement like power plant, steel plant, cement plant. Technical features Two-wire system, 4-20mA current loop, with a resolution of 0.1 mm and accuracy higher than 1%. With tomographic, it can make continuous measurement and compensation for dielectric constant variation of liquid and vapor mediums. With patented automatic calibration technology, it can automatically align the zero and full points in the process of emptying and water-adding of the liquid level meter. The measurement is true and reliable due to that the level meter is directly connected with the drum body of boiler and the capacitive sensor is in direct contact with the liquid. The patented structure of steam condensing chamber can ensure the consistency of the temperature between the level meter and the boiler drum body to the maximum extent, so as to ensure the accurate of the water level measured. It can also effectively separate the steam from the water to prevent water drop on the surface of capacitive sensor, and avoid the impact of steam and water on the capacitive sensor. Its inverted structure and automatic sealing function ensure the safety and reliability of the electrical parts. It adopts advanced technologies for the whole parts, and is reliable and durable. CR-6032Technical Indicators Power: Max: 28V Min: 15V Typical: 24V Current loop: two wire, 4.00mA~20.00mA (±1%) Explosion-proof grade: ExiaIICT6 Explosion-proof parameters: Ui=30V,Ii=100mA,Pi=0.75W,Ci=100pF,Li=10uH Working pressure: 6.5MPa max Detection range: 1500mm Measurement period: 0.1 Environment temperature: -40~85 Medium temperature: 450 Max IP grade: IP65
Short Description: The intelligent boiler level sensor is an economical boiler level sensor designed for small and medium-sized boilers. Based on radio frequency capacitance measurement technology, the product outputs 4-20mA continuous standard signal, which is used for accurate measurement and control of liquid level of small and medium-sized boiler drum. The liquid level sensor integrates high temperature resistance, high pressure resistance, corrosion resistance and anti-fluctuation performance together. The transformer part uses military devices to make the signal output more stable and reliable. The liquid level sensor is simple to install, maintenance quantity little, measurement and control accurate, cost-effective. It is the ideal replacement products of traditional differential pressure type, electrode type, magnetic flip plate type liquid level sensor
Bronze Sleeve Packed Water Level Gauge Rating : Max. BOP 250 PSIG (17.24 Bar) at 435 F (225 C) Material : Bronze Description : Consisting of Steam Arm, Water Arm, Drain Cock, Left & Right Hand Type Ends : Screwed Specials : IBR Item Code : BM000057, BM000058 Size : 15mm Notes : Available Valve Size : 15mm to 20mm
Bronze Sleeve Packed Water Level Gauge Rating : Max. BOP 250 PSIG (17.24 Bar) at 435 F (225 C) Material : Bronze Description : Consisting of Steam Arm, Water Arm, Drain Cock, Left & Right Hand Type Ends : Flanged Specials : IBR Item Code : BM000055, BM000056 Size : 15mm Notes : Available Valve Size : 15mm to 20mm
Carbon Steel Sleeve Packed Water Level Gauge Rating : Max. BOP 350 PSIG (24.1 Bar) at 800 F (427 C) Material : Carbon Steel Description : Consisting of Steam Arm, Water Arm, Drain Cock, Left & Right Hand Type Ends : Flanged Specials : IBR Item Code : BM000053, BM000054 Size : 20mm
- Material : polyethylene - Coating : Polyurethane Coating-Palm - Size : 7, 8, 9 - Packaging : 1pair- Individual packing, 1pack=12pair, 1box=12pack - Gauge : 13 - Purpose : Cut Resistant (Cut Level 3)
- Material : Stainless Steel Core, Polyethylene Yarn, Span Yarn - Number of Stitiches : 10 Gauge - Length : 14 inch - Cut Level : 5 - Color : Gray, Black, White - Packing : 1pair/individual packing (1pack=5pair, 1box=200pair) - Origin : Made in South Korea - Purpose : Cut Resistant
FRP920 OPEN Fishing Boat With Consone Centre Console Boats Fishing Boats Specification Length: 920cm/ 30ft Beam: 230cm / 7.6ft Net Weight: 1400kg Passenger: 12 People Recommend power:150-300 hp Speed: 30 to 43knot Fuel Tank: 240L No of Engine: Single or Twins Standard Feature and Accessories 1) Fiberglass materials, White color boat hull and deck 2) Half open small cabin console and seat 3) Stainless Anchor column and 4pcs Anchor for rope. 4) Stainless Handrails 5) Steering system 6) Navigation lights, horns 7) 240L inside fuel tank (with oil level gauge) 8) bilge pumps 9) Rubber fender 10) Fiberglass fore and stern storage
We are specialized manufacturer of different kinds of sight glass ,gauge glass and related gasket in China.our products have been exported to Pakistan, Poland, Croatia, Malaysia, USA, Syria, Vietnam, Netherlands, UK, Bulgaria and so on. And we are keeping the long term cooperation relationship with our clients Our main product: 1) Reflex type Gauge glass 2)Flat type Gauge glass 3)Round type sight glass 4)Glass tube 5)Gasket for Gauge glass & sight glass 1)Gauge glass sizeï¼? 340 x 34(30) x 17mm; 320 x 34(30) x 17mm; 280 x 34(30) x 17mm; 250 x 34(30) x 17mm; 218 x 34(30) x 17mm; 190 x 34(30) x 17mm; 165 x 34(30) x 17mm; 140 x 34(30) x 17mm; 115 x 34(30) x 17mm The other size is optional or according to the requirements of customers. 2)Round sight glass size: Diameter: 30~350mm, thickness:10~30mm The other size is optional or according to the requirements of customers 3)Glass tube size: Outside diameter: from 3mm to 315mm.Wall thickness: from 1.0mm to 10mm.Length: from 5mm to 2200mm. Normal length: 1000mm-1800mm Such as print the words on the products, the size, and so on.
CR-6011 series cable type liquid level gauge is made of soft PTFE sheathed high temperature coaxial cable as sensor wire. It has the characteristics of transportationï¼?convenient installation, etc. It is suitable for continuous measurement of conductive medium under medium and low voltage reservoirs, sewage, high-temperature groundwater and acid-base solution level. It has a wide measuring range and good performance-price ratio. The core components of the product use advanced video capacitance detection circuit to convert into a standard signal (usually 4-20mA) after 16-bit single-chip microcomputer through precise temperature compensation and linear correction. All series of transmitters have on-site calibration function, users can automatically adjust the zero pointand rangeby pressing the button to adapt to the different requirements of various complex places. The product complies with GB3836.4-2000 Explosive gas environment electrical equipment part 4 intrinsic safety type iand GB3638.1-2000 explosive gas environment electrical equipment part 1 general requirementsexplosive-proof mark: ExdIIC T6, it applicable to the areas of Zone 0, Zone 1, and Zone 2 containing IIA~IIC, T1~T6 explosive gas mixture, and qualified by the National Explosion-proof Electrical Gas Quality Inspection Center, and obtained the explosion-proof certificate. Performance Range:0.2-30m Working medium: water, sewage ,acid and alkali solution Accuracy: 0.5 Pressure range:-0.1Mpa~1Mpa output signal:4-20mA, 4-20mA with HART communication, 485 communication,CAN bus communication Fixation: Screw mounting M20Ã?1.5ã??M27Ã?2ï¼? Flange mounting DN25ã??DN40ã??DN50.Special specifications can be customized Probe temperature resistance:-50~80 Storage temperature:-55~+125 Supply voltage:12-28VDC(Intrinsically safe type needs to be powered by safety barrier) Fixing method:thread mounting:M20*1.5M27*2 Explosion-proof grade: intrinsically safe Exia IIC T6 flameproof ExdIIC T5 Protection level:IP67 Intrinsic safety parameters: Ui: 28VDC, Ii: 93mA, Pi: 0.65W, Ci: 0.042uf, Li: 0mH
CR-6011 series cable type liquid level gauge is made of soft PTFE sheathed high temperature coaxial cable as sensor wire. It has the characteristics of transportationï¼?convenient installation, etc. It is suitable for continuous measurement of conductive medium under medium and low voltage reservoirs, sewage, high-temperature groundwater and acid-base solution level. It has a wide measuring range and good performance-price ratio. The core components of the product use advanced video capacitance detection circuit to convert into a standard signal (usually 4-20mA) after 16-bit single-chip microcomputer through precise temperature compensation and linear correction. All series of transmitters have on-site calibration function, users can automatically adjust the zero pointand rangeby pressing the button to adapt to the different requirements of various complex places. Performance Range:0.2-30m Working medium: water, sewage ,acid and alkali solution Accuracy: 0.5 Pressure range:-0.1Mpa~1Mpa output signal:4-20mA, 4-20mA with HART communication, 485 communication,CAN bus communication Fixation: Screw mounting M20Ã?1.5ã??M27Ã?2ï¼? Flange mounting DN25ã??DN40ã??DN50.Special specifications can be customized Probe temperature resistance:-50~80 Storage temperature:-55~+125 Supply voltage:12-28VDC(Intrinsically safe type needs to be powered by safety barrier) Fixing method:thread mounting:M20*1.5M27*2 Explosion-proof grade: intrinsically safe Exia IIC T6 flameproof ExdIIC T5 Protection level:IP67 Intrinsic safety parameters: Ui: 28VDC, Ii: 93mA, Pi: 0.65W, Ci: 0.042uf, Li: 0mH
Working principle The product consists of a body, a flap box (composed of red and white two-color magnetic small flaps), a float, a flange cover and a liquid level transmitter. The structure is shown in the figure. The working principle is as follows: the external flap box and the transmitter are subjected to the floating body(with a directional magnetic source, which is developed according to different media and pressure)of itself turn the flipper to display red and white color, and the float is provided. The movement indicates different liquid level heights, and the liquid level transmitter transmits the liquid level signal to the control center for liquid level indication and control, and can also be centrally monitored by a computer. 437 Main technical index Measurement rangeï¼?300~19000mm Media density: 0.5ï½?2g/cm3 working temperature:-40ï½?350 Pressure grade:â?¤32MPa Measurement accuracy:â?¤±10mm Transmission distance:1000m Features and applicable places Suitable for high temperature, high pressure, strong acid, strong alkali and explosion-proof requirements, simple structure, reliable and durable, can be installed with a variety of optional accessories to make control easier. Install liquid level transmitter and magnetic switch, can be installed or adjusted at any time without stopping the machine If the power supply is interrupted, the field magnetic switch will not be affected, high accuracy. Add a color patch of different colors every 10 cm to make the liquid level easy to identify. Suitable for waste water treatment, power plants, chemical equipment, thermal kerosene boilers and petrochemical industries.ã?? ordering instruction 1 Model Specifications 2ã??Name and density of the medium under test 3ã??Working pressure 4ã??Working temperature 5ã??Measurement range 6ã??Joint flange (standard) 7ã??Matched instrument 8ã??Special requirement 20170822204423_5937
Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.
Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a dirty oil product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.
Mazut-100 is a fuel oil that is manufactured to GOST specifications, for example GOST 10585-75/99. GOST is the Russian system of standards. Mazut is almost exclusively manufactured in the Russian Federation, This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product has a high viscosity which drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: - "Very Low Sulphur" is mazut with a sulphur content of 0.5% - "Low Sulphur" is a mazut with a sulphur content of 0.5-1.0% - "Normal Sulphur" is a mazut with a sulphur content of 1.0-2.0% - "High Sulphur" is a mazut with a sulphur content of 2.0-3.5% - Very Low Sulfur mazut is generally made from the lowest sulfur crude feedstocks.
Chart recorders Gas analysing meters & detectors Load cells & display units. Instrumentation: flow, level & pressure control equipment for all industrial processes & mediums Vacuum switches generators & pumps Pressure gauges
The main copper sulphide minerals are chalcopyrite (CuFeS2) chalcocite (Cu2S), covellite (CuS), bornite (Cu5FeS4), tetrahedrite ((Cu,Fe)12Sb4S13) and enargite (Cu3AsS4). The largest source of copper is from porphyry ore deposits in which one or a combination of the minerals occurs. A typical copper sulphide ore contains various levels of iron sulphide types that generally include pyrite (FeS2) and pyrrhotite (Fe1-xS). Often gold and silver are present which may either be associated with the sulphides or are free. The gangue particles can consist of a range of silicate minerals from quartz to talc and clays. Item Specification CR2O3: 42% Basis: 40% Min CR/FE Ratio: 1.35:1 MGO: 14% Max AL2O3: 16% Max SIO2: 10% Max P: 0.01% Max S: 0.01% Max Size 0-2 MM: (95% Min) Moisture at 105C or 110C: 8% Max
Product advantages: ï?¬All-in-one design, high integration and space saving installationï¼? ï?¬Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 yearsï¼? ï?¬Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics Built-in BMS management system with comprehensive protection and monitoring control functions 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells Main control MCU can be centrally controlled and manage peripheral settings (AC charging module, inverter module, solar charging module) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable BMS battery management system, with SOC automatic calibration and high current passive balance function, combined with perfect operation control and management strategy, to achieve accurate and efficient management EMS energy management system, BMS with solar controller/AC charger, inverter centrally manages charge and discharge, effectively controls the charge and discharge current within the cell usage conditions, protects the cell and extend its service life
1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 10 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 11 Built-in BMS management system with comprehensive protection and monitoring control functions 12 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 13 Main control MCU can be centrally controlled and manage peripheral settings (AC charger, inverter, solar charger) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
Product Features: 1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 1 Small size and light weight, Maintenance-free 2 Environmental protection and pollution-free materials, no heavy 3 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 4 Built-in BMS management system with comprehensive protection and monitoring control functions 5 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 6 Main control MCU can be centrally controlled and manage peripheral settings (AC charging module, inverter module, solar charging module) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
