JH series gear reducers for cement kilnsare involute cylindrical gear units with parallel shafts which has four reduction stages.This series has four basic structure including over 50 types.Thanks to the standardized,series and modulated design,the reducers can be manufactured according to standard or specific requirements at customers'choice with good reliabiity and maintenance.
Type of wood: birch, alder, ash, hornbeam, oak
Length: 25 cm
Moisture content: 10-18%
Bag size: 40cm x 60cm
Weight of a bag: 8-12 kg
Transportation options: Container or truck
INCEPTION: G- GROUT MF-8 is highly fluid, single component, cementitious grout pre packed .
G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks, pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality.
PURPOSE: G- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. �·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with water
BENEFITS: G-GROUT MF-8 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly & Cost Effective.
TECHNICAL SPECIFICATION
METHODS OF USES: Pre-process-
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
Mixing:
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
PACKAGING G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
STORAGE G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice
Construction & Build
Body Material: Stainless Steel (SS 304 inside / SS 202 outside optional)
Insulation: High-density mineral wool (80 - 120 mm)
Door Type: Single front door with heat-resistant glass & silicone gasket
Chamber Type: Fully welded, corrosion-resistant baking chamber
Capacity & Dimensions
Tray Capacity: 42 Trays
Tray Size Compatibility: 400Ã??600 mm / 460Ã??720 mm (customizable)
Rack Type: Rotary trolley system (single rack)
Baking Capacity: Approx. 150â??200 kg per batch (depending on product)
Heating System
Fuel Options: Diesel / Gas (LPG / PNG) / Electric
Burner Type: Imported or Indian high-efficiency burner
Heat Distribution: 360 uniform hot air circulation
Temperature Range: 0C - 300C
Heating Time: Fast preheating (15 - 20 minutes approx.)
Airflow & Baking Performance
Fan System: Heavy-duty blower motor
Air Circulation: Even baking across all trays
Rotation System: Motorized rotating rack for uniform baking
Steam System: Built-in steam generator for bread & buns
Electrical & Power
Power Supply: 3 Phase, 380â??415V, 50/60 Hz
Connected Load: Approx. 3â??5 kW (excluding burner)
Control Panel: Digital / PLC-based (optional touchscreen)
Control & Automation
Control Type: Semi-Automatic / Fully Automatic
Features:
Digital temperature control
Timer with alarm
Programmable baking cycles (PLC models)
Auto steam injection
Safety Features
Overheat protection
Emergency stop system
Door safety switch
Flame failure safety (for gas/diesel models)
Applications
Bread, buns, rusk
Cakes, muffins
Cookies, biscuits
Puff & bakery items
Export Features
CE-compliant design (on request)
Heavy-duty motors for continuous operation
Easy installation & low maintenance
Suitable for commercial & industrial bakeries
