BF-630 is one of CHIYU Technology's Fingerprint, single door access controller with Web Bbased. Ideally, BF-630 is used to manage entrance security or a small office as a simple time attendance recorder with Fingerprint or RFID and Password. IP Based with embedded Web Server Optical based fingerprint sensor Lower power consumption, OSD menu (On Screen Displayer) Voice indication module option Fire Alarm/ Door Sensor USB device option (for logs extraction) Double Badges and Interlocking Anti Pass Back unlimited levels Fingerprint + Pin/ Card + Password/ Lock Release/ Exit button Time zones 50 Holidays/ 40 Function Keys/ 32 Departments,Designations, Groups 64 Time Sets and Time Zone ► Technical Specification Verification Option Fingerprint Fingerprint + Card Fingerprint + Pin Card + Pin Fingerprint + Card + Pin Verification Mode 1:1 /1:N Verification Time Less than 2.0 sec Registration Time Less than 3.0 sec Capacity 950 persons, totally 1900 templates (2 templates/ Users) Log Data 32,768 System Log 2,000 Relay Output 2 Reset Button 1 Sensor Input 1 Communication Interface RS-485×1 →Relay Box (BF-20/ BF-50) TCP/IP (Reserved for internetworking) WG In & Out 26/ 34 bit Communication speed Ethernet 10/100M, Auto crossing Card format 125 KHz (EM/TM) 13.56 MHz Reading Range 7 ~ 12cm (EM/TM) 3 ~ 5 cm (Mifare) Language Traditional/ Simple Chinese/ English Keypad 10 numeric keys (0~9) + 6 function keys (F1~F4,#,*) & 1 Door Bell Display 128 × 64 Dots LCD Operation Temperature 0℃~ 65℃ Operation Humidity 5% ~ 95%RH Dimension 125 × 145 × 33 mm Weight 360 g.
About THE Product : Blast furnace slag is used in the production of cement (iron Portland and blast furnace cement). Air-cooled blast furnace slag is formed by allowing the molten slag to cool relatively slowly under ambient conditions; final cooling can be accelerated with a water spray. The cooled material is hard and dense, although it can have a vesicular texture with closed pores. After crushing and screening, air-cooled slag can be used in several applications. Granulated slag is formed by quenching molten slag in water to form sand-sized particles of glass. The disordered structure of this glass gives the material moderate hydraulic cementitious properties when very finely ground into granulated blast furnace slag, but if it can access free lime, the granulated blast furnace slag develops strong hydraulic cementitious properties. Pelletized or expanded slag is cooled through a water jet, which leads to rapid steam generation and the development of innumerable vesicles within the slag. The vesicular texture reduces the overall density of the slag and allows for good mechanical binding with hydraulic cement paste. Blast Furance Slag is a nonmetallic co-product which is produced in the process of iron manufacturing, Granulated Blast Furnace Slag is a glassy granular material formed when molten blast furnace slag is rapidly cooled by direct water. Rapid cooling prohibits the formation of crystals and forms glassy, non-metallic, silicates and alumino silicates of calcium. GBFS : (Granulated Blast Furnace Slag) Source : Granulated BF Slag From Gujarat State, India Supply Quantity : 50,000 Metric Tons Per Month Packing: Bulk Parameters (% BY MASS) CaO 30-38 Al2O3 15-20 SiO2 30-40 Glass Content 85-97 MgO 8-11 Fe2O3 0.5-1.5 Moisture 10 MAX Size -5mm Min 95, +5 mm Max 5 Relative Gravity 2.9 Bulk Density(Bagged) 1200 KG/M3
Ouzim BioEngine2 Biometric Fingerprint Access Control for security entrance solution Model: BioEngine2 Supports multiple authentication multifunction: fingerprint, passcode and cards. 1. 3,000 fingerprints +3,000 cards +3,000 passcode + 200,000 records 2. Support Mifare card 13.56 MHz +ID card 125KHZ 3. 360-degree rotation identification, high sensitive to identify. No need film cover on the sensor 4.
Pepper export from Vietnam is considered as the biggest supply all over the world, contributing 1/3 of global production and over 50% of trade volume (about 150,000 tons per year). CET GROUP JSC is one of the leading exporters in VIETNAM Understanding that quality is the key to ensure long-term and repeated orders, our experienced team is working hard with supported by many big Manufacturers in Vietnam with the most modern technology imported from Europe and two dedicated cleaning lines, a steam sterilization machine. We can commit a high standard of pepper to specific requirements. - Capacity: 20,000 MT per annum. CET GROUP JSC can supply all grades of pepper whole including: For Black Pepper: Grades available: Fair Average Quality (FAQ), Machine Cleaned (MC), ASTA 560/570 g/l, 5mm bold, Steam sterilized (HTST), Rainforest Alliance pepper (RA). 500 G/L, 550 G/L, 570 G/L, 580 G/L, 570 G/L BOLD Moisture: 12.5% max Foreign matter: 0.2 - 1% For White Pepper: Grades available: White pepper 630 G/L DW FAQ, White pepper 630 G/L DW machine cleaned, White pepper 630 G/L DW steam sterilized (HTST). Moisture: 12.5% max Foreign matter: 0.2 -1% Black bean: 3% max PACKING: With the automatic packaging line controlling metal, our facility can supply all size of packaging from slack bags of 25 kg, 50 kg, 60 kg or 50 lbs to bulk bags of 500 kg, 625 kg, and 725 kg. Packaging materials are PP bag, jute bag or paper bag.
Turkey Starter Feed (T-030424) (Feed from 12-18 Weeks) Vitamin-enriched Turkey Grower Feed is accessible in granule form. Brown in color, this feed provides 4.0% fat, 3.4% fiber and 19.4% protein in their crude form. This fodder contains up to 5.5% insoluble ash. This feed has been produced from ingredients like trace minerals, essential amino acids, soy meal, minerals, wheat based and corn based gluten, toxin binder, DDGS, grains, pulses and mold inhibitors. Offered Turkey Grower Feed has pure vegetarian content and it is accessible in pellet or coarse mash form. Product Details : Crude protein (N x 6.25)� (maximum %) :� 19.4 Crude Fat� (maximum %) :� 4.0 Crude fibre� (maximum %) :� 3.4 Moisture� (maximum %) :� 12 Acid-insoluble ash� (maximum %) :� 5.5 GENERAL DETAILS Ingredients :� Corn Gluten Meal, Wheat Gluten, Soy Meal, DDGS, Grains, Pluses, Essential Amino Acids, Vitamins, Minerals, Trace Minerals, Toxin Binders and Mold Inhibitor Ingredient Profile :� 100% Vegetarian Moisture (% Maximum) : 12 Product Form :� Coarse Mash Form / Pellet Form Product Branding : HAF Net Weight :� 39 Kgs When Packed Product Pricing :� On Unit Basis (for each 39 Kgs Packing) Production Capacity per Day :� 450 MT/Day Factory Visit :� Not Permissible Fumigation :� Aluminum Phosphide or Methyl Bromide (or any as per buyer specification) Clinical Test Methodology :As per IS:2052 Proximate Analysis on Dry Matter Basis We are prominent manufacturers and suppliers of a qualitative range of Turkey Grower Feeds. Our products are widely demanded by clients owing to its high nutritional value and safe consumption. Manufactured under the firm direction of quality controllers these products ensure longer shelf life and effective usage. one can avail these products in various sized packaging. We offer our products at market leading rates.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
We are suppliers of best quality food spices like White and Black pepper,whole cardamom,Cloves,Coriander seeds,Onion,Garlic,Nutmeg,Cinnamon ,Cumin ,Cassia and other food spices. We have been in business for over 5 years know and with buyers globally. We are looking for serious buyers that are in need of our product get in contact with us.Our company is one of the leading suppliers of spices. 1.Black pepper Black pepper 500 g/l FAQ: -Density: 500 g/l min -Moisture: 13.5% Max -Admixture: 1% Max -Loading: 13.5 MTS/ 20 feet container. -Piperine: 4 % min Black pepper 500 g/l Cleaned ASTA: -Density: 500 g/l min -Moisture: 12.5% Max -Admixture: 0.2 % Max -Loading: 14 MTS/ 20 feet container. -Piperine: 4 % min Black pepper 550 g/l FAQ: -Density: 550 g/l min -Moisture: 13% Max -Admixture: 0.5% Max -Loading: 15 MTS/ 20 feet container. -Piperine: 4 % min Black pepper 550 g/l Cleaned ASTA: -Density: 550 g/l min -Moisture: 12.5% Max -Admixture: 0.2% Max -Loading: 15 MTS/ 20 feet container, -Piperine: 4 % min Black pepper 5mm bold : -Density: 570-580 g/l min -85% on sieve 5 mm -Moisture: 12.5% Admixture: 0.2% max Loading: 15 MTS/ 20 feet cont 2. White pepper White pepper 630 g/l double washed: -Density: 630 g/l min -Moisture: 13.5% Max -Admixture: 0.2% Max -Loading: 18 MTS/ 20 feet container, -Piperine: 4 % min Pinhead 1 mm -2 mm (85% on screen): -Moisture: 13.5% -80% on screen 1 mm -Loading: 8 MTS/ 20 feet cont; 20 MTS/40 feet cont -Packing: 25 kgs/pp bag Black pepper�¢??s husk: Quality like per samples Packing: 25 kgs/ pp bag Valid:within 1 days 2. Delivery: promt shipment (7-14 days from the supplier received the deposit) 3. Packaging: 50kg/bag or customer�¢??s require 20 feet container =13.5 MTS 4. Payment: L/C irrevocable at sight 100% or T/T 30% advance, 70% balance after send email copy shipping documents. 5. Inspection: S.G.S, ICC control or as your request We do hope to have a chance cooperate with you and develop it Thanks and Best Regard!
1.Size:15cm*9cm*3.5cm 2.Weight:0.8kg 3.Material: metal 4.Verification speed:
1. Size:15cm*9cm*3.5cm 2. Weight:0.8kg 3. Material: Metal 4. Verification Speed:
3,000 fingerprints, 80,000 records I/O interface: RS485, USB, TCP/IP RF ID card capacity: 30,000 Recognition mode: F/P/C/F+P/F+C Hardware: 400MHz ARM9 processor Compact and streamline design, metallic baking finish 4-direction cable output Larger LCD: 132 x 64 pixels (W92 x H45mm) 1.8 x 1.8cm 500dpi optical sensor Prompt info display on device: such as department, title, or other company notification Intelligent self-learning With additional charge, the most fingerprint capacity could be extended to 30,000 & 120,000 records Software: Auto-calculation of report/fingerprint data (timer setting) On line upgrade Auto back-up data (timer setting) Auto read log-data Auto-calculation of report/fingerprint data (timer setting) Upload registered fingerprint data to multiple devices at same time Direct data import of staff information from an existing Excel file Multiple database management, the headquarter can directly check T&A status of its divisions all over the country Attendance report daily/monthly and attendance log report,attendance statistics report Real time monitoring, it can monitor multiple devices up to a hundred devices at the same time (optional) Upload registered fingerprint data to multiple devices at the same time General features: Size: 165 x 150 x 50mm Colors: black or silver Double CPU, V10.0 4 Korean core learning algorithms + powerful self-owned SW Matching mode: 1: N Response time: 1.1s full of 3,000 Response time: 1.1s full of 3,000 FAR (false acceptance rate): 0.0001% FRR (false rejection rate): 0.01% Temperature range: -10 to +65C Humidity: 15% to 80% Working mode: offline (standalone) LCD language/hint voice: Chinese, English, French, Spanish, Arabic, Japanese Remote real-time monitor or sending-additional charge. Packing detail: 8pcs/carton Carton size: 51 x 41 x 50cm N.W./G.W.: 10.5/11.5kg.
Composite algorithm system with high speed operating Embedded LINUX system, easy to integrate into various system Standalone or network environment Professional access control system support real-time entrance logs transferring 24 hours continuous operation available Saves data during power outage With strong seal appearance, anti-dust. Specifications: LCD display:4 lines character white LCD128*64 Speaker: NO Voice Prompt Fingerprint capacity: 1500 templates Log capacity: 50 000records Verification speed(1:1)í_0.5s Identification speed(1:N) í_1s FRR í_0.01% FARí_0.0001% Communication:TCP/IP,RS232/485,Wiegand out Attendance Status: Check in ,Check out Language :multi language, English, French, Spanish, Arabic, etc,for more than 15 languages can be selected Operation temperature:0 C degrees to 45 C degrees Operation humidity:20%~80% Power :110/220VAC~12VDC Machine Size: 210(L)*95.5(W)*46.5(H)mm Function support : T9 input ,multiple alarm Access control: Built-in relay, with simple access control Customize function : fingerprint capacity enlargement, 9PIN user ID, auto status. Machine Size: 210(L)*95.5(W)*46.5(H)mm.
Composite algorithm system with high speed operating Embedded LINUX system , easy to integrate into various system Standalone or network environment Embedded multi-languages interface Saves data during power outage Support key button tone and various internal bell ring. Specifications: LCD Display : 4 lines character white LCD 128*64 Speaker : Voice Prompt(language can be selected) Fingerprint capacity: 2200 templates Log capacity :50 000 records Verification speed (1:1)í_0.5s Identification speed(1:N) í_1s FRR í_ 0.01% FAR í_0.0001% Communication : TCP/IP,RS232/485,USB Host/Client Attendance status: check in ,check out Language: multi language,English,French,Spanish,Arabic,etc,for more than 15 languages can be selected Operation temperature: 0~45 C degrees Operation humidity:20%~80% Power : 110/220VAC~5VDC Machine size: 194(L)*145(W)*49(H)mm Function support: work code, scheduled bell, websever,log query,T9 input ,USB,SMS Customize function: fingerprint capacity enlargement, printer support,9PIN user ID, auto status. Machine size: 194(L)*145(W)*49(H)mm.
Composite algorithm system with high speed operating Embedded LINUX system, easy to integrate into various system Standalone or network environment Professional access control system support real-time entrance logs transferring 24 hours continuous operation available Saves data during power outage With strong seal appearance, anti-dust. Specifications: LCD display:4 lines character white LCD128*64 Speaker: Voice Prompt(language can be selected) Fingerprint capacity:2000 templates Log capacity: 50 000records Verification speed(1:1)í_0.5s Identification speed(1:N) í_1s FRR í_0.01% FARí_0.0001% Communication:TCP/IP,RS232/485,USB host/client,Wiegand in /out Attendance Status: Check in ,Check out Language :multi language, English, French, Spanish, Arabic, etc, for more than 15 languages can be selected Operation temperature:0 C degrees to 45 C degrees Operation humidity:20%~80% Power :110/220VAC~12VDC Machine Size: 210(L)*95.5(W)*46.5(H)mm Function support : Scheduled bell,T9 input , USB,Anti-pass back, multiple alarm, Web server, SMS Access control: Built-in relay, with 50time zones ,5 groups and 10 combinations Customize function :fingerprint capacity enlargement, 9PIN user ID, auto status. Machine Size: 210(L)*95.5(W)*46.5(H)mm.
Verification Method: Fingerprint, ID+ password, Fingerprint/ (ID+ password) Verification Modeú¦1:1 (500/1500 templates), 1: N (Less than 500 /1500 templates) Verification timeú¦Less than 2.0 sec False Rejection Rate(FRR)ú¦Less than 1% False Acceptance Rate(FAR)ú¦Less than 0.001% Capacityú¦500 templates/1500 templates Powerú¦DC 9-24 V 1A Relay output: 12V, 3A Communicationú¦RS-232/485, TCP/IP Weigand 26 bit Input Communication Speedú¦115200/38400/19200/9600 BPS ú+ TCP/IPú¦10/100M/Auto Log Dataú¦ 30000/100000 events Sizeú¦82*55*180 mm
1. Can save more than 1000 fingerprint templates. 2. The verifying time is less than 1 second 3. Control single door, with mini switch power inside, easy to install and use 4. Support network function, can be managed by computer. Electric parameters: Input voltage: 9vdc~15vdc Operating current: 200ma Max output power: 12w Operating temperature:-20~55 degree Operating humidity:
Access control system Function description : long-range reader 12-15v single power supply; Support weigand26, rs485, aba, rs485interface Features: designed wholly by independent intellectual property rights; high performance; support id card; maximum effective distance up to 100cm and its contour can be specially made by client's requirement.
