Wood sawdust dryer / wood chips dryer General instruction of wood sawdust dryer: 1. Rotary drum type dryer, there are 31 pipes in it, hot air enter pipes directly. 2. Hot air in pipes, biomass materials outside, so biomass materials can avoide be ignited. 3. Indirect heating source prevent raw materials polluted by smoke and dust. 4. Specail desing can make hot air circulate in rotary drum body, and shorted drying time. 5.Brick heaint stove, there are three walls in it with differetn funcationsl, specical structure can prevent smoke, flame and dust enter pipes, just enter clean hot air. 6heating source can be coal, charcoal, wood, gas, oil, wind power etc. Characters of wood sawdust dryer: 1is mainly to dry biomass or fertilizer powder materials , at max feed 15mm dimension materials, it has changeable speed rotary drum , which can dry high humidity materials, such as to dry biomass from sawdust, straw, stalk, e.C.T and fertilizer materials from poultry manure , home or Factory waste 2.Machine dryer drum rpm can be controlled according to raw materials humidity. If humidity is large, then can control feeding speed and drum rpm lower to make longer drying time. The longer drum ensure high heat use efficiency. 3. Has temperature adjusting equipment between stove and dryer, which can adjust the hot air temperature before feeding to drum according to raw materials humidity , after adjusting, then feed to dryer drum 4. Rotaryd drying machine has two ways to discharge materials, One is to outlet from rotary drum bottom, it is mainly fit for large weight ratio materials
Biomass wood sawdust pellet mill is designed specially for the raw material which are hard to press and hard to shape. Biomass wood sawdust pellet mill can press wood, wood chips, sawdust, straw, stalk, shell, rice husk, sunflower seed, peanut shell into good pellets with 1.1-1.4 g/cm3 density. Biomass wood sawdust pellet mill is an ideal optiona for pellet making business, it can deal with most raw material, such as agro-waste, agriculture waste, fruit shell, rank grass and any other wood waste. Biomass wood sawdust pellet mill have double layer die which lengthen the lifetime of the die a lot. It has advantages of flat die pellet mill and ring die pellet mill. They are the best choice for pellet mills for fuel pellets. Seven characteristics of the biomass wood sawdust pellet mill: 1) vertical feeding directly in place. 2) die static, roller rotating, materials centrifugal, evenly distributed around. 3) double layer dies, up and down dual use, reduce the cost, enhance the efficiency, can be dual use. 4) one die, different hole diameters, with different specifications to pelleti. 5) macroporous die, wire joining circular tube, increasing travel, improving density. 6) ring die, vertical structure, good for cooling the pelletizing room. 7) independent and frequebct conversion discharge device, to ensure that the rate of pellet production. Four differences 1) upward mould, special structure, vertically feeding and easier heat disspassion. 2) die static, roller rotating, material centrifugal and distribute around evenly. 3) double layer die, multi function, high efficiency. 4) macroporous die, wire joining circlar tube, increasing travel, improving density.
ModelDie diameterPower(KW)Size(mm)Weight(t) SKJ1051053600*450*9000.12 SKJ1201203600*450*9000.15 SKJ1501507.5750*450*8700.16 SKJ1601607.5750*450*8700.16 SKJ200200111150*530*7500.25 SKJ250250151250*600*8500.3 SKJ260260151250*600*8500.3 SKJ280280221600*600*12000.6 SKJ30030030/221600*560*14000.662 SKJ32032030/221630*590*10600.745 SKJ350350371900*850*17502.2 SKJ360360371900*850*17502.2 SKJ450450451450*700*14501.36 SKJ460460451450*700*14501.36 SKJ550550902600*1100*21003.2 SKJ560560902600*1100*21003.2 SKJ800800130-1603200*1235*27006.8 SKJ10001000130-1603200*1235*27006.8 ModelDie diameterPower(KW)Size(mm)Weight(t) SKJ1051053600*450*9000.12 SKJ1201203600*450*9000.15 SKJ1501507.5750*450*8700.16 SKJ1601607.5750*450*8700.16 SKJ200200111150*530*7500.25 SKJ250250151250*600*8500.3 SKJ260260151250*600*8500.3 SKJ280280221600*600*12000.6 SKJ30030030/221600*560*14000.662 SKJ32032030/221630*590*10600.745 SKJ350350371900*850*17502.2 SKJ360360371900*850*17502.2 SKJ450450451450*700*14501.36 SKJ460460451450*700*14501.36 SKJ550550902600*1100*21003.2 SKJ560560902600*1100*21003.2 SKJ800800130-1603200*1235*27006.8 SKJ10001000130-1603200*1235*27006.8
Model MHB1525A Table size LxW 760x850mm Max working size LxWxH 2500x150x80mm Min working size LxWxH 2000x30x15mm Shaper spindle diameter 70mm Shaper blade diameter Main saw blade size 355mm Shaper spindle speed 6000rpm Main saw spindle speed 3700rpm Working air pressure 0.5 0.8Mpa Max jointing force 7800kg Total power 6.7kw
Model MXB3515T(with glue function) Table size 760x850mm Max working thickness 150mm Max working width 600mm Main saw spindle diameter 30mm Shaper spindle diameter 70mm Main saw spindle speed 2840 rpm Shaper spindle speed 6000rpm Shaper spindle power 11kw Main saw spindle power 4kw Butting saw power 2x0.75kw Total power 16.5kw Overall dimensions 2700x1730x1550mm Net weight About 2000kg
Wood chip crushers are commonly used shredding equipment for processing sawdust of different finenesses. The wood chip crusher can quickly wood , bark,branches,leaves,thatch,bamboos, straws, and other biomass materials into sawdust, and the production efficiency is very high. This industrial machine shredder is a new type of superfine wood processing equipment. Wood chip crusher machine also can be called wood shredder, wood grinder, bamboo mill(milling machine), branches pulverizer. The processing size of the raw materials for the high-efficient wood crusher ranges from 1cm to 20cm, and the final sawdust size can be decided according to the customer's requirements.
1. Application Wood chip Crushers are commonly used as shredding equipment for processing sawdust of different finenesses. The Wood chip crusher can quickly wood, bark, branches, leaves, thatch, bamboos, straws, and other biomass materials into sawdust, and the production efficiency is very high. This industrial machine shredder is a new type of superfine wood processing equipment. Wood chip crusher machines also can be called wood shredder, wood grinder, bamboo mill(milling machine), branches pulverizer. The processing size of the raw materials for the high-efficient wood crusher ranges from 1cm to 20cm, and the final sawdust size can be decided according to the customer's requirements. 2.The basic structure 1.Feed inlet 2.Machine cavity 3.Discharge outlet 4.Mainshaft bearing 5.Machine cavity 6.Machine chassis 7.Copper wire motor8.Pulley guard 9.strainer mesh(3-30mm) 3.OPERATING PRINCIPLE With a fineness analyzer, this wood shredder machine is specialized in crushing lightweight materials, fiber materials, brittle materials, ductile materials, and other special materials. This sawdust-making machine can crush the branches with a diameter of less than 20cm. The main parts of the wood crusher include the feed port, main body, outlet, motor, and holder. As for the main body, there are knife plates, hammers and screen meshes inside. And the quantity of the knife plates and hammers varies according to the model of the wood crushing machine. Generally, the diameter of the holes in the screen mesh is 8mm, but we can also customize the screen mesh for customers' special requirements. The larger the diameter of the mesh holes, the greater the discharging speed and the output of the crushed materials.
Model: MF09 Min diameter of Arc band;40mm Feeding speed 0.5-5.3m/min Tape thickness 0.3-3.0mm Working temperature 120-150 Degree Total power: 765W Glue pot measurement 270ML Net/Gross weight 9.5/14kgs Packing size: 465*430*515mm
-> Speed Conveyors are controlled wood Carrier (size 130 x 60 cm) Fhgkkx9sw -> Adjustable Height Blade (the desired wood shaving thickness can be adjusted) -> Wood Carrier is Konvi Speed Controls (wood shaving Size is set at the desired figure) -> Machinery Spare Parts is our standard production can be obtained from anywhere. -> blower fan -> Can be used for horse or chicken. Technicial Specifications Model : 4 YT - 60 Number of Rollers : 4 Blade Length : 60 cm Number of Blades : 7 x 4 = 28 Motor Powers : 4 * 7,5 KW = 30 KW - Total Engine Power : 33 KW Cutting Setting : 0.5 mm - 2 mm Machine Weight : 2400 KG Production Capacity : 900-1250 kg / h 380V- 50 HZ
Product Introduction The sawdust dryer is used for pellet sawdust or powder sawdust. Wet materials are continuously sent into drum through screw conveyer and then get separated and pushed by high-speed hot flow. The moisture in wet materials is taken away in this process and then we get powder or pellet dry materials. Product Application Sawdust dryer are widely used for the drying of straw briquette, charcoal, wood pellet fuel, sawdust briquette, corn straw, soybean straw, cotton stalk, wheat straw, sorghum stalk, wood shavings, sawdust, gingko leaf, mulberry leaves and other fiber materials. Product Configuration Sawdust dryers are consist of heating furnace, feeding port, drum, filter drum, conveying pipe, cooling drum and discharging port.
The sawdust dryer is used for pellet sawdust or powder sawdust. Wet materials are continuously sent into drum through screw conveyer and then get separated and pushed by high-speed hot flow. The moisture in wet materials is taken away in this process and then we get powder or pellet dry materials. Sawdust dryer are widely used for the drying of straw briquette, charcoal, wood pellet fuel, sawdust briquette, corn straw, soybean straw, cotton stalk, wheat straw, sorghum stalk, wood shavings, sawdust, gingko leaf, mulberry leaves and other fiber materials.
Ring die pellet mills are widely used in the granulation of wood, straw, and other biomass sources. Driven by heavy-duty gearbox construction, it can work continuously in even most adverse conditions. The imported key elements are of high performance with long life and low maintenance cost. The key parts of the ring die pellet mill are made of alloyed steel that is very strong and malleable. Ring die pellet mills die is made of stainless steel. Our ring dies pellet mills capacity ranges are from 200kgs to10T per hour.
Wood Shaving Machine is used to crush wood into shavings and sawdust and is chosen by wood recycling companies and racecourses, good for horse bedding and animal bedding. Also with baler. UK ENERPAT Wood shaving machine is designed to produce wood shavings in desired and suitable size to be able to use them as bedding at chicken farming and horse breeding sectors. There are all adjustment possibilities to get wood shavings in desired size and high quality. Quality Features Automatic running from start to ending Contain-usrunning Preventivesystem for wood jamming Shaving depthcan be adjusted Two motordrive UK safety standard Application Fire wood Logs Timber Scrap wood Scrap furniture Specifications: Model: EWS-37 Motor power: 37KW Max lenght of wood: 140cm Max diameter of wood: 45cm Cutting head: 4sets Blade: 24sets Machine size: 4750 x 1000 x 1800mm Machine weight: 2.8T
This wood sawdust machine is designed to produce wood sawdust in desired and suitable size to be able to use them as many applications .wood sawdust can be used to do the mechanism of charcoal, mushroom cultivation, blackfungus mushroom cultivation, mushroom processing Agaricus bisporus, MDF processing, particleboard processing,fiberboard processing, Zen Incense and mosquito coils manufacturing, paper pulp raw materials, making charcoal fueland other functions. The enerpat ESM-55 automatic wood sawdust machine is one 55kw drive machine,used for making wood from firewood,wood logs and scrap wood .our wood sawdust machine come with automatic re-set function,when feeding thebig size wood into the machine,which can not process,the re-set function will protect the machine and feed back thewood. This sawdust production machine is very specially producing the sawdust from woodlog to sawdust just in one stepwithout hammer mill and grinder process only just one chop-mill. Chop mill producing particle size is 2- 4mm or clientdemanding size maximum 10mm. Lots of European wood pellet producer is changing and using the there wood pelletprocess instead of hammer mill process. It's simple and easy operating and drum knife repairing quiclky also thischop-mill knife life time are 1000Hours production available by normal stone shaving grinder. Chop-mill(sawdustmachine)beaver production capacity is from 25m3/h to 75m3/h range depend on your demading capacity.
Max. working length 1400mm Working diameter range 22~500mm Max. working speed 90-120m/min Veneer thickness 0.5~7mm Double rollers motor power 7.5kw x 2sets Single roller motor power 7.5kw x 2sets Screw Feeding motor power 11kw Rotary clipper motor power 2.2kw Rubber belt conveyor motor 2.2kw Machine size 4700x1900x1500mm Machine weight 7000kgs Total power 45.4kw Remark Including 6 meter veneer conveyor
1. The main structure is strong with enough rigidity and high stability. 2. High efficiency, one shift working can produce 4000(16mm) sheets. 3. High precision anti-wearing guide rail, diagonal error
Technical Parameters: Model Single/Double side glude spreader Roller Dia customized Roller length 2500MM Linear speed 20-50M/min Total Power 7.5 KW Weight 2200kgs Dimension 3400*1750*1900MM Usage: 3 Roller and 4 roller glue spreader are avaliable Single side and double side, 4 Ft and 8 Ft Glue spreader is mainly used in multi layer board, veneer, block noard and so on. The machine has resonable design, can save production cost and is easy to operate.
1.Technical Parameters: Model RBD1400 Max dia of log 500MM Max length of log 1400MM Linear speed 45M/min Total Power 19 KW Weight 3200kgs Dimension 3600*2100*1600MM 2.Features: 1.Log rounding debarker is used for peeling off the log skin and make the raw log to be round, after debarking it will be easy for the peeling lathes to peel and the veneer thickness will be even without big variation. 2. It also can increase the peeling lathes working life. 3.One set debarker can work with two sets of peeling lathes, it can save labor.
1. Product Features: 1.Used for poplar core veneer peelig and cutting. 2.Veneer thickness is adjustable, double sides smooth. 3. Peeling speed is adjustable. 4.High/Normal speed avaliable, double power. 2. Technical Parameters: Max Wood dia: 500mm Max length of Log: 1400mm Dia of left wood: 26mm Veneer thickness range: 0.5-7mm Peeling Speed: 55- 100M/MIN avaliable Total Power: 41.4kw Overall dimension: 4900X2000X1550mm Total Weight: 7000kg
1.Product Description: 1.This machine is used to peel log without skin to core veneer and continue peeling log core after spindle peeling. It is very popular for plywood industry. 2. CNC Spindle less Veneer Peeling Lathe, with hydraulic system for knife installation which makes easy to change knife when need to grind and save time. 3. Servo motor, Precision hardened gear reducer. 4. Japanese Mitsubishi CNC system . 5. We have 4f, 6f and 8f to meet different requirement. You can choose it according to your demand.
