Wooden toothpick making machine.
Planer Plate dimensions400 x 2300 mm Front plate length 1110 mm Rear license plate size 1110 mm Max. Planing length 18 mm Trench slope angle0-45 Blade qty 4 Top spindle speed 4000 rev / min Top shaft diameter 105 mm Saw tray Plate dimensions 550 x 800 mm Circular saw blade diameter 350-400 mm Shaft diameter 30 mm Tray spindle speed 3600 Drill Plate dimensions 270 x 480 mm Longitudinal motion 170 mm Transversely action 135 mm Vertical movement 160 mm Drill diameter 20 mm Machine Motor force 4 hp Dead weight 850 kg.
FrameCut from the whole steel plate Cylinder diameter220mm Cylinder structureSolid Cylinder stoker200mm Hydraulic systemTaiwan HeatingElectric heating, nano technology Vacuum pumpImport.
Outer size (length*width*height): 9930mm*2230mm*2150mm Inner size: 2550mm*1270mm Weight: 10t Maximum working height: 50mm General power: 46.5kw. Outer size (length*width*height): 9930mm*2230mm*2150mm Inner size: 2550mm*1270mm Weight: 10t
High frequency vacuum dryer is smaller type fast dryer, suitable for hard or thick wood drying, it is a best choice for hard wood furniture company. High frequency dryer applies both high frequency and vacuum condition. 1.Character: High frequency heating: high frequency power acts only on the moisture of the wood, it penetrates the wood and where there is water or moisture, there is high frequency power. So it dries: fast and uniform Vacuum condition: At vacuum condition, the water is vapor at very low temperature, so this eliminate the problem of sparking or splitting problem for hard wood, especially for the type of extremely hard wood that likely to spark if drying temperature is too high. Further more , vacuum condition create a minus pressure in the tank, this minus pressure suck the water or moisture out of the wood fast 2 sagas high frequency dryer is plc automatically controlled , high frequency and vacuum pump is start and puse automatically during drying, water come out of the wood is automatically released by water control system to a water holding tank. Weight calculating system get the data of weight change of the wood, by this, the moisture content with-in the wood is readable. Very precise fiber glass(optical fiber) temperature sensor make sure the wood drying at right temperature to eliminate any chance of split or spark on the wood. Plastic and foam, seaworthy package Dimensions of tank: 1300mm Gross weight:9400kgs
Danyang dingjian tools co., ltd. Was founded in 1991 and is located in danyang city, one of the biggest manufacturing base for cutting tools in china. As a leading professional cutting tools supplier in china, our main products include drill bits, saw blades, hole saws, tool bits, screws, shovel, wrench, reamers and other cutting tools, We has a batch of skilled workers, experienced technicians and senior engineers. We also introduce advanced automatic equipment for research, development and manufacture. Meanwhile, we are punctilious in pursuit of raw materials, process of manufacture and test of quality, trying our best to reduce the cost and supply customers with high-quality products at low prices. We have been supplying quality tools and accessories for trading and construction companies for years. There is no service we do not bend our backs to perform. We have created a reputation in our field as a company which can compete in quality, price along with timely delivery. For the last we know the needs of our customers and therefore work hard to fulfill their requirement and to see that they are satisfied. It is our firm belief for our customers that we cannot spell s_ccess without "u".
Dcx 2000 series computerized frame paperboard cutting machine Max cutting speed 600mm/s Max moving speed 4500mm/s Max cutting thickness 3mm Cutting angle 45/55 Effective cutting range 1200*800mm Resolution ratio
Feature: 1.Blade up & down movement by electric control. 2. digital display for saw blade inclination angle(0-45 degree). 3. wide duralumin sliding table. 4. high precision steel guide. Main technical parameter for MJ61-32TAS. Dimension of sliding table3200x435mm Gross cut capacity 3200mm Width of cut between saw blade and rip fence 1250mm Saw blade diameter 300mm(250-450mm) Height of cut (300mm) 80mm Speed of main saw spindle 4500/6000rpm Main spindle diameter 30mm Tilting saw blade 0-45-90° Main motor 5.5kw 380V , 50HZ, three phases Scoring saw blade diameter 120mm Speed of scoring saw blade 8000rpm Scoring saw diameter 20mm Scoring motor 1.1kw weight 950kgs Overall dimension 3200x2450x900mm.
Profile : E4E,T&G 2 side, reeded , groove and double profile Conditions : KD MC 12 - 20% Cutting : Quarter sawn and semi quarter sawn. Standart ISPM #13 KD processing and S4S Size : 100 x 1050 x length wood size 110 x 1200 x length wood size buyers order.
Profile : T&G 2 side, E2E, E4E and reeded KD MC 12 - 16% Cutting : Quarter sawn and semi Quarter sawn colour : uniform colour or semi unform colour Unfinish. Standard ESPM #13 KD processing and S4S size : buyer order.
Max. drilling diameter : 35mm Max. drilling depth : H max=60mm Max. processing pitch: 1300x672mm Min.processing pitch: 130x32mm Total number of drilling shafts: 63 pcs Total number of drilling rows: 21x3 rows Installing dia to the drill: 10mm Distance between spindle: 1300mm Working pressure: 0.5~0.6Mpa Total power of motor: 4.5kw Spindle speed: 2840rpm Exterior of machine: 2200x2500x1600mm Weight of machine: 1400 kgs. Packing: wooden case.
1, Using four-edge knife, easy to use and low cost. 2, Knife plate voltage controlled by the hydraulic control, advanced structure, reliable performance. 3, Feed part adopt stepless speed .It has good peeling effect on the cold wood, curved wood, eucalyptus, oak, elm and other tree species has a good hard. 4, Peeling the net high, high productivity, little injury for the wood. Model (slwd)150220260300 Max diameter150mm 220mm 260mm 300mm Knife quantity 4 4 4 4 Main power 4.0kw4.0 kw5.5 kw 5.5 kw Driving power 1.5 kw1.5 kw1.5 kw1.5 kw. Wooden case.
1, Whole machine welded with seamless steel structure which is stable and durable. 2, There axises of X,Y and Z equip dust cleaner system to prolong life-time. 3, Workpieces can be placed at the stop. 4, It is compatible with the process codes of multiple national and international software. Technical data: Machine size : 1440*3040mm Work envelope : 1300*2500mm Respositioning resolution : 0.05mm Resolution : 0.025mm Power of spindle : 4.5kw Spindle speed : 1-1800(2400)rpm Power of horizontal spindle : 6kw Rotate speed of horizontal spindle : 1-1800rmp Max.speed : 30m/min Max.cutting speed : 15m/min Bridge clearance : 200mm Working voltage : AC380v/50HZ Command code : HPGL,Gcode.
Motor 2.2kw Saw Wheel Diameter Ø600mm Saw Blade Speed 10 m/s Max Cutting Depth 260mm Speed of saw wheel 900r/min Table Size 695*610mm N.G.Weight(kgs) 210kgs Table Tilt 0°-45° Overall Size(cm) 1180*720*1850. In wooden box.
Dimensions sliding table: 3200x370mm Cross cut capacity: 3200mm Width of cut between saw blade and rip fence: 1250mm Saw blade Dia.: 300mm(dia.250-dia.350) Height of cut dia.300mm: 70mm Height of cut with saw blade dia.300mm at 45degree: 55mm Speed of main saw blade: 3/4/5000rpm Spindle diameter: 30mm Tiling saw blade: 0-45 degree Main motor: 4kw Scoring saw blade: 120mm Speed of scoring saw blade: 9000rpm Spindle of scoring saw: 20mm Motor: 0.75kw Net weight: 1100kg Gross weight (wooden packing case): 1150kg Overall dimensions: 3180x3200x900mm. In wooden case.
e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips. The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors More information on requests, for spam protection please introduce yourself properly. Technical data: Model: RDY 80-300 Manufacturing year: 1995 Capacity (throughput): 220 m3/h loose wood chips Press roll diameter: 915 mm Roll length: 2440 mm Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz Press distance between the rolls: 2.2 mm Gearboxes: 2 x Kipo Benzler TV 512 Hydraulic pump: Rexroth 200 bar with Mecman syliders Electric motor for hydraulic pump: ASEA 7.5 kW Weight: 33 000 kg Length: 5083 mm Width: 2550 mm Height: 2400 mm.
Technical Specifications : Exterior size: 5800(Double plate 8800) mm, 1500 mm, 1400mm Working plate inner size: 2550mm, 1150 1300 mm (if producing the door, you choose 1150mm;if producing cabinet, you choose 1300mm) Maximum height of the work piece:50mmincluding height of Magnetic block or bottom plate Rating working pressure: -0.095Mpa General Power: 15kw Actual power consumption: about 5kw Weight: 2.5T Top temperature:180. EPE film+preservative film 3.2X1.8X2M 2500KG.
Technical Specifications : Exterior size :10030mm, 2230 mm, 2150mm Working plate size:2580mm, 1270mm inner size Suitable for cabinet, the width of PVC film should be 1400mm Maximum height of the work piece :50mm including bottom plate Rating working pressure: Positive pressure 0.6Mpa Negative pressure : -0.095Mpa General Power: 65kw Actual power consumption : About 15kw Weight :12.6T Top temperature:150 EPE film+preservative film, 3.25x2.25x2.05m+2.3x1.25x1.8m 12000kg.
MHS1560*600 Technicial Specifications: Characteristics: Comb tenoning and splicing is an effective way to connect the timbers to a longer length, is able to increase the utility rate of shorter timbers and reduce resources waste. The automatic finger-joint production line features compact structure, rational arrangement, high precision and efficiency, and manpower saving, is widely used timbers processing industry. Model MXZ3515T Auto Finger Shaper (Include Glue Spreading) MXZ3515 Auto Finger Shaper MHZ1560 Auto Finger Joint Assembler Table size (W*L) 850*600mm 850*600mm ---- Max. working size (L*W*H) 850*80*150 850*80*150mm 6200*150*80mm Min. working size (L*W*H ) 200*30*20mm 200*30*20mm 1000*30*20mm Shaper spindle diameter 70 mm 70 mm ---- Shaper blade diameter 160 mm 160 mm ---- Main saw blade size 255 mm 255 mm 355 mm Shaper spindle speed 5000 rpm 5000 rpm ---- Main saw spindle speed 2840 rpm 2840 rpm 3700 rpm Spreader roller speed 58 rpm ---- ---- Total motor power 17.24 kw 16.12 kw 7.7 kw Working air pressure 0.8 Mpa 0.8 Mpa 0.8 Mpa Max. jointing force ---- ---- 7800 kg Max. production rate ---- ---- 31 m/min.
MHS1560*600 Technicial Specifications Characteristics: Comb tenoning and splicing is an effective way to connect the timbers to a longer length, is able to increase the utility rate of shorter timbers and reduce resources waste. The automatic finger-joint production line features compact structure, rational arrangement, high precision and efficiency, and manpower saving, is widely used timbers processing industry. Model MXZ3515T: Auto Finger Shaper (Include Glue Spreading) MXZ3515 Auto Finger Shaper MHZ1560 Auto Finger Joint Assembler Table size (W*L) 850*600mm 850*600mm ---- Max. working size (L*W*H) 850*80*150 850*80*150mm 6200*150*80mm Min. working size (L*W*H ) 200*30*20mm 200*30*20mm 1000*30*20mm Shaper spindle diameter 70 mm 70 mm ---- Shaper blade diameter 160 mm 160 mm ---- Main saw blade size 255 mm 255 mm 355 mm Shaper spindle speed 5000 rpm 5000 rpm ---- Main saw spindle speed 2840 rpm 2840 rpm 3700 rpm Spreader roller speed 58 rpm ---- ---- Total motor power 17.24 kw 16.12 kw 7.7 kw Working air pressure 0.8 Mpa 0.8 Mpa 0.8 Mpa Max. jointing force ---- ---- 7800 kg Max. production rate ---- ---- 31 m/min.
