Wire diameter for welded steel bar panels: ranges from 5mm to 12mm Welded bar panels opening: 50mm to 300mm Panel length: 100cm to 1200cm Panel width: 100cm to 300cm
Reinforcing mesh SL82.
Brief Introduction of Wire Mesh Cable Tray Systems: These are thicker and therefore stronger than apparently similar products. Cablofil incorporates a unique T welded safety edge resulting in performance comparable with traditional cable tray but with many added benefits. Features and Benefits of Wire Mesh Cable Trays: 1. Electroplated Zinc Finish 2. Fast Easy Installation 3. Mesh Design Allows Cable Exit or Entry at any point 4. Clear Cable Identification 5. Supplied in 3 Metre Lengths 6. Significant Cost Savings Compared to Standard Tray Products 7. Simple Creation of Fittings on Site 8. Wide Range of Sizes 9. Heights Shown are Internal Dimensions Manufacturing: Optional Material for wire mesh cable tray: Black Steel, Stainless Steel, Aluminium, Alloy, Fibreglass Reinforced Plastic (FRP) Mode: Top curved / Top Straight Surface Finish: Zinc-plating, Hot-dip Galvanizing (HDG), Powder-coated, Pickled & Passivated. Color: Optional Suggestions: 1). MATERIAL The choice of materials is a matter of the physical and mechanical properties produced by each, compared against the intended function, as well as the environment, in which the trays are to be installed. 2). SURFACE FINISH: A). Zinc-plating cable trays are suitable for indoor use. The place where cold zinc-plating cable trays would work should be dry, ventilated, and corrosion free. B). Hot-dip Galvanizing (HDG) cable trays are not suggested for wire mesh cable trays. C). Powder-coated cable trays should be carried out in alkali and salt corrosion free site. D). Pickled & Passivated should be used to stainless steel wire trays. Specification for power and communications cabling containment. 1). SCOPE Steel Wire Cable Tray conforming to the material and performance of this specification. 2). GENERAL A). Cable tray shall be manufactured from steel wires, welded together and bent into final shape prior to surface treatment. B). Surface Treatments: i). Electro zinc plated to BSEN 12329-2000 for interior use (level 2) ii). Hot Dipped Galvanised with between 60 and 80 microns of zinc to BS 729. iii). Stainless Steel AFNOREZ CND 17.2 (AISI 316L) C). Steel Wire Cable Tray Widths & Depths i). Cable Tray dimensions are all internal. ii). Depths of 30mm, 54mm, 80mm, 105mm & 150mm iii). Widths of 50mm, 100mm, 150mm, 200mm, 300mm, 400mm 450mm, 500mm & 600mm for depths of 30mm & 54mm. iv). Widths of 100mm, 150mm, 200mm, 300mm 400mm & 500mm for Depths of 105mm & 150mm All trays are of 3005mm long 3). SPECIFICATION a). Steel Wire Cable Tray will be produced from lateral and longitudinal sidewall steel wires, with minimum diameters of -: 4 mm for trays of widths up to 150mm 4.5 mm for trays of widths of 200mm 5.0 mm for trays of widths of 300mm 6.0 mm for trays of widths of 400mm, 450mm, 500mm and 600mm b). Trays will be manufactured with a longitudinal 'T-welded' safety edge along the top wire of the sidewall (excluding CF3050) c). Trays will be constructed with a 50mm x 100mm mesh configuration. d). All tray fittings (e.g. changes in direction, level and size) shall be constructed on site, to the manufacturers instructions, using side action bolt croppers and fastened using 25mm and 30mm counter clamps with M6 bolts and nuts, all surface treated as the tray. e). Trays will be coupled together using either a fast spring coupler or a 25mm/30mm counter clamp combination with supporting lateral splice plate on trays over 300mm width. The coupling will have the same surface finish as the tray. f). Trays shall be supported at a maximum span of 2.5m by trapeze, wall, floor or channel mounting methods and will not exceed maximum loads as specified by the manufacturer. g). All welds will be manufactured to an average minimum tensile strength of 500Kg per weld. 4. TESTS, CERTIFICATION AND CONFORMITY a). Loading and deflection characteristics of the tray should be tested and the results published in accordance with the European Standard CEI/61537. b). Suitability for the support of Cat6 data cabling should be demonstrated by way of independent test verification. c). Fire test certification should be published in accordance with the E30/E90 standard. d). Electrical continuity across a coupling should be demonstrated by means of a published test method and result. We are able to design styles in various specifications according to the drawings and/or samples by the clients. And we offer fair price, excellent quality, quick delivery, continuous improvement. We own customer satisfaction. You can trust on us that we are the leading manufacturer of cable trays. PSC
1.General introduction of our polyester fabric SHANGHAI SHANGSHAI BOLTING CLOTH MANUFACTURING CO., LTD is a professional manufacturer of all kinds of Screen Printing Mesh, Filter Mesh and Flour Mesh, established in 1997. Our company has 3 factories, the largest one is located in ANPING, HEBEI, is a recommended enterprise of the HEBEI Government. The factory in Hebei covers 119 ACRES (79,373 square meters), the two other factories are located in Shanghai. Mainly Products: Polyester Mesh, Terylene Mesh, Nylon Mesh, Polyamide Mesh, Flour Mesh, Stainless Steel Mesh, Iron Wire Mesh, Filter Mesh, etc. screen printing and filteration related products. 2.Application: 1.Equipments: 300 SWISS SULZER RUTI weaving machines, 5 Benninger high speed warping machines, 2 water washing heat setting machines. The width of weaving machines: 280cm, 330cm, 360cm, 390cm. 2.Exported Countries: America, Germany, Japan, Britain, Italy, Russia, Brazil, Turkey, Argentina, Pakistan, Thailand,etc all over the world. 3.Usage:It is widely used in bolting, filter, textile printed and dyeing, printing plate, electronic printing, ceramics, glass printing,the industries of petroleum, chemical, metallurgy, cement, environmental dedusting and mine. The fabric has been brushed, so it is more flexible and thicker,the dedusting efficiency can reach 99.99%. 3. Features & Advantages 1) Imported weaving and warping machines from Switerland or Italy make sure the high quality products and the production. 2) We produce variouse of polyesters mesh, nylon mesh and some other stainless steel mesh for printing and filtering. Our products are widely applied in high-density printed circuit boards, CDs, keyboard, ceramics, printing of T-shirt textiles, printing on glasses, and adadvertisement signpost making etc.. They also serve as filter in aerospace, petrifaction and other high technology regime 4.Technical specifications Model Specification (/cm) Mesh count (mesh/inch) Thread Diameter (um) Mesh opening(um) Open Area(%) Thickness(um) SS-PET7/1080 7 18 350 1080 57 640 SS-PET8/950 8 20 300 950 58 550 SS-PET10/700 10 25 250 700 49 620 SS-PET12/583 12 30 250 583 49 450 SS-PET16/425 16 40 200 425 46 400 SS-PET20/320 20 50 180 320 41 350 SS-PET24/297 24 60 120 297 51 240 SS-PET29/213 29 76 120 213 41 240 SS-PET32/213 32 80 100 213 46 200 SS-PET34/194 34 86 100 194 44 221 SS-PET36/178 36 90 100 178 41 216 SS-PET40/170 40 100 80 170 46 150 SS-PET43/153 43 110 80 153 43 130 SS-PET47/142 47 120 71 142 44 135 SS-PET53/125 53 135 64 125 44 120 SS-PET59/105 59 150 64 105 39 120 SS-PET62/100 62 155 64 100 37 115 SS-PET64/92 64 163 64 92 35 120 SS-PET68/83 68 173 64 83 32 130 SS-PET72/84 72 183 55 84 37 100 SS-PET77/75 77 195 55 75 33 105 SS-PET90/66 90 230 48 66 35 85 SS-PET100/61 100 250 40 61 37 70 SS-PET110/52 110 280 40 52 33 85 SS-PET120/42 120 300 40 42 26 68 SS-PET140/37 140 350 34 37 24 58 SS-PET150/34 150 380 31 34 26 46 SS-PET165/420 165 420 31 25 17 46 Carton(Customized Received)
Concrete slab mesh is reinforced welded wire mesh panels. This reinforced welded wire mesh panels are made of galvanized welded wire mesh for constructional uses. For example, block slab structure reinforcing, and hollowed slabs reinforcement, building wall reinforcement and support wall reinforcement. It has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction. Variety: truss mesh reinforcement. Ladder mesh reinforcement. Available material: hot dipped galvanized, electro galvanized or stainless steel.
Brick wall reinforcement mesh is welded wire sheet for reinforced concrete construction. It is used in building surface, wall, ground, bridge, bank and airport. And its feature is that welding spots of warp wire and weft wire are on the same surface. Wire diameter: 2.5-6.0 mm Width: 5cm-27cm Length: 3mm. Spacing: 40cm Surface treatment: welded after hot dipped galvanized, welded after electro galvanized, welded before electro galvanized, welded before hot dipped galvanized, welded by stainless steel wire. We have two types of brick wall reinforcement mesh: truss-mesh reinforcement and ladder-mesh reinforcement. Package: carton/pallet/plastic wrapped. Package: carton/pallet/plastic wrapped.
Reinforcement mesh is a welded wire fabric, prefabricated steel reinforcement material. It has a rectangular or square reinforcement mesh grid pattern and is produced in flat sheets. Reinforcement mesh sheets are usually 6m long x 2.4m wide as standard. Concrete reinforcing mesh is superior quality welded wire mesh panels with flat even surface, firm structure. This welded wire mesh panel offers flat even surface and firm structure. It can be used extensively in building, food, agriculture, and serve in construction and fencing applications. We offer three types of concrete reinforcing meshes: welded stainless steel wire mesh panels, galvanized welded mesh panels, and hot-dip zinc plating welded mesh panels. The reinforcing mesh length does not limit. Applications: industrial, manufacturing, guarding, security, enclosures, large animal enclosures, quarantine caging, fencing and gabions.
The longitudinal and transverse reinforcement bars are welded into concrete wire mesh. The concrete meshes have a more dense spacing of the steel bar. Concrete wire mesh is also named welded steel fabric. Application: concrete wire mesh is used for coal mine tunnel network protection or reinforcement, concrete pavement, bridge deck pavement, airport runway, tunnel lining, housing floor, roof, wall, floor, concrete pipes and so on. Advantages: concrete wire mesh for a new, efficient and high-quality steel reinforced concrete structures can be reinforced to reduce the installation of a large number of working hours, less than banding employment nearly approached net 50% - 70%. Concrete wire mesh can help to prevent the emergence of concrete cracks and development, roads, floors, floor welding network configuration can reduce the surface of concrete about 75 percent split.
Continuous high chair with plastic tip provides support for upper slab steel from slab form. It height is from 2" to 15" in 5'-0" lengths. Legs are spaced 7-1/2" on centers. It is available in bright basic, plastic-protected, galvanized, and epoxy-coated and stainless steel. Application: support upper slab steel from slab form surface. They are substitutes for individual chair supports. Continuous high chair upper Continuous high chair upper is used for supporting one layer of steel above another and spacing them to required distance. Standard leg spacing is 7-1/2" on centers. Heights and lengths are same as slab bolsters. It is made in standard 5'-0" lengths. It is available in bright basic, plastic-protected, galvanized, epoxy-coated and stainless steel.
Chain link fence usage: fencing and protection for road, airport, residence district, sport fields, garden, feeding and husbandry. material: low carbon steel wire surface : hot dipped galvanized, pvc coated, galvanized then pvc coated post: square post, round post Product details ¡østandard aperture : 40x40mm, 50x50mm, 60x60mm, 70x70mm, 80x80mm, 100x100mm ¡øwire diameter: 2mm-4mm ¡øfence height : 1000- 3000mm ¡østandard colors are green ral 6005 and black ral 9005, other colors available The design and specification can be made according to customers specific requires Post ItemSizeHeightSurface Square postDiameter: 40mm, 50mm, 60mm Thickness: 1.2-3.0mm1-3.5mGalvanized Pvc coated Round postDiameter:48mm-75mm Thickness: 1.2mm-3.0mm1-3.5mGalvanized Pvc coated No
Plain stainless steel dutch wire mesh Wire diameter from 0.10x0.071mm to 0.036x0.025mm. Other sizes not listed below also available at customers' requirements. For warp-not-fully-covered twill dutch weave, we provide wire mesh made with special twill weaving types, thus to ensure the weft wire distributed smoothly. Packing:inner water-proof paper and plastic paper, six rolls to a carton
Stainless steel woven wire mesh Materials type: stainless steel aisi316l, 316, 304l, 304 and etc. Other material types: copper (brass & bronze), nickel, inconel (incoloy) Monel, titanium, sliver Plain steel, galvanized iron and aluminum Woven type: plain weave, twilled weave, plain dutch weave, twilled dutch weave, reverse plain dutch weave as well as reverse twilled dutch weave and five-heddle. Mesh openings: 0.003 to 10mm (other specifications on request). Wire diameters: 0.010 to 1.20mm (other specifications on request). Width: up to 6mtrs. Appli cations: metal woven wire mesh can have been used widely in various fields such as: oil, chemical, mining industry, food, medicine, machine building, rubber and others. Product feature: we weave mesh with high quality of flat surface, square aperture, accurate filtering rate. In normal export packings with wooden cases outer packings
Decorative mesh is also known as filter cloth or micron cloth. Wire materials: mainly stainless steel wire such as: sus304, sus304l, sus316, sus316l and etc., other material types includes nickel wire and plain steel wire Typical weaving patterns: dutch plain, dutch twilled, dutch reverse. General use: filtering and screening in airspace, oil and chemicals. Normal packing for export of wooden case outer packing
Barzelan manufacturers galvanized steel wire from 1.6mm up to 7.4mm- soft, medium and high carbon wire with light and heavy zinc coatings for a variety of applications such as industrial and domestic products, agriculture, the automotive industry and finished fencing products such as chain link, field link, barbed wire and more. We ship our products worldwide in 20 foot containers by tonage.
Materials: low carbon steel wire, galvanized steel wire or annealed wire. Feature: pvc coated iron wire offers excellent corrosion resistance and anti-aging property and longer service life compared with common galvanized iron wire. Sizes: 0.5-4mm before coating; 1.0-5.0mm with coating layer. Colors available: dark green, black, white, blue, green or other colors. Standard specification: bwg 6#-bwg 32# Application: the most popular use for pvc coated wire is in the construction of chain link fences for industrial security fences, freeways and tennis courts. It is also used in other applications such as coat hangers and handles. Plastic film bag inside , woven bag outside
Materials: low carbon steel wire, stainless steel wire or brass wire. Processing: twisted before galvanized, weaving after galvanized. Electro galvanized, hot dipped, plastic-coated, stainless steel, pvc coated, etc. Weaving type avaliable include: straight twist, reverse twist, double-direction twist. As you require
Processing & features:this kind of galvanized wire is made with choice mild steel, through wire drawing, wire galvanizing and other processes. Electro galvanized iron wire has the characteristics of thick zinc coating, good corrosion resistance, firm zinc coating, etc. 5kg/coil , 10kg/coil, 50kg/coil as your requirments
Features: black annealed wire is rust proof within 6 months without any oil coating. The tensile strength is 300-400 newton per square millimeter. Wire sizes: wire diameter ranges from 0.70mm to 40mm. Forms of supply: straightened cut wire, u type wire, coil wire, etc. Application: black annealed wire is mainly used as industrial wire, construction wire, industrial bale tie wire and constructional tie wire, etc. Packing: different coil diameter or coil weight available for customers¡¯ choice
Material made by standard low carbon steel wire through the process of wire drawing, acid washing, rust removing, annealing and truncation. Wire dia:0.15mm-6mm Application: used for building industry as a binding wire , and all kinds of mesh products and other handicraft. 10kg/roll
Square wire mesh Material:sus 201, sus302, 304, 304l, 316, 316l stainless steel wire, electro galvanize iron wire , hot dipped galvanized iron wire, galvanized drawn iron wire . Weaving: plain weaving Square wire mesh is made with precise struclture and uniform mesh size. It is used in industries and constructions to sieve grain powder , filter liquid and gas , and as safety guards on machinery enclosures.Also for wood strips in making wall and ceiling. According to the demand of customer.
