1. Introduction
Kam Chung joint mixture is widely used for filling gaps and joints of wall tile, floor tile, brick, stone block etc. It has many colors and is good against water, sunlight, and heat, thus no need to worry about aging and weathering problems. Because of so many advantages, this tile grout is highly appreciated and has been applied to many big projects.
2. Application
With so many advantages, Kam Chung joint mixture has been used for filling gaps of indoor and outdoor wall tiles, stone panels, floor tiles, square bricks and plaza stones. It is applicable to most buildings, no matter high rise mansions or special structures like hospitals, stadiums, workshop and plaza. In a word, it is an all-purpose and outstanding filling material for all sorts of tiles.
3. Specifications
Drying time 24 hours
Waterproof Yes
Sunlight proof Yes
Color Selectable
Toxicity None toxic
Non- combustibility Class A
Mixing Ratio
(water : joint mixture) 6.5: 25
Packing 25kg/bag
Validity Period 18 months (in shady and cool place)
Extrusion Ability Not squeezable type (KC-J1), cannot be operated with a glass glue gun
Squeezable type (KC-J2), can be worked with a glass glue gun
4. Advantages
(1). Anti-aging
(2). Waterproof
(3). No peeling off
(4). Easy operation
(5). Non-combustible
(6). Environment-friendly
(7). Applicable to various tiles
(8). No pollution and less garbage
Geotube dewatering units are geo-synthetic containers,, made from high tensile woven polypropylene. Essentially a Geotube unit is a large dewatering bag. The special fabric of Geotube units allows for the retention of consolidated valuable nutrients and the dispersal of clear effluent. The Geotube technology has proven it is effectiveness in providing de-watering and filtration for lagoons, municipal sludge, raw septage as well as a host of other industries around the world since 1982.Mechanical PropertiesTest MethodMinimum Average (English)Minimum Average (Metric)Mass/UnitASTM D-52618.0 oz/yd²271 g/m²Grab Tensile Strength(MD x CD)ASTM D-4632240 x 240 Ibs1068 x 1068 NGrab Tensile ElongationASTM D-463270 x 70 %70 x 70 %Trapezoidal TearASTM D-453390 x 90 Ibs400 x 400 NCBR PunctureASTM D-6241630 Ibs2802 NApparent Opening Size(AOS)ASTM D-475180 US Std.Sieve0.18 mmPermittivityASTM D-44911.5 sec-11.5 sec-1Water Flow RateASTM D-449195 gal/min/ft�²3870 L/min/m�²UV Resistance(% retained after 500 hours)ASTM D-435580 %80 %Advantages of Geotube�® dewatering units:- High volume containment- Opportunity to spread project costs over several years- Rapid flow through rate- Drastic reduction in disposal cost- Lower capital cost- Simplicity
Description
PU-850 is a one component, thixotropic, polyurethane waterproofing membrane where viscosity of the liquid is paramount. In applications such as sloped roofing,
flashing details and under tile waterproofing PU 850 cures to form a durable yet elastic membrane with strong adhesion to many types of substrates. PU 850 is
fast curing, and is tack-free in less than two hours, with exceptional elasticity. Due to it thixotropic, hydrophobic and elastomeric nature, PU 850 is the perfect solution to provide excellent waterproofing on vertical and sloped surfaces without running.
Feature
â?¢ Easily applied onto vertical and sloped surfaces with no running OR bubbling.
â?¢ Excellent adhesion to most substrates.
â?¢ No thinning required.
â?¢ Excellent thermal resistance, never turning soft.
â?¢ Excellent cold resistance, remaining elastic to -40â?°c
â?¢ No accumulation of humidity under coating
â?¢ Excellent mechanical properties
â?¢ Highly stable, will not bleed through porous materials
â?¢ Bitumen free
â?¢ Highly elastic and stable.
Packaging
15 Litre pail
Consumption
1.2~1.5kg/m�²
Shelf Life
Unopened pails can be stored for up to 12 months in
a cool, dry and weatherproof environment.
DESCRIPTION
CA-055(W12) is an emulsion primer of water-based acrylic resin with excellent properties such as water resistance, pull-off strength and pore-filling ability etc. , especially used to improve the physical properties of cement. It can be mixed with water at any ratio.
FEATURES
*Excellent penetration into the concrete substrate to increase pore-filling ability and adhesion.
*Reduced transport paths of concrete structure to enhance durability.
*Excellent water resistance.
AREA OF APPLICATIONS
*Repair mortar for concrete areas.
*Industrial flooring.
*Bonding agent for new to old concrete.
*As cement grout additive.
*As water-based primer.
*For making two component tile adhesives.
*As adhesion aid for skim coat materials.
PACKAGING
20kg Plastic Pails
FLAMMABILITY
Being water-base, it is non-flammable.
CLEAN UP
Tools and equipment can be easily cleaned up with cloth before drying.
1534 Waterproofing Material Suppliers
Short on time? Let Waterproofing Material sellers contact you.
Description
HYPERCOAT-568 is a single-component,high-strength water-based waterproof coating
composed of modified copolymer, which has both waterproof and thermal insulation effects, and has good water resistance and weather resistance.
Use
â?¢ Bathroom, Balcony, Terrace
â?¢ Roof (flat/sloping)
â?¢ Floor seams, parapet
â?¢ Suitable for old and new waterproof engineering made of acrylic or PU material.
Feature
â?¢ Can be used immediately after opening the bucket,easy to use, suitable for DIY users.
â?¢ Good adhesion to cement.
â?¢ Can be directly tiled or exposed directly after drying.
â?¢ Good water and UV resistance, forming excellent weatherability.
â?¢ After completely curing, the water-proof layer of the roof is walkable.
â?¢ Can effectively block heat transmission.
â?¢ Waterproof repair for new and old metal iron roofs.
DESCRIPTION
CP-320 is a fast-curing, two-component, bitumen-extended polyurethane fluid.
It produces a highly elastic membrane with strong adhesion to many types of surfaces and excellent mechanical and chemical resistance properties.
FEATURE
Components easily mixed, fast curing
Its low modulus gives it excellent substrate crack-bridging properties
Excellent adhesion on almost any surface
Excellent thermal resistance, max service temperature 80
Resistance in the cold: Film remains elastic even down to -40
Good chemical resistance
Can also be used as a joint sealant
APPLICATIONS
Bathrooms, balconies, basements and rooftop
Gypsum and cement boards
Light roofing made of metal or fibrous cement
Non-potable water tanks
Bridge platforms
Cut-and-cover tunnels
Irrigation channels
Commitment To Quality
Provide good quality and reliable premixed product
Consistent customer satisfaction
Continual improvement through the effective quality management system
QMS compliance with national and international standards
Sales & quality engineers will provide with timely and prompt delivery
Client Satisfaction
Customer satisfaction has always been the major objective of our company. To achieve this objective, we always fulfill the demands of our clients. We also provide customized solutions in the designing of our products according to the customer's requirements. Flawless products are provided to our clients at an affordable prices. Due to our wide distributing network facilities, we deliver the products to the clients on time. We also follow different kinds of payment mode that helps the clients to pay easily. In order to deliver a quality assured product, we procure the ingredients from the reliable vendors of the market.
DESCRIPTION
CA-002W(12) is an Acrylic Polymer emulsion, especially used to improve the physical properties of cement. After mixing grout with CA-002W(12) can increase water resistance and bonding strength.
AREA OF APPLICATIONS
* Repair Mortar for Concrete Areas
* Industrial Flooring
* Bonding Agent for New to Old Concrete
* As Cement Grout Additive
* Enhance adhesion strength of Mortar.
PACKING & STORAGE
20kg per plastic pail.
Please store in cool places and avoid direct sunlight.
DESCRIPTION
CC-103(1K) Crystalline Waterproofing Materials is fusion resin powders which contains water-soluble crystalline mineral coating with special additive syntheses. It will have a protective coating which is firm and impact resistance after curing. CC-103(1K) is a high technology product to prevent water leakage.
ADVANTAGES
* Prevent the constructions aging phenomenon
* Avoid the leakage and mold on the wall
* Effective against negative water pressure
* With good stability
* Non-Toxic
APPLICATION
* Internal and external walls
* The leakage of inner wall in basements or the protection against negative water
pressure
* The construction of base isolated structures
* Reservoir; drinking water pool
* Contaminated water pool; water storage tank
PROCEDURE
1. Ensure all surfaces which CC-103(1K) will be applied are clear.
2. Mix one pail(22.5KG) of CC-103(1K) and 4.5~5.0Liter water well by construction mixer.
3. Wait for 3-5 minutes and stir before use; use finishing trowel to smoothing or apply
evenly with a nap roller.
4. Use finishing trowel to smoothing after using spray machine.
PACKING
22.5KG per pail.
STORAGE
6 months in original container stored in dry conditions.
LIMITATION
The crystalline products need to be used between 4 °C ~ 32 °C when applied.
DESCRIPTION
CP-310 was synthesized from imported high-technology macromolecule resin and
specialized paint that is different from general acrylic resin. CP-310 is a perfect product to
provide a high water-tolerant, climate-tolerant, and anti-UV ability.
FEATURES
* Excellent environmental water-based waterproofing paint
* Water-based, Non-toxic, odorless, inflammable, and harmless
* Fine adhesion, extreme toughness, high elastic, and high endurance
* Hydrophilic, and may be applied on damp surface
USE
RoofBuilding, condominium, factory, barracks, school, garden and etc..
WallsBasement wall , exterior wall , and etcâ?¦
PREPARATION
1. (The following steps are recommended for best results)
2. New concrete must cure for a minimum of 30 days
3. All holes or cracks must be properly patched
4. All surfaces must be clean and free of dirt, dust, efflorescence and oil
APPLICATION
(The following steps are recommended for best results)
1. Stir well before use. Do not thin; however, if thinning is necessary, thin water at a
rate of no more than 10%
2. One prime required CP-310 primer
3. Two coats are required for the best resultskeep the thickness of each coating
below 1m.
4. Wait for each coating to be total dry before overlaying the next coat. The interval
time between each coating is minimum of 8 hours.
COVERAGE
5-gallons about 33m2
COLOR
Grayã??Whiteã??ivoryã??Green
DRY TIME
Dries to touch in about 1-2days . Low temperatures or high humidity conditions will affect
drying time. Full cure should be reached in 14-30 days.
CLEAN UP
1. Clean hands and tools with soap water.
2. After 30 days or paint has fully cured, areas may be wasted using a non-abrasive, mild
detergent and cellulose sponge.
WARNING
(Read the following carefully for your own safety)
1. Keep out of reach of children-Do not take internally.
2. May cause eye, skin and respiratory tract irritation. May be harmful if swallowed. Use
only with adequate ventilation.
DESCRIPTION
CC-103(2K) Crystalline Waterproofing Materials is a capillary waterproofing formulation. CC-103(2K) has high permeability which crystallize and penetrate deeply into the capillaries of the concrete.
ADVANTAGES
* Applied to wet surface
* Transparent, non-toxic and odorless
* High cohesion and effective against positive/negative water pressure well
APPLICATION
* The leakage of inner wall in basements or the protection against positive/negative water
pressure
* Prevent seepage and leakage in underground passages and tunnels
* Avoid the leakage of cisterns and pools
PACKING
30KG/Set
A: 22.5KG in powder.+ B: 7.5KG additive.
COLOR
Grey and white.
STORAGE
6 months in original container stored in dry conditions and under 25°C.
1,Name:construction white or clear leno tarpaulin building cover tarps with words or logo printing
2,Material:100% virgin reinforced HDPE coated with LDPE waterproof lamination with UV stabilizer
3,Color:Transparent / Clear, white, green, etc.
4,Thickness:150 micron, 200 micron
5,Weight:120gsm, 130gsm, 140gsm, 150gsm, 160gsm, 180gsm, 200gsm or customized
6,Features:Anti-UV, anti tearing, anti-aging, anti-hail, etc
7,Light Transmittance �?� 88%
8,Width:1m, 2m, 3m, 4m without jointing, other width has to be welded
9,Length:Any length customized
10,Application:
Fruit trees tent cover (cherry, grape, apple, etc)
Greenhouse roofing cover
poultry house sides rolling curtain
Home garden plant/flower protection plastic film
Construction scafolding cover
Main Features:
1) Anti aging, UV resistant, tear resistant, anti hail, etc
2) Large width provided. 1-4m without jointing,if over 4m, width need to be welded up to 30m
3) No limit on length
4) Customized packing accepted.
5) Free sample available.
PP non woven geotextile fabric
Product Description
PP non woven geotextile fabric is made from polypropylene(PP) short fiber or long fiber by nonwoven needle punched manufacturing process, pp non woven geotextile fabric has isolation, filtration, drainage, reinforcement, protection and maintence etc. function.
APPLICATION :
1.Separation Geotextiles will prevent two soil layers of different particle sizes from mixing with each other , as is illustrated the image below.
2.Drainage Geotextiles will efficiently collect superfluous water from structures , such as rainwater or surplus water, from the soil and discharge it.
3.Filtration Geotextiles are an ideal interface for reverse filtration in the soil adjacent to the geotextile , in all soils water allowa fine particles to moved . Part of these particles will be halted at the filter interface; some willbe halted within the filter itself while the rest will pass into the drain. The complex needlepunched structure of the geotextile enables the retention of fine particles without reducing the permeability of drain.
4.Reinforcement Heavy geotextile can be used to reinforce earth structures by means of fill materials . THanks to their high soil fabric friction coefficient and high tensile strength, they are an ideal reinforcement solution.
5.Protection Geotextile are an ideal protection from erosion of earth embankments by wave action, currents or repeated drawdown. A layer of geotextile can be placed so as prevent leaching of fine material. They can be used for rock beaching or as mattress structure.they can even easily be placed under water.
Product Features
1.High tensile strength and modulus ,low elongation, low creep and high long-term design strength.
2.Ease of Construction.
3.Cost effective.
4.Creep resistance.
5.Consistency.
6.Less differential settlement
Packaging & Shipping
FAQ
1. How about the delivery time?
Lead time since receipt of 30% T/T deposit payment :5-15days?
2. Can you send samples to customers?
Free samples could be provided , but customer need pay for the freigt cost.
3.Can you produce the product according to customers' requirements?
Sure, we are professional manufacturer, OEM and ODM are both welcome.
Why use erosion control matting?
This geotextile is made from, 100% mono filament polypropylene. Mono filament is the superior, erosion controlmaterial with its fishing line-like strands woven together. This provides excellent, stabilisation and reinforcement, for vegetation growth.
Request a price quote
How does a geotextile control erosion?
Geotextiles are, ideal for, soil erosion, prevention, control/repair, and restoration.
The fabric will create a solid base over the eroded soil and, allow the plants to colonize and establish the vegetation, needed to control the erosion.,
, ,
,
Function:
,
1.Geotextile has good air and water permeability to let water flow through it so as to effectively control sandrock running-down.
2.Geotextile has good water transmissibility, it can form drainage channels inside soil mass to drain redundant liquid and air out of the soil mass.
3.Geotextile helps to enhance the soil mass' tensile strength and non-deformability and structural stability so as to improve soil mass quality.
,
Features:
,
1.It can effectively make the concentrated stress diffuse, transfer or decompound, and prevent the soil mass against the destruction of outside force.
2.It can prevent the mixture of sandstone, soil mass and concrete of upper and lower layers.
3.Its mesh is hard to jam by virtue of the compliancy and motility of the reticulation formed by indefinite form fibrous tissue.
4.High water permeability-it can keep good water permeability even in the pressure of soil and water.
5.Corrosion resistant-it is made from polypropylene fiber or terylene or other chemical fiber, featuring resistance to acid and alkali and oxidation, non-corroding, no worm-eaten.
6.Easy construction-low weight, easy operation, simple construction.
Hipped geomembrane for landfill closures waterproof liner 0.1mm-3mm/m2
1. Geomembrane specifications
1) Thickness : 0.15mm - 4.0mm.
2) Width : Within 8 m (1m-8m).
3) Length : 50m-100m/roll (as request).
4) Material : HDPE,( LDPE, LLDPE, PVC, EVA ).
5) Color : Black , white , red , blue , or as required.
6) Optional surface : Textued(one or two side) or smooth surface.
7) Certificate:CE/ISO9001,14001
2. HDPE geomenbrane Features
Good mechanical properties, high tear strength, deformation and adaptable, puncture resistance, anti-aging, anti-ultraviolet-resistant, Anti oil and salt, pH, anti-corrosion, high temperature-resistant, non-toxic, long service life. water, drainage, seepage, the good effect of moisture, width, thickness of the full range of specifications and low cost, simple construction.
3. HDPE Geomembrane Applications
1) Environmental protection, sanitation (such as solid waste landfills, sewage treatment plants, power plants Chi-conditioning, industrial, hospital solid waste, etc.) .
2) Water (such as rivers, lakes and reservoirs of the anti-dam, plugging, reinforcement of the canal seepage, the vertical wall of the heart, slope protection, etc.).
3) Municipal Engineering (subway, on the ground floor of the building, planted roof, the roof garden of anti-seepage, sewage pipes lining, etc.).
4) Landscape (man-made lake, river, reservoir, golf courses reservoirs of the substrate, slope protection, green lawn of the waterproof moisture, etc.).
5) Petrochemical (chemical plants, oil refineries, gas storage tanks of the anti-chemical reaction tanks, sedimentation tanks of the lining, etc.).
6) Mining (washing and pool heap leaching, the ash-field, dissolved, precipitation, the yard, the tailings seepage substrates, etc.)
HDPE geomembrane
NO. Items Value
Common Environment
1 Thickness (mm) 0.2 - 4
2 Width (m) 2.5 - 8
3 Tensile Strength(TD/MD) MPa ?7 ?¥25
4 Elongation at Break(TD/MD) % ?¥4550
5 Strength at Tear(Right-angle Tear) N/m?110
6 Carbon black content % 2.0 - 3.0 2.0 - 3.0
7 Anti-crack F20 ,1500
8 -70low temperature impact brittle prope pass
9 Oxidative Inducement Time at 200°C,m20
LDPE geomembrane
NO. Items Value
1. Thickness (mm) 0.2 - 3
2. Width (m) 2.5 - 9
3. Tensile Strength(TD/MD)MPa14
4. Elongation at Break (TD/MD) 400
5. Strength at Tear(Right-angle Tear)N/m50
6. Permeability coefficient of Vapour(g.cm/cm2.s.p)
Color white or Black
Characters dustproof, waterproof,air permeability,oleophobic
Air Flow 300ml/cm ²/min@70mbar
IP Rate IP67,IP68
ODM,OEM available
Shape round sheet,square sheet,rectangle sheet,customer's design could be available
Structure Adhesive backing or non-adhesive backing
Application sensor,cell,automotive,LED light,power,tester,equipment outdoor electronics etc
Glazed tile roofing roll forming machine main roll forming system:
Usage: in order to keep the product shape and precision, adopts welded sheet structure, motor reducer drive, chain transmission, roller was chromed which can keep the molding plate surface smooth and not easy to be marked when it is being stamped.
Length of the main part: about 650014501500
Weight of main part: 3.8 tons
Voltage: 380v 50hz 3 phase
Roller fixer: middle plate
Frame: 350 h steel welded
Drive mode: chain
Material of rollers:45# steel, surface hard chromium plating.
Material of shafts: 45# steel
Diameter of shafts: ï?80mm
Number of rollers: 13 rollers
Main power: 5.5kw
1534 Waterproofing Material Suppliers
Short on time? Let Waterproofing Material sellers contact you.
