Features: 1. Heavy duty stainless steel construction plus transparent lid 2. 220v/60hz/1ph 3. Lid hold-down device 4. Equip with 6m3/h vacuum pump to have very fast cycle time 5. 20 programs digital control panel with motor over warning, oil change indicated Options: 1. Extra seal bar to have double produce capacity 2. Soft air 3. Gas flushing 4. High pressure seal 5. Top and bottom seal
Valvoline Engine Armour 20W50 Semi Synthetic
Valvoline Hydraullic oil Ultramax-68
Valvoline Diesel Oil 15W40 CH4
Valvoline Diesel Oil 15W40 CI4
Valvoline Engine Oil 20W50 CH4
Valvoline Engine Armour 5W40 Synthetic
SWE-Dubai is the UAE market leader when it comes to Air Compressor and Workshop equipment. We Expertise for the largest sales and service of Workshop Equipment and also have the most comprehensive range of workshop equipment brands and products. Quality New and Used Air Compressors? for Industrial and Commercial Use are Supplied Direct at Dubai.?? Air Compressor: - An air compressor is basically a device that uses a mechanical pump to take air from the atmosphere, compress it and store it. This compressed air can then be used at any desired pressure.Factories and businesses use compressors to drive machinery and air tools. We deal in following types of Air compressors:- 1. Consumer Grade Air Compressors: -Can be described as a pancake or single-stage model. They’re used for household tasks like inflating tires and inflatable products and possibly some low-load air tools like staplers and brad guns. 2. Professional Grade Air compressors: - It provide more power and higher pressurized air. They could be two-stage reciprocating models or rotary screw models and can provide more power to run several air tools at once with intermittent use. 3. Industrial Grade Air Compressors: - It provides more power and higher pressurized air. They could be two-stage reciprocating models or rotary screw models and can provide more power to run several air tools at once with intermittent use. We have solutions for all the needs of Small and Mid-Sized Business for Air Compressors. We also provide Services for the maintenance of Air Compressor and Lubricating Oil for the Compressor Authorized Dealers for: Garage Equipment, Workshop Tools & Machineries, Car Wash System, Industrial Equipment, Fabrication Machineries, Oil Lubricating Equip, Power tools, Hydraulic Equipment, Industrial Air Compressor, Industrial generators. Services &Refabricating:- Hydraulic Equipment, Industrial Air Compressor, Industrial generators, all kinds of Industrial & Lifting Equipment.
Zista group was first established in 2005 as a trading group and during the last decade it has been expanding its network and business through china, hong kong, iran, singapore and several other countries worldwide. Please kindly check our website as below for checking our details and references: Www.Zista.Co We are supplier and provider of all petroleum oils including bitumen, base oil, slack wax, paraffin wax and rubber process oil (rpo). Zista group supply of base oil is direct from iranian refineries and we have been empowered to develop market for iranian base oil in east asia. We are in position to supply different grades of base oil as below: GradesAvailable packaging DrumFlexiBulk Base oil sn 150VV Base oil sn 500VVV Base oil sn 600VV Base oil is a commodity which has worldwide consumption and price reference, depending on international references such as argus & icis for the middle east supply. Zista group is proud to announce its capability to offer fixed & formula prices both for supply of base oil in order for buyers to be able to manage short term and long term contracts, while having an open hand in the available packaging and especially flexi bags, makes it possible to deliver the product anywhere in the world intact and with certified quality. We shall await to receive your genuine inquiry in order to advance to a long term mutual business, Please do not hesitate to contact us for any further discussions, Regards, Alireza rahmani
Please let me introduce our company (emirates rubber products factory/ www.Erpf.Ae) we are a manufacturer of rubber crumb/powder and have the ability to manufacture multiple sizes at large quantities. Our facility is state of the art and is operated by highly trained staff that insure that all our products are of high quality and are free from steel and nylon. We can offer you the best products at competitive rates. Best regards, Mohammed
Specification Value Test Method Penetration @25°C 85-100 ASTM D-5 Specific Gravity @ 25°C 1.01-1.06 ASTM D-70 Softening Point °C 45-52 ASTM D-36 Flash Point °C 225 min ASTM D-92 Ductility @25°C 100 min ASTM D-113 Loss on Heating %wt. 0.5 Max ASTM D-6 Drop in Pen. After Heating % 20 Max ASTM D-6 & D-5 Solubility in TCE %wt. 99.5 min ASTM D-4 Spot Test Negative A.A.S.H.T.O.T 102 Bitumen Penetration Grade 85/100 (also known as 80/100) is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses .
Specification Value Test Method Penetration @25°C 40-50 ASTM D-5 Specific Gravity @25°C 1.01-1.06 ASTM D-70 Softening Point °C 52-60 ASTM D-36 Flash Point °C 250 min ASTM D-92 Ductility @25°C 100 min ASTM D-113 Loss on Heating %wt. 0.2 Max ASTM D-6 Drop in Pen. After Heating % 20 Max ASTM D-6 & D-5 Solubility in TCE %wt. 99.5 min ASTM D-4 Spot Test Negative A.A.S.H.T.O.T 102 Bitumen Penetration Grade 40/50 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses.
Specification Value Test Method Penetration @25°C 60 IS 203 Absolute Viscosity @60°C, Poises 1600-2400 IS 1206 Kinematic Viscosity @60°C, Poises 300 IS 1206 Softening Point °C 45 IS 1205 Flash Point °C 220 IS 1448 Solubility in CS2 %wt. 99.0 IS 1216 Test on residue from rolling thin film oven test Viscosity Ratio @60°C 4 IS 1206 Ductility @25°C 50 IS 1208 VG-20 is usually used for paving in cold climate & high altitude regions
Specification Value Test Method Penetration @25°C 35 IS 203 Absolute Viscosity @60°C, Poises 3200-4800 IS 1206 Kinematic Viscosity @60°C, Poises 400 IS 1206 Softening Point °C 50 IS 1205 Flash Point °C 220 IS 1448 Solubility in CS2 %wt. 99.0 IS 1216 Test on residue from rolling thin film oven test Viscosity Ratio @60°C 4 IS 1206 Ductility @25°C 25 IS 1208 VG-40 is used in highly stressed areas such as intersections, near toll booths and truck parking lots in lieu of old 30/40 Penetration grade. Due to its higher viscosity, stiffer Bitumen mixes can be produced to improve resistance to shoving and other problems associated with higher temperature and heavy traffic loads.
Specification Value Test Method Penetration@25°C 60-70 ASTM D-5 Specific Gravity @25°C 1.01-1.06 ASTM D-70 Softening Point °C 49-56 ASTM D-36 Flash Point °C 250 min ASTM D-92 Ductility @25°C 100 min ASTM D-113 Loss on Heating %wt. 0.2 Max ASTM D-6 Drop in Pen. After Heating % 20 Max ASTM D-6 & D-5 Solubility in TCE %wt. 99.5 min ASTM D-4 Spot Test Negative A.A.S.H.T.O.T 102 Bitumen Penetration Grade 60/70 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses.
Specification Value Test Method Penetration @25°C 90-130 ASTM D-5 Specific Gravity @ 25°C 1.01-1.06 ASTM D-70 Softening Point °C 40-45 ASTM D-36 Flash Point °C 200 min ASTM D-92 Ductility @25°C 100 min ASTM D-113 Loss on Heating %wt. 0.5 Max ASTM D-6 Drop in Pen. After Heating % 20 Max ASTM D-6 & D-5 Solubility in TCE %wt. 99.5 min ASTM D-4 Spot Test Negative A.A.S.H.T.O.T 102 Road Bitumen 90/130 issued for construction and repair of road surfaces, designed for various types of road application such as hot asphalt and bituminous mixtures, recommended for regions with temperate climates
Specification Value Test Method Penetration @25°C 80 IS 203 Absolute Viscosity @60°C, Poises 800-1200 IS 1206 Kinematic Viscosity @60°C, Poises 250 IS 1206 Softening Point °C 40 IS 1205 Flash Point °C 220 IS 1448 Solubility in CS2 %wt. 99.0 IS 1216 Test on residue from rolling thin film oven test Viscosity Ratio @60°C 4 IS 1206 Ductility @25°C 75 IS 1208 VG-10 is widely used in spraying applications such as surface-dressing and paving in very cold climate in lieu of old 85/100 Penetration grade. It is also used to manufacture Bitumen Emulsion and Modified Bitumen products
Specification Value Test Method Penetration @25°C 45 IS 203 Absolute Viscosity @60°C, Poises 2400-3600 IS 1206 Kinematic Viscosity @60°C, Poises 350 IS 1206 Softening Point °C 47 IS 1205 Flash Point °C 220 IS 1448 Solubility in CS2 %wt. 99.0 IS 1216 Test on residue from rolling thin film oven test Viscosity Ratio @60°C 4 IS 1206 Ductility @25°C 40 IS 1208 VG-30 is primarily used to construct extra heavy duty Bitumen pavements that need to endure substantial traffic loads. It can be used in lieu of old 60/70 Penetration grade
Specification Value Test Method Penetration @25°C 10-20 ASTM D-5 Specific Gravity @25°C 1.01-1.06 ASTM D-70 Softening Point °C 85-95 ASTM D-36 Flash Point °C 225 min ASTM D-92 Ductility @25°C 5 min ASTM D-113 Loss on Heating %wt. 0.2 Max ASTM D-6 Drop in Pen. After Heating % 20 Max ASTM D-6 & D-5 Solubility in TCE %wt. 99.5 min ASTM D-4 Spot Test Negative A.A.S.H.T.O.T 102 This grade has a wide variety of industrial applications roof felts. Waterproofing for roof & floors, anti-rust pipe coating, anti-slip layer compound for poling, sound dampening felts, under carriage sealant and coats in the auto motives, electrical cable joint protection and etc.
Specification Value Test Method Penetration @25°C 160-220 ASTM D-5 Specific Gravity @ 25°C 1.01-1.06 ASTM D-70 Softening Point °C 35-43 ASTM D-36 Flash Point °C 250 min ASTM D-92 Ductility @25°C 100 min ASTM D-113 Loss on Heating %wt. 0.2 Max ASTM D-6 Drop in Pen. After Heating % 20 Max ASTM D-6 & D-5 Solubility in TCE %wt. 99.5 min ASTM D-4 Spot Test Negative A.A.S.H.T.O.T 102 Road bitumen 160/220 is a product produced in the process of oxidization of a vacuum residue obtained from the distillation of crude oil. Bitumen 160/220 is used for production of the bitumen emulsions, as a raw material for insulating materials industry, for repairing technologies of damaged road surfaces
