LFG-50 & PT-14 Сable tracing and fault location set, can be used for locating as well as tracing underground metal communications, such as any cables with metal cores as well as metal pipes. In addition, it provides operator with a quick detection of short circuits on cables as well as with an identification of a cable in a bunch. LFG-50 is a 50 W low frequency generator with ability to inject a signal of three frequencies via direct connection to an object or via internal transmission loop antenna, which is built-in a cover lid. Basic frequencies are 491; 982 and 8440 Hz. There are options of using a single-frequency or multi-frequency signals at the output. The power of the low frequency generator LFG-50 output signal can be adjusted up to 50 W with 2.5 W steps. This signal can be transmitted constantly or broken into separate blocks of 50 % duty cycle with 1 s repetition rate. A load matching is made automatically. Main parameters, such as output power, load impedance, selected frequency are shown on OLED display. If a load is higher than 1000 Ω LFG50 automatically switches into output voltage setting mode. The output overload protection will trip, when operating on short-circuit loops (lower than 0.5 Ω). MAIN FEATURES: Portable and lightweight Moistureproof and dustproof case Advanced LiFePO4 internal battery with fast charging option High-contrast graphic OLED display Multifrequency operation Operating frequencies can be changed upon request Internal transmission loop antenna Automatic load impedance matching Ability to work with energized 0.4kV cables (inductive connection) Overload protection Сable locator PT-14 designed for fast and accurate searching for power cables and other communications, identification of coating defects and the depth, followed by mapping.
Wood working industry (converted timber), metallurgy (metal roll), agricultural production, food products, inspection technology, diesel locomotive, wagging spares, chemical production, chemical agents for oil and gas drilling.
Line For Production Of Paper Wipes With Embossed Niagara Digital control. Counting the number of napkins and packs produced on the machine. Resetting this counter is password protected, which allows for independent production accounting. The control panel is equipped with a 17 "monitor and a touch panel for setting the values â??â??of functional parameters, displaying parameters and physical quantities during operation, indication of errors. Smooth speed gain and smooth deceleration is achieved using the STA-C2 frequency converter from NPO Stroytekhavtomatika. Overload protection by current, high pressure, low voltage, overheating, overload, etc. Degree of protection: IP 20.Optical presence sensors allow automatic line shutdown in case of paper break. The unit for forced unwinding and braking of the roll (variator) makes it possible to work with raw materials of any quality (non-uniform structure of the paper web, holes, etc.), including deformed rolls (for example, an ellipse resulting from not accurate unloading). At the exit, we get stacks of napkins divided in the specified number. The painting module applies a two-color block-type drawing, that is, on each napkin, you can place a logo or an image in any chosen place. The brightness of the image is controlled by the consistency of the paint.It is possible to order several clich�© shafts with different patterns; their replacement does not require special qualifications from the mechanic. Technological cycle: preliminary unwinding of the roll -> drawing: two colors -> drying -> paper embossing -> primary paper folding -> secondary paper folding -> paper cutting into napkins -> finished product exit.
Grain Energy LLC produces aerodynamic grain separators "ASM" with a capacity of 5 to 50 t/h intended for cleaning and calibration: wheat, barley, flax, soybeans, coffee, sunflower, corn and other crops. Minimal energy consumption due to the use of a frequency converter of European production. The efficiency of the separator is VERY high. The output of the cleaned and calibrated material occurs through 7 trays: - the first gets the largest debris (stones, pieces of earth, stems, spikelets, etc.); - material from the middle part of the ear, corn cob or sunflower cap gets into 2-3 trays. This is the most viable material of the whole heap, seed germination rate up to 98%; - material from the bottom of the ear gets into 4-5 trays - this is commercial grain, varietal, which will bring the maximum profit - grain from the upper part of the ear (unripe, light, halves, crushed grain) falls into 6-7 trays. Which in an unclean heap significantly reduces the cost of the harvested crop! Advantages of the ASM grain cleaning machine �· Work with material of any moisture and debris; Versatility - works with any bulk materials: grain, groats, chaff, etc. Low power consumption; All parts are cut by plasma cutting - precision during assembly and quality of the separator; high performance; Only high-quality European components; Does not require complex care and maintenance; Modular assembly-disassembly system; During aerodynamic separation the seed is not injured, the marketable grain has a high degree of purification from grain, mineral and other impurities. Allows you to prepare high-quality and viable seed 2 years warranty. Grain Energy LLC successfully sells equipment to the countries: Ukraine, France, Lithuania, Latvia, Albania, Bulgaria, Romania, Hungary, Austria, Germany. We carry out dispatch and support of equipment for export. We are looking for partners in your country.
Automatic circuit breaker tester UPA-3 is designed for testing and ampere-second characterization of automatic AC current circuit breakers. The device allows registering the value of the supplied current and timing the automatic circuit breaker switching interval. Circuit breaker tester UPA-3 is a mobile device, which could be easily transported to a required testing location. Circuit breaker tester UPA-3 operates on the principle of varying the power in the primary circuit of the matching power transformer and, respectively, varying the output current, flowing through the automatic circuit breaker under the test. Power regulation could be done either through an external regulator (RNO or VR) or through a built-in thyristor controller.
Oil testers bring out accurate and repeatable results of measured breakdown voltage. Fast high-voltage switch off time makes it possible to carry out test of dielectric liquids, which are easily destroyed under such influences. The internal design of olt testers combined with a use of automatic high voltage breakers, cutting off supplied voltage if tester?s lid has been opened during the test, provide operator with high level of safety. Testers are fully equipped and are ready for operation right after unpacking. They come with a test vessel (iec 60156 ? basic configuration) with vde 0370 mushroom-shape electrodes. A gap between electrodes is easily regulated with a use of pass-no pass gauge, which comes in pack. A-series provides with fully automatic test procedure according to selected standard (basically iec 60156 and gost 6581 settings are preloaded). It has a built-in printer which is able to print a test report after procedure is done. Test results are saved into non-volatile memory of olt oil tester. A pc-connectivity makes it easy to collect data from olt oil tester, save and store them as well as print a fulfilled report. Test voltage is being measured directly on electrodes. This fact combined with a true sine voltage shape (independent from supply voltage shape), increases repeatability and accuracy of measurements. Test vessel for this series goes with magnetic stirrer, which stirs a liquid between two measurements. Main features: Compact and lightweight Fully automatic operation Fully compatible with iec 60156 Preloaded testing programs for different standards Built-in printer Pc connectivity Internal test data storage Precise direct voltage measurement True sine high-voltage on electrodes Oil temperature measurement
Oil testers bring out accurate and repeatable results of measured breakdown voltage. Fast high-voltage switch off time makes it possible to carry out test of dielectric liquids, which are easily destroyed under such influences. The internal design of olt testers combined with a use of automatic high voltage breakers, cutting off supplied voltage if testerâ??s lid has been opened during the test, provide operator with high level of safety. Testers are fully equipped and are ready for operation right after unpacking. They come with a test vessel (iec 60156 â?? basic configuration) with vde 0370 mushroom-shape electrodes. A gap between electrodes is easily regulated with a use of pass-no pass gauge, which comes in pack. A-series provides with fully automatic test procedure according to selected standard (basically iec 60156 and gost 6581 settings are preloaded). It has a built-in printer which is able to print a test report after procedure is done. Test results are saved into non-volatile memory of olt oil tester. A pc-connectivity makes it easy to collect data from olt oil tester, save and store them as well as print a fulfilled report. Test voltage is being measured directly on electrodes. This fact combined with a true sine voltage shape (independent from supply voltage shape), increases repeatability and accuracy of measurements. Test vessel for this series goes with magnetic stirrer, which stirs a liquid between two measurements. Main features: Compact and lightweight Fully automatic operation Fully compatible with iec 60156 Preloaded testing programs for different standards Built-in printer Pc connectivity Internal test data storage Precise direct voltage measurement True sine high-voltage on electrodes Oil temperature measurement