The pipe is manufactured from 100% virgin unplasticized polyvinyl chloride compound (PVC-U). No re-worked material is used. The pipe is produced under an ISO 9001-2000 Quality System.
Duzgunler Plastic pipes are produced in a range of pressure ratings 4, 6, 10 and 16 Bar. Duzgunler Plastic pipes are produced in a range of nominal pressure (PN) at 20°C. The appropriate derating factors should be applied for working pressures when subjected to higher temperatures. The nominal outside diameters and nominal wall thickness are based on an overall service (design) coefficient C=2,5 from 50 mm.to 90 mm. and C= 2 from 110 to 355.
Duzgunler Plastic pipe is used in a wide range of applications, such as:
* Irrigation systems main/sub-mains.
* Chemical industrial processes.
* Pressurized water supply
(city town, industrial, home, commercial.)
* Drainage/sewage applications.
* General services, domestic water, A/C drainage.
* Ducting, electrical, telecommunication.
* Industrial process plants oil/gas/petrochemical.
* Desalination processes, brine disposal, mineral water
Features of Duzgunler Plastic U-PVC pipes:
* Fully compliant with TS 274 EN 1452 and ISO standards.
* Resistant to a wide range of chemicals and corrosion.
* High Impact Resistance
* Quality assured and tested to the strict specifications of the standard for dimension compliance, impact resistance, burst pressure, flattening & joint tightness.
* Smooth internal bore for low friction losses.
* Compatible with the full range of PVC-U Pressure fittings.
* Long service life under a wide range of conditions.
* Will not support combustion.
There are 4 types according to their pressure resistance:
PN4
PN6
PN10
Pn16
Technical Features:
Raw Material: U-PVC
Standard: TS 274 EN 1452
Dimension: Pipes produced in ranging from Ø 50 mm. dia. up to Ø 400 mm. dia.
Normally supplied in 6 m length Others can be supplied on request.
Connection: rubber ring joint for all size
Technical Features:
-Gravity: 1350 < p < 1460 kg/m²
-Opaque: max. % 0,2
-Deformation heat: 80 C
-Resistance to diklormetan: Resistant
-Quantity of vinilcloridmonome: less than 1ppm
-Resistance of int. Pressure: Two times of nom pressure
-Resistance to stroke: TIR < % 10
Variety kinds of fixing materials (clamps), including multifunctional profiles, dowels, nuts,
Screws, bolts, pipe clamps( pipe clamps with head, pipe clamps with nut, pipe clamps with combi nut, pipe clamps for heavy load with nut, pipe clamps for heavy load with head, pipe clamps with bolt, pipe clamps used for ventilation purposes, pipe clamps with (without) rubber, double pipe clamps, multifunctional clamps. Channels as (u, c), g-clips and other products.
Compared to other plastic hoses in the market, techniflex polyurethane hoses (techni pu) have the following distinguishing characteristics:
Compared to rubber hoses, techniflex polyurethane hoses have greater flexibility and lower weight
Hoses are more usable at low temperatures because of their flexibility. The risk of bending fracture is lower at low temperatures. They have easy bending characteristics, so that there is no mechanical stress in connection points.
Wear is less i. E. About 3 to 4 times better than many soft pvc, 2.5 to 5 times better than rubber and aboutstrength at high temperatures compared to pvc hoses.
Polyurethane hoses have the advantage of high elasticity, high tensile strength, high resistance to tear propagation, best resilience and low compression set
High compression strength (it provides greater safety due to material stability)
It has advantages in case of fire (compared to pvc)
Environment friendly. Cost effective due to long usage period.
Rubber hoses are usually black and opaque therefore it is not possible to see and control the particles during the transfer process. Techni pu hoses are transparent which provides secure working area.
Good chemical resistance
Good resistance to uv and weather conditions.
The most important factor in tunnel and mining applications is to pres or vacuum the required air into the tunnel or mining areas. Because of the nature of the tunnel/mining areas, there are turning points and sloped areas. In these cases, techniconnect hoses have higher performance. At bending or turning points, the vertical and horizontal section does not change because of the spiral and the pressure loss is very lower. The most effective, safety and practical way of suction the air from tunnel/mining is techniconnect hoses. The advantages of the hoses are;
Practical, easy installation with connection elements and hanging apparatus
Cross section area does not change in turning or bending points
Vacuum is possible
Long service life
Mechanical endurance factor in underground
Benefit/cost ratio is higher
Lower pressure loss compared with classic air ducts
We products drip irrigation pipe q16-20 mm diameters 2-4 l/h and 0, 9 - 1 mm wall thickness
Pe pipe is pe 100 hdpe and pe32 ldpe diameters q16 to 160 mm
Q16 mm pipe 400 meter roll
Q20 mm pipe 300 meter roll
We are one of the main producer of PPR-C type 3 pipes and fittings and proud of our quality and pricing.
Our products comply with Turkish, Russian, European Standards, and our quality is assured by ISO 9002.
The Pipes of the Future: Lightweight, Strong, Reliable GRP Pipes!"
Filament winding is a technique used in the manufacturing of glass fiber reinforced polymer (GRP) pipes. This method involves wrapping glass fiber filaments around a mold, typically a cylindrical mandrel, to form the pipe. The fiber-reinforced structure is then impregnated and hardened with polymer resin, resulting in a durable and lightweight material known as GRP pipe.
GRP pipes produced using this technique are commonly used in chemical industries, water and wastewater treatment plants, the maritime sector, and the oil industry. This material is preferred for its corrosion resistance, lightweight nature, and high strength. Different types of glass fiber reinforced polymer materials, such as GRV (glass reinforced vinyl ester) and GRE (glass reinforced epoxy), can also be produced using the filament winding method. The properties and applications of these materials may vary depending on the type of resin used and the structure of the reinforcing material
"Begendi Industry is committed to providing top-level quality standards with the production of Fiber Winding Technology, equipped with state-of-the-art 4-6 Axis fully automatic CNC-controlled machines. This innovative approach promises production precision and reliability that goes beyond industry standards, in addition to offering customers excellent quality products.
As a company, we comply fully with industry standards such as AWWA, ASTM, ISO, EN, DIN, and BS, with our production capacity ranging from DN 200 mm up to DN 6000 mm. We manufacture pipes ranging from 200 mm to 4000 mm in diameter, with pressures ranging from 1 bar to 120 bar.
Our areas of expertise include drinking water projects, irrigation projects, energy power plant projects, "jacking" pipe manufacturing that allows for trenchless installation, waste and stormwater projects, natural gas pipelines, and oil pipelines. Our leadership in the industry reflects our commitment to providing customers with reliable and durable products through our technological superiority and rigorous quality control processes."
