Beet Sugar, Coal, Steel Rebars, Hms Scrap..
Product Code Product Description PRS-AS0135 Water in Bituminous Materials Test Set (Dean-Stark Method) 220-240 V 50 Hz STANDARDS : ASTM D95, D244; AASHTO T55, T59; IP 74/77; CNR No.101; NLT 123 The PRS-AS0135 test set is used for determining the water content of bituminous materials. The test is based on distilling the sample with a volatile solvent. The material to be tested is heated under reflux with a water immiscible solvent, which distills together with the water in the sample. Condensed solvent and water are continuously separated in a trap, the water settles in the graduated section of the trap, and the solvent returns to the still. Test Set Consists Of; â?¢ Electric Heater with Thermo Regulator â?¢ Glass Condenser â?¢ Glass Receiver â?¢ Glass Still, 10 ml Dimensions 200x200x450 mm Weight (approx.) 4 kg Power 250 W
icumsa45 brazil sugar 99.80%, granule sulphur 99.5-99.8% purity, lump sulphur 99.9%, thermal (steam) coal 4800 kcal/kg up to 6100 kcal/kg (nar).Export
Lignite, brown coal, coal, bauxite, copper,.Export
Stone coal.Import and export
Steam generators, steam boilers, thermal oil boilers, high pressure solid fuel intrinsic stoker steam boilers, steam boiler with front furnace, hot water boilers, electrical water heaters, economizers, superheated steam boiler, expansion and hydrofor tanks, accumulation tanks, single & double serpentine water heaters.
Petrol, copper wire scrap, copper cathode, minerals, coal, cement, rebar.Import, export
Polymer-modified bitumen compound for a bituminous covering layer of a roof sheet, a bituminous roof sheet and a fully recyclable roof sheet
The vertical shaft crusher performs the crushing process by multiplying the crushing chamber which is composed of the same material and the crushing chamber composed of the same material in order to accelerate the material to be crushed. The material to be broken is directed into the rotor through the feed chamber. The material exiting the rotor hits the crushing chamber at a speed of approximately 200-250 km / h. 3 types of breaking action takes place. These are impact, splitting and abrasion. The path of the material to be broken in the crusher proceeds by rubbing the primers covered with almost stone material. This significantly reduces wear on the mechanical part of the machine. Vertical shaft crushers perform hard, abrasive, small grain, wet, damp or sticky feeding materials easily. These materials can be found in all applications listed in the following list: For breaking 7-30 mm natural stone which is not used in creek materials. In case of high 0-5 material ratio in limestone, basalt and dolomite quarries, If cubic material is required in limestone, basalt and dolamite, Production of sand, gravel and gravel in the required dimensions for concrete and asphalt, In the production of materials including fine-grained products used for road infrastructure, Sands whose technical characteristics are determined by standards, In the process of breaking the cement material in order to maximize the small particle size by reducing the grain size in the mill before the process, Can be used in the addition of coking coal to liquid steel by spraying.
Horizontal driller machine and spare parts.
Product Code Product Description PRS-ASVP00127 Vakuum Pyknometer STANDARDS : EN 12697-5,EN 13108,ASTM D2041,AASTHO T209,T283 Transparent plexiglass made, complete with valve and gauge. it is used for a rapid determination of asphalt content, bulk specific gravity of aggregates. The max. theoretic specific gravity of bituminous uncompacted road mixtures and the percent air voids in compacted mixtures. Dimensions dia. 300x450 mm Weight 10 Kg
PRS-ASTH1322 Asphalt Mixer STANDARDS : ASTM C109, C305 / AASHTO T106, T162 / EN 196-1, 196-3:2005, 413-2, 459-2, 480- This 5 litre capacity mixer has been designed to mix bituminous samples for compaction tests and for other tests where uniformity is required. Thanks to the planetary action this mixer ensures a complete and uniform mixing. The machine is provided with a variable speed drive allowing to set different speeds. The plastic cover can be lifted to inspect the boxl, and in this case the motor automatically turns off to prevent accidents to CE safety Directive. The mixer is supplied complete with hook beater and stainless steel bowl, but without the insomantle electric heater that must be ordered separately. Dimensions 260 x 760 x 860 mm Power supply 400 V 50 Hz 3 ph 0,5 HP (230V 1 ph on request ) Weight 160 Kg
Product Code Product Description PRS-AS0056 Automatic Marshall Stability Test Machine, 50 kN, 220-240 V 50-60 Hz PRS-AS0056/110 Automatic Marshall Stability Test Machine, 50 kN, 110 V 60 Hz PRS-AS0057 Breaking Head (Stability Mould) 4â?� PRS-AS0058 Breaking Head (Stability Mould) 6â?� PRS-AS0060 Linear Potentiometric Displacement Transducer, 25x0.001 mm with bracket for PRS-AS0057 and PRS-AS0058 PRS-AS0063 Indirect Tensile Splitting Device for Compacted Bituminous Samples 100 mm (4â?�) Dia. STANDARDS : EN 12697-34, 12697-23, 12967-12 (Method A and Method B up to 51 mm/min); ASTM D1559, D5581, D 6927; AASHTO T245 The PRS-AS0056 50 kN Capacity Automatic Marshall Stability Test Machine is used to determine the maximum load and flow values of bituminous mixtures. The machine comprises of a robust and compact two column frame with adjustable upper cross beam. The unit is a bench mounting compression frame with motor and worm gear housed within the base unit. The speed of the lower platen can be adjusted between 6 mm/min to 60 mm/min using the Data Acquisition and Control Unit. For safety, the up and down travel of the lower platen is limited the use of limit switches. Rapid adjustment of the platen is controlled using the up and down buttons on the front panel of the machine. The machine can be hand operated by a lateral hand wheel for calibration purposes. The measuring system consists of a 50 kN capacity strain gauge load cell fitted to the upper cross beam to read stability values and the 25 x 0.001 mm linear potentiometric displacement transducer fitted to the Breaking Head. The PRS-AS0056 Automatic Marshall Stability Machine is suitable for testing 6â?� dia. specimens (152.4 mm) conforming to ASTM D5581.
Product Code Product Description PRS-ZE0630 Vibratory Compactor Set, 220-240 V 50 Hz PRS-ZE0750 CBR Type Mould BS (modified proctor) Vibrating Hammer Mould EN PRS-ZE0768 C Spanner for PRS-ZE0750, 2 pcs PRS-ZE0770 Assembly Tool for Base Plate for PRS-ZE0750 STANDARDS: EN 13286-4; BS 1377:4 / EN 12697-9, 12697-10, 12697-32 The PRS-ZE0750 Vibratory Compactor Set is used to prepare the test specimens of road base and sub base materials by using the vibratory compaction technique. The specimens prepared from road base and sub base materials is used for the proctor and CBR tests. The set is also used for preparing the test specimens of bituminous mixtures PRS-ZE0750 mould with base plate and extension collar should be ordered separately and also when ordering PRS-ZE0750, PRS-ZE0768 and PRS-ZE0770 should be ordered separately for assembling and dissambling. The Vibratory Compactor Set is supplied complete with; â?¢ Vibrating Hammer â?¢ Supporting Frame â?¢ Small Tamping Foot, 102 mm dia. â?¢ Large Tamping Foot, 146 mm dia. â?¢ Shank, 300 mm Dimensions 510x300x1120 mm Weight (approx.) 75 kg (complete set) Power 1150 W (vibrating hammer)
Product Code Product Description PRS-AS0630 Vibratory Compactor Set, 220-240 V 50 Hz PRS-AS0085 P.R.D. Split Mould and Base Plate STANDARDS : EN 12697-32, 12697-9, 12697-10 The PRS-AS0630 Vibratory Compactor Set is used to prepare test specimens of bituminous mixtures by using the vibratory compaction technique. The PRS-AS0630 Vibratory Compactor Set consists of a Vibrating Hammer (220-240 V 50 Hz), Supporting Frame, 102 mm dia. Small and 145 mm. dia. Large Tamping Foots and 300 mm Shank. P.R.D. (Percentage Refusal Density) Split Mould is split verticially on one side, attached to the base plate with clamp. Plated against corrosion. The split mould and base plate should be ordered separately. The set is also used for compaction of proctor and CBR soil specimens. The Vibratory Compactor Set is supplied complete with; â?¢ Vibrating Hammer â?¢ Supporting Frame â?¢ Small Tamping Foot, 102 mm dia. â?¢ Large Tamping Foot, 145 mm dia. â?¢ Shank, 300 mm, long Dimensions 510x300x1120 mm (complete set) Weight (approx.) 75k (complete set) Power 1150 W (vibrating hammer)
Marshall Stability Test Machine with Digital Readout Product Code Product Description PRS-AS0055 Marshall Stability Test Machine with Digital Readout Unit, 50 kN, 220-240 V 50-60 Hz PRS-AS0055/110 Marshall Stability Test Machinewith Digital Readout Unit, 50 kN, 110 V 60 Hz PRS-AS0057 Breaking Head (Stability Mould) 4â?� PRS-AS0058 Breaking Head (Stability Mould) 6â?� PRS-AS0060 Linear Potentiometric Displacement Transducer, 25x0.001 mm with bracket for PRS-AS0057 and PRS-AS0058 PRS-AS0063 Indirect Tensile Test Jig for Compacted Bituminous Samples 100 mm (4â?�) & 150 mm (6â?�) Dia. STANDARDS : EN 12697-34, 12697-23, 12697-12 (Method A); ASTM D1559, D5581, D 6927; AASHTO T245 The PRS-AS0055 50 kN Capacity Automatic Marshall Stability Test Machine is used to determine the maximum load and flow values of bituminous mixtures. The machine comprises of a robust and compact two column frame with adjustable upper cross beam. The unit is a bench mounted compression frame with motor and worm gear housed within the base unit. The mechanical jack raises the lower platen at a constant speed of 50.8 mm/min as required in the relevant standard. For safety, the up and down travel of the lower platen is limited the use of limit switches. Rapid adjustment of the platen is controlled using the up and down buttons on the front panel of the machine. The measuring system consists of a 50 kN capacity strain gauge load cell fitted to the upper cross beam to read stability values, the 25 x 0.001 mm linear potentiometric displacement transducer fitted to the Breaking Head and two digital readout units (one for load and another for displacement) The PRS-AS0056 Automatic Marshall Stability Machine is also suitable for testing 6â?� dia. specimens (152.4 mm) conforming to ASTM D5581. The machine can be hand operated by a lateral hand wheel for calibration purposes; the hand wheel is supplied complete with the machine. Platen Speed 50,8 mm/min Capacity 50 kN The PRS-AS0055 Marshall Stability Test Machine is supplied complete with; â?¢ Load Cell, 50 kN â?¢ Linear Potentiometric Displacement Transduce with Bracket, 25x0.001 mm â?¢ Hand Wheel for Manual Control â?¢ Breaking Head, 4â?� Dimensions 550x700x1200 mm Weight (approx.) 102 kg Power 1100 W
Product Code Product Description PRS-AS0140/A Bitumen Oven for Rolling Thin-Film Oven Test (RTFOT), ASTM 220-240 V 50-60 Hz PRS-AS0140/E Bitumen Oven for Rolling Thin-Film Oven Test (RTFOT), EN 220-240 V 50-60 Hz PRS-AS0142 Spare Glass Container for PRS-AS0140 PRSGE-AS3572 Air-Drying Unit for PRS-AS0140 STANDARDS : EN 12607-1; ASTM D2872; AASHTO T240 PRS-AS0140 Bitumen Oven is used for determination of the resistance to hardening of semisolid asphaltic materials/ bitumen or bituminous binders under the combined effects of heat and air with the rolling thin-film oven test (RTFOT) method. The Internal chamber of PRS-AS0140 Bitumen Oven is manufactured from stainless steel, insulated with fiberglass or similar, the door has a symmetrically located window. The oven has a programmable temperature controller which works in PID mode and digital display system. A temperature sensor is used instead of the ASTM 13C thermometer. The temperature can be read from the digital unit placed on the oven. Over tempereture controlled by a mechanic switch. Conforming to the CE Directives. Air Compressor and Air-Drying Unit (PRSGE-AS3572) should be ordered separately. Maximum pressure should not exceed 2 bar when an air compressor is used. The Bitumen Oven for RTFOT is supplied complete with; â?¢ Glass Comtainers, 8 pcs. Dimensions 800x700x750 mm Weight (approx.) 62 kg
Product Code Product Description PRS-AS0030 Centrifuge Extractor 1500 g, 220-240 V 50-60 Hz PRS-AS0030/110 Centrifuge Extractor 1500 g, 110 V 60 Hz PRS-AS0031 Filter Paper 250 mm Outer dia. 45 mm Inner dia. for PRS-AS0030 (100 pcs / Pack) PRS-AS0032 Rotating Bowl and Cover for PRS-AS0030 PRS-AS0035 Centrifuge Extractor 3000 g capacity, 220-240 V 50-60 Hz PRS-AS0035/110 Centrifuge Extractor 3000 g capacity, 110 V 60 Hz PRS-AS0036 Filter Paper 295 mm Outer dia. 45 mm Inner dia. for PRS-AS0035 (100 pcs / Pack) PRS-AS0037 Rotating Bowl and Cover for PRS-AS0035 STANDARDS : EN 12697-1 Clause B.1.5; AASHTO T164 A; ASTM D2172 A The Centrifuges are used for the determination of the bitumen percentage in bituminous mixtures. All models comprise a removable precision-machined rotor bowl housed in a cylindrical aluminum box. The bowl is driven by an electric motor fitted with an AC drive (inverter) with the double function of speed control up to 3600 rpm regardless of the frequency (50 or 60 Hz) and electrical breaking. The centrifuge can be set for the automatic speed ramp up to 3600 rpm and will stop in 10-15 seconds. The cover is precisely machined and fitted with a solvent resistant gasket to avoid leakages. The control panel includes: Start/Stop button and speed control knob. The Centrifuge Extractor is supplied complete with; â?¢ Bowl and Cover, â?¢ Filter Paper - 100 pcs. Dimensions 450x650x550 mm Weight (approx.) 50 kg (for both models) Power 370W (for both models)
Product Code Product Description PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer 220-240 V 50-60 Hz PRS-AS0120/110 Semi-Automatic Digital Bitumen Penetrometer 110 V 60 Hz PRS-AS0121 Transfer Dish for PRS-AS0120 PRS-AS0122 Sample Cup, � 55x35 mm, stainless steel PRS-AS0123 Sample Cup, � 70x45 mm, stainless steel PRS-AS0124 Penetration Needle, 2,5 g PRS-AS0160 One-Quarter Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126 PRS-AS0161 One-Half Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126 PRS-AS0162 Penetrometer Cone ASTM D 217 (Optional Type) and ASTM D 937, for PRS-AS0120 and PRS-AS0126, Brass PRS-AS0165 Resilience Ball Penetration Tool. ASTM D5329, for PRS-AS0120 and PRS-AS0126 STANDARDS : EN 1426; ASTM D5; AASHTO T49 The PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer is used to determine the penetration of bituminous samples under constant load, time and temperature. The Penetrometer consists of a cast iron base with coarse and fine levelling screws, a digital penetration measurement gauge 0.01 mm readability and a penetration timer unit. Start button of the penetration timer unit is used to release the plunger fitted with the needle to start the 5 seconds test. A water bath (PRSGE-AS4000 or PRSGE-AS4050, 25±0,1 C) and a thermometer ( IP38, ASTM 17C or 63C ) required for the test should be ordered separately. The Semi-Automatic Digital Bitumen Penetrometer is supplied complete with; � Penetration Needle, 2,5g, 1 pieces � Transfer Dish � Sample Cup � 55x35 mm, 3 pieces, stainless steel Dimensions 200x300x500 mm Weight (approx.) 16 kg
Manual Softening Point Apparatus (Ring and Ball Test Sets ) Product Code Product Description PRS-AS0130 Ring and Ball Test Set, 220-240 V 50-60 Hz PRS-AS0130/110 Ring and Ball Test Set, 110 V 60 Hz PRSTD-1410 Hot Plate with Magnetic Stirrer PRS-AS0131 Brass Ring, with Steel Ball and Ball Centering Guides, 2 pcs.each PRS-AS0132 Ring Holder and Assembly PRSGG-1330 Borosilicate Glass Beaker 600 ml PRSGT-1305 Glass Thermometer Max. 110°C PRSGT-1315 Glass Thermometer Max. 250°C PRSGT-2050 ASTM 15C Thermometer -2 +80°C (IP 6OC) PRSGT-2055 ASTM 16C Thermometer +30 + 200°C (IP 61C) STANDARDS : EN 1427; ASTM D36; AASHTO T53 PRS-AS0130 Ring and Ball Test Set, 220-240 V 50-60 Hz The PRS-AS0130 Ring and Ball Test Set is used for determining the softening point of bituminous materials by ring and ball method. If required, Glass Thermometer PRSGT-1305, PRSGT-1315, ASTM 15C or 16C Thermometer should be ordered separately. The Ring and Ball Test Set is supplied complete with; � Hot Plate with Magnetic Stirrer � Brass Rings, 2 pcs. � Ball Centering Guides, 2 pcs. � Thermometer, Temperature Sensor with Holder � Steel Balls, 9.5 mm dia., 2 pcs. � Ring Holder and Assembly � Borasilicate Glass Vessel Beaker 600ml Dimensions 280x400x200 mm (packed) Weight (approx.) 4 kg Power 650 W
