"By-Pass Lopper *Upper Blade: SK5, Non-Stick Teflon *Lower Blade: S50C, Plating *Handle: PP(Orange021C)/TPR(Black), Alum. "
Equipment summary: RT-101 Moving die rheometer is a widely used tester in rubber processing industry, rubber quality control and basic research rubber, For optimize formula of rubber provide accurate data, It can accurately measure the scorch time, rheometer time, sulfide index, the maximum and minimum torque and other parameters. Main functions: RT-101 Moving die rheometer used monolithic rotor control, which include: host, temperature measurement, temperature control, data acquisition and processing, sensors and electrical chains and other components. These measurements, temperature control circuit consists of a temperature control device, platinum resistance, heater composition, capable of automatic tracking power and ambient temperature changes, automatically correct PID parameters to achieve fast and accurate temperature control purposes. Data acquisition system and mechanical linkage to complete the rubber vulcanization process of force torch signal automatic detection, automatic real-time display of temperature and settings. After curing, automatic processing, automatic calculation, print vulcanization curve and process parameters. Show curing time, curing power Ju, also has a variety of audible alert. RT-101 Moving die rheometer controlled by computer, the computer setting the parameters of the direct control of test parameters rheometer. Display real-vulcanization curve and temperature curve, store test results, different adjustable comparison of test results and in a different color. Applicable industry: Widely used in rubber products industries. corresponding standard : Accord with GB/T16584 ISO6502:1991 and ASTMD5289-95 Technical parameter: Model: RT-101 Standard: GB/T16584 IS06502 Temperature: room temperature to 200 Centigrade Heating-up: 15 Centigrade/min temperature fluctuation: = ±0.3 Centigrade temperature resolution : 0.1 Centigrade torque range: 0-5N.M,0-10N.M,0-20N.M torque resolution: 0.001NM Power: 50HZ, ~220V±10% Pressure: About 0.4Mpa Air-pressure requirement: 0.5Mpa--0.65MPa (user prepare the dia 8 trachea) Environment temperature : 10 Centigrade--20 Centigrade Humidity range: 55--75%RH Compressed air: 0.35-0.40Mpa Swing frequency : 100r/min(about 1.67HZ) Swing angle: ±0.5 Centigrade ,±1 Centigrade ,±3 Centigrade Printing: Date,time,temperature,vulcanization curve,temperature curve,ML,MH,ts1,ts2,t10,t50,Vc1,Vc2.
Application: suitable for cutting stainless steel ?hard alloy, etc. Machine:used on portable angle grinder Usage: preparation work before welding, grinding weld, cleaning burr & rust, surface polishing, edge grinding, etc. Advantage: high grinding efficiency, long service life, high cost performance, comfortable for operator. Specifications: D×h×d Abrasive Grit Hardness Max. R.P.M. 100x4x16 4"x1/6"x5/8" Wa 46 Q 15200 100x6x16 4"x1/4"x5/8" Wa 30 Q 15200 125x6x22 5"x1/4"x7/8" Wa 30 Q 12200 150x6x22 6"x1/4"x7/8" Wa 24 Q 10200 180x6x22 7"x1/4"x7/8" Wa 24 Q 8500 According to customer's requirements.
Application: Suitable for cutting common carbon steel?tool steel?cast iron, etc. Machine:Used on portable angle grinder Usage: Grinding weld?cleaning burr & rust?surface polishing, etc. Advantage: High grinding efficiency, long service life, high cost performance, comfortable for operator. Specifications: D×H×dD×H×dABRASIVEGRITHARDNESSMAX. R.P.M. Packaging 100X4X164"X1/6"X5/8"A46Q15200280 100X6X164"X1/4"X5/8"A30Q15200200 125X6X225"X1/4"X7/8"A30Q12200100 150X6X226"X1/4"X7/8"A24Q10200100 180X6X227"X1/4"X7/8"A24Q850080 According to customer's requirements .
Place of Origin Ma Anshan,Anhui,China Brand Name Exact or as request Item Bimetal thermometer Dial Material Alu. Dia. Size 2.5", 3", 4", 5",6" Accuracy 2.5% Case black steel Bezel chrome plated steel Lens Glass Thread 1/2" NPT, 1/2"BSP, etc. Connection Material S.S. Pressure Range -40?-0-500? Mounting type bottom Filled Dry
Type T : All Angle Adjustable Bi-thermometer Application: This kind of bimetal thermometer has an all-angle swivel connection. The hermetically-sealed case offers protection from weather and dust, and is guaranteed against fogging up. The bimetal helix is coated with a viscous silicone to minimize pointer oscillation and improve temperature transmission. Dial Size: 2.5",3", 4" 5", 6" Stem diameter: F6.3, F8, F10 Stem length: 65mm, 100mm, 150mm, 200mm, 300mmn Connection thread: 304SS with 1/4”, 1/2”, 3/4” NPT , BSP, BSPT Case: 304 stainless steel Bezel: 304 stainless steel ring Range: -40ºC / ºF to 500ºC / ºF Window (lens): Polycarbonate lens, tempered glass available Accuracy: 1.6% full scale Option Info: Other materials, ranges, connections are available upon request
Tool machine control box The tool machine control box business becomes the main business of daegun technology, started 2004, and annually produces 2600 of tool machine control box. We produce all type of control box for big and small. We prepare test bench program always to satisfy customers’ demand, and construct customers’ order production. Currently, produce turning center purpose control enclosure of puma series, next generation multi control enclosure unit, and swiss turn turning center purpose of st 20g series.
Application Electronic Crockmeter, to determine the colour fastness of textiles to dry or wet rubbing. A pinned acrylic sample holder ensures rapid sample mounting and repeatability of results. Crockmeter Fitted with a pre-determined electronic counter for strokes up to 999,999 times. Specification Rubbing head: Dia.16mm Vertical pressure: 9N+/-10% Rubbing stroke: 104mm Counter: 1-999,999 times, automatically stops Included Accessories AATCC rubbing clothing: 1 box Sand paper: 2 (pcs) Rings: 2 (Pcs) Standards: ISO 105x12/D02, AATCC 8/165, BS 1006-D02, BS 4655, NEXT 10, M&S C8/C8A/C25/C52 Power: 220/110V 50/60Hz 2A Weight: 25 Kg Dimensions: 550x230x260mm (LxWxH)
The feature of the PCD inserts: 1. The PCD insert meets the international ISO standard, size can be customized too. 2. In highly abrasive, extremely hard harsh geological environmen.PDC insert' life can reach 3~5 times than the normal carbide inserts. 3. The cutting edge of PCD insert is sharp, the hardness and wear resistance of the PDC insert is 100 times than the carbide inserts (theoretical value). It can realize high speed cutting and hard material cutting with high work efficiency and facilitate fast clamping. 4. Our PCD insert can be used repeatedly, which helps to lower your processing cost. 5. Reduce equipment loss and influence to the device of load mutations. PCBN Products: Grade & Option For Machining Place of Origin: Hunan, China (Mainland) Brand Name: ZZ Hardmetal Model Number: standard Material: Hard Alloy Usage: External Turning Tool Hardness: 3000~3400HV(MPa) Coating: PCD/PCBN Workpiece: steel, cast iron, non-ferrous metal stainless steel, aluminium Quality: long life and high working efficiency Application: Machining Cutting coating Grade: ZZ3500, ZZ3600, ZZ7000, ZZ7500, ZZ7600, ZZ9000, ZZ9500, ZZ9600 Certification: ISO9001:2008 Cutting Condition: Dry/ Wet keyword: diamond insert
Model SG-213B Description Three Claws Cups Durable Aluminum Rubber Glass Suction Plate Lifter Glass Sucker Material Aluminium alloy, Rubber and Plastic Color Golden or customized Application all kinds of glass partition glass doors,shower doors, glass panels/walls Horizontal Suction: 155KG Vertical Suction: 145KG Packing details Blank Packing or Color Packing. Specifications: 1.High quality aluminium alloy, rubber plate plastic handle. 2.Oil painting on surface, prevent product from stain . 3.Safe for using. Product Description: 1.Our product is made from high quality aluminium alloy as body and natural rubber as plate. great suction power. 2.Product surface is completely covered with oil paint, which keeps the product from stain. 3.Great pump glass suction capacity, durability. 4.Suction plate pump lifting tool, can be used in lifting and installing glass. Features: A)Material: aluminum alloy and rubber or high grade material (aluminium die-casting ) B)Packing: cartons or as per customers' request C)High strength die-casting alloy body, safe and durable D)Hold different weight from 30kgs to 155 kgs E)Application: Suitable for all kinds of glass partition glass doors,shower doors, glass panels/walls ect. F) Easy to install, the creative design vividly foretelling the shape of the new trend.
Stainless Steel C Glass Clamp, Glass Clip Flat, Glass Holder Made In China Hot Sale Glass Clamp!!! Flat back!! Material Zinc alloy, 304SS, 316SS, 316LSS Finish Satin, Mirror, Titanium Glass Thick 10/12mm(6/8mm please order gaskets to suit ) Capacity When vertically positioned 2 clamps can support approx 60-80Kg per pair
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod ma
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod ma
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod ma
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Cable joint as an important connection point of the whole power supply network, its running stability will directly affect the quality of the power supply system. Because the cable joint is made artificially in the on-site installation is complete, the environment affected by the construction and operation of the environment, will inevitably cause the error of installation, external damage, cable breakdown caused by explosion and water etc. And in the cable joint breakdown and explosion will release a lot of energy, the surrounding power facilities or personnel to cause harm, or even cause the occurrence of the two accident. To solve these problems, our company developed with fire prevention, waterproof, explosion-proof function scotchcast resin cable joints, all-round protection, once the explosion or breakdown of cable joints, can effectively protect the surrounding power facilities and other personnel, prevent the occurrence of two damage.
