Skeleton caulking gun Item no.: bc-1053 9 inches for 310 ml cartridgehex rod Powder coated surface finish Zinc coated rodwelding construction C shape ladder hook Item bc-1054: steel trigger with finger Packing: Package: each piece in one plastic bag, 40pcs per outer cartonouter packing: 345x260x385mm Gross/net weight: 14/13kgs;
P20/ 1.2311/ 618 steel: 1.Hardened&tempering 2.Hot rolled or forging 3.Black or machined surface 3.Hardened, hrc:28~34 Standard seaworthy packing
DTH Hammer of Sandvik Make is 4" in Diameter. Its Button bit dia. is 4.5". It is used in drilling in rock mines.In hard rock its life is 30000ft to 35000ft.
FORGING:Heating for forging must be done slowly and uniformly. Soak through at F and reheat as often as necessary, stopping work when the temperature drops below 1700 After forging, cool slowly in lime, mica, dry ashes or furnace. D2 should always be annealed after forging. ANNEALING: Heat slowly to 1550 , hold until entire mass is heated through, and cool slowly in the furnace (40 F per hour) to about 1000 , after which cooling rate may be increased. Suitable precautions must be taken to prevent excessive carburization or decarburization. STRESS RELIEVING: When desirable to relieve the strains of machining, heat slowly to -1250& , allow to equalize, and then cool in still air (Strain Relieving). PREHEAT PRIOR TO HARDENING: Preheat slowly to 1350 and hold at this temperature until material is uniformly heated. HARDENING:After thorough preheating, heat to . Hold the work piece at the hardening temperature until it is completely and uniformly heated. QUENCHING: D2 steel is an air hardening steel and will develop hardness on cooling in still air. To avoid scaling and prevent decarburization of the work piece surface, controlled atmosphere or vacuum furnaces are recommended. If these furnaces are not available, pack hardening, salt baths or wrapping the piece in stainless steel foil will provide some degree of surface protection in the hardening process. Parts should be allowed to cool to 150F, or to where they can be held in the bare hand, and then temper immediately. TEMPERING: The tempering temperature may be varied according to the desired hardness. If maximum hardness is desired, tempering should be in the range , but if a lower hardness is acceptable, tempering at F will give the optimum combination of hardness and toughness. standard AISI, ASTM, BS, DIN, GB, JIS Size 5-1800mm weight and dimensions according to customer
Applications: cutting tools, blanking and stamping dies , thread cutting tools, machine knives for the wood paper and metal working Industries, broaches, measuring tools, plastic moulds. Steel grade: Gb 9crwmn C Si Mn P S Cr W 0.85~0.95 0.40 0.90~1.20 0.035 0.035 0.50~0.80 0.50~0.80 Din- 1.2510 %: C Si Mn P S Cr W 0, 90 - 1, 05 0, 15 - 0, 35 1, 00 - 1, 20 0, 035 0, 035 0, 50 - 0, 70 0, 50 - 0, 70 Similar grade: aisi-o1, sks3, k460 , din 1.2510 Delivery condition: Gb/t1299-2000 Din Aisi Annealed (hb) 197~241
Introduction AISI A2 Cold Work Tool Steel air hardening, with maximum dimensional stability during heat treatment, offering high abrasion resistance and good toughness. Generally supplied annealed to HB 231 max. A2 steel is an air hardening, cold work, tool steel. A 5% Chromium steel which provides high hardness after heat treatment with good dimensional stability. It is heat treatable and will offer a hardness in the range 57-62 HRC. Applications AISI A2 steel takes a place in tool steel range between AISI O1 and AISI D2, offering an excellent combination of good wear resistance and toughness. It may be regarded, therefore, as a ¡¡ãuniversal¡¡À cold work steel. For cutting operations the good toughness of AISI A2 gives excellent resistance to chipping of the cutting edge. In many cases tools made from this steel have given better tooling economy than high-carbon, high-chromium steels of the D3/W.-Nr. 2080 type. AISI A2 steel has much better machining and grinding properties.It can be used to make Bending Dies, Blanking Dies, Block Gauges, Cams, Coining Dies, Cold Forming Dies, Cold Shears, Cold Trimming Dies, Forming Dies, Knurls, Machine Parts, Mandrels, Plastic Mold Dies, Punch Plates, Punchers, Reamers, Ring Gauges, Roll Threading Dies, Rolls, Shear Blades, Slitters, Stamping Dies, Threading Taps, Trimming Dies, etc. HEAT TREATMENT Forging: Heat slowly toC then more rapidly to 1050-1100 Avoid working below . Reheat as often as necessary to maintain proper forging temperature. After forging cool very slowly. Heat slowly and uniformly. Cool in vermiculite or in other insulating media. Anneal after forging. Annealing: Soak thoroughly at then slow furnace cool at a rate of not more than 20C per hour. After annealing A2 a maximum hardness of 215 Brinell may be achieved.Protect against surface decarburization using controlled atmosphere or by pack-annealing. Hardening: Pre heat slowly to 600-700and soak. Continue heating to the final hardening temperature of 950/980 and allow the component to equalise. Quench in oil or cool in air.Temper immediately after hardening. Allow to cool to 125-F before tempering. Soak time is 15 minutes per inch of thickness. Minimum of 30 minutes. Tempering: Heat uniformly and thoroughly to the desired temperature and hold for 25 minutes per cm of thickness. A2 can be double tempering, after intermediate cooling to room temperature. Temper at 200C for a balance of hardness and strength or where strength is more important than hardness.Complete equalization of temperature throughout the tools is essential for good results. Double temper. Recommended temperature is 400-1000 hot rolled and hot forged according to the customer
We are the professional manufacturer of bimetal strips , hacksaw blade and power saw blade . Our main products see the following: 1.Bimetal steel strips for producing bimetal hacksaw blade , power saw blade , jig saw blade , band saw blade . 2.Best flexible bimetal hacksaw blade . 3.Hss all hard hacksaw blade 4.Flexible carbon steel hacksaw blade 5.All hard carbon steel hacksaw blade 6.Power saw blade from 300mm-750mm 100pcs/box, 2000pcs/ctn, or 144pcs/box, 1440pcs/ctn.
Flexible double edge hacksaw blade 1.High quality high carbon steel as material 2.Double edge and single edge3.With good and steady quality Size :12"x1" 12"x1/2" Packing:144pcs/box, 1440pcs/ctn or 100pcs/box, 2000pcs/ctn 144pcs/box, 1440pcs/ctn, or 100pcs/box, 2000pcs/ctn.
Flexible high carbon steel hacksaw blade High quality high carbon steel as material ,high frequency heat treatment to ensure the steady quality and endurance . size :12"x1" 12"x1/2" Packing:144pcs/box,1440pcs/ctn or 100pcs/box,2000pcs/ctn 72pcs/box,720pcs/ctn or 50pcs/box,1000pcs/ctn LISA FU (Mobile:0086-15854181028) 72pcs/box, 720pcs/ctn, 50pcs/box, 1000pcs/ctn.
Material: m2 high speed steel for teeth, 6150 or d6a for saw blade back Features: incomparably sharp saw teeth, cutting stainless steel and mold steel easily, unbreakable in cutting, service life over 100 times as long as ordinary carbon steel blades 100pcs/plastic box, 1000pcs/ctn or as customer's request
We are the professional manufacturer and reliable supplier of bi-metal strips , hacksaw blade £¬power saw blade ect . Our main products please see the following: £¨1£©bimetal strips for producing hacksaw blade , jig saw blade , power saw blade and band saw blade . (2)best flexible bi-metal hacksaw blade (3) high speed steel hacksaw blade (4) safety flexible high carbon steel hacksaw blade (single edge and double edges) (5) all hard carbon steel hacksaw blade (natural color , painted color and black blades) (6) hss power saw blade:size from 12"-30" 10pcs/plastic box, 100pcs/ctn.
A commonly used material, qualified quality, reasonable price, Quick service. 1.Electric furnace and electro - slag steel 2.We can make large - sized materials. 3.The factory has got more than 10 years production experience Specification Round bars dia 50mm-340mm length 14000mm Flat steel thickness 20mm-300mm width 1600mm length 13500mm Hot work mold steel (forging) The similar grades of Foreign countries Gb 4cr5mosiv1 Aisi H13 Jis Skd61 Din 1.2344 Ks Chemical Composition (gb) % C Cr Si Mo V Mn P S 0.32-0.42 4.75-5.50 0.80-1.20 1.10-1.75 0.80-1.20 0.20-0.50 Performance H13 die steel has excellent heat strength and hardness, high abrasive resistance and toughness, good hardening properties; high dimensional stability at heat treatment, also pretty good property of resistance to cold and hot fatigue. Applications Used for making hot squeezing mould, forging mould, hot extrusion dies, heat-resistant steel . Nude packing or packed with steel wires
Specifications Din 1.2316/420/s136h plastic mould steel 1.Rolled/forged 2.Iso9001:2008 3.100% ut 4.T:12-600mm w:100-1200mm l:2.0-5.8m Detailed product description 1. Plastic mould steel s136h/din 1.2316/aisi 420/3cr17nimnmo 2. Chemical composition: C Si Mn Cr S/p Mo Ni 4. Regular specifications: Rolled flat steel (thickness*width*length) mm Hot-rolled round steel (diameter*length) mm 12-70x155-610*2000-6000mm Dia:12-300mm*2000-6000mm Forged flat steel ( thickness*width*length) mm Forged round steel (diameter*length) mm 35-500*50-1200*2000-6000mm Dia: 50-500mm*2000-6000mm 5. Application: used for plastic mould which needs anti-corrosion and mirror polishing. 6. Payment: l/c at sight or t/t. Unpacked or according to the customers' requested
Specifications Large stock Competitive price Good quality 1, grade:cold work mould steel(d2/din1.2379/cr12mov1). 2, specification:dimension:20-500mm*50-1200mm. 3, chemical composition: C=1.40~1.60, mn=0.30~0.50, si=0.30-0.50, s 0.025, cr=11.0~13.0, mo=0.70~1.20, v 0.08 4, annealed hardness:hbs=207-255 5, application:used for various high precision, long-life cold work mould and tool, like:punching mould could squeezing mould. 6.Payment terms:30% t/t deposit in advance Unpacking or customized packing
Item Manual sealless steel strapping tool hp-35 Application Take advantage of sealless, powerless, flexibility, widely applied By manufacturing, metallurgy, transportation industries, such as steel Rolling, cargo transporting, hardware, equipment. Features 1. Handy light weight sealless combination tool to strap flat packages (i.E. Pallets, bales, crates, cases, various packages) 2. Permits a very easy and efficient operation and outperforms other Strapping tools by its ruggedness and its high reliability 3. The sealless joint reduces the overall strapping costs by approx. 10% through the elimination of the seals 4. Heavy duty and large tightening force, easily wrap & strap the heavy Package such as steel, aluminum bars. 5. Equipment with long life durance, whole tool & spare parts made From alloys with high strength, high durability, developed craft technology. 6. Patent design, safe & free fatigue. Type no. Hp-35 Strap size Width 12.7-19mm(adjustable) Thickness 0.38-0.7mm Strap material Steel strap Joint type Sealless Weight 3.9 kg Sealing strength 70%-80% Size Tools Weight 3.9 kg Sealing strength 70%-80% Size
9"x6mmx11"x4wire
Autel maxidas ds708 is obd2repair automotive diagnostic system.Maxidas ds708 support extensive vehicle coverage for more than 30 domestic, asian and european vehicle makes.Autel ds708 scanner work on wifi internet for wireless access throughout the workshop. Autel maxidas ds708 autel ds708 scanner Autel maxidas ds708 (pro) garage automotive diagnostic scan tool Update: free update by internet! The software about autel maxidas ds708: 1.8g(size), it is very powerful car diagnostic system Autel maxidas ds708 automotive diagnostic system is obd2 repair multi language obd diagnostic tool support english espanol france, deutsch, traditional chinese, simplified chinese, japanese, polish, portugal, korean, russian......Upating...
Engine type:air cooling single cylinder, 2 stroke Displacement:52cc Power:2.1kw Fuel mixture ratio:25:1(gasoline 25:twocycle oil 1 ) Fuel tank capacity:550ml Oil tank capacity:260ml Guide bar:16"/18"/ 20" Weight:8.2kg Meas:510*280*310mm
This product is made of high grade hard metal due to which it is very durable and posess high strength.
Engine model:gx35 Engine type: air cooling single cylinder, 4 stroke Displacement:38cc Rated power output:0.75kw/8000rpm Idling speed:2800-3200rpm Fuel mixture ratio:25:1(gasoline 25: two-cycle oil 1) Fuel tank capacity:1250ml. Pipe diameter:28mm Shaft length:1600mm Weight:7.6kg Meas:engine 270*260*360mm Shaft 1610*120*110mm
