YIHUA 8509 Micro Hot Air Gun Soldering Station with 3.5/3/2.5/2 mm Nozzle Temperature Adjustable SMD Rework Station Welding Tools. Feature: 1: Unique micro nozzles: 4mm nozzles ,3.5mm nozzle, 3mm nozzle, 2.5mm nozzle, 2mm nozzle, 1.5mm nozzle 2: Low noise design: When in max air volume, the noise from detector is less than 60DB, similar to normal indoor conversation sound. 3: Automatically cool-down function: In automatic mode, temperature will cool down to 100 when hot air handle is put in the holder because holder is equipped with an automatic sensor. When in manual mode,this automatic function will be stopped. 4: Rotatable display screen.It is convenient to adjust the display screen position via slight press 5 conversion function. 6. Temperature correction funtion. 7.Air gun auto. And manual conversion function Attention Please remove the screw at the bottom before use
ICC Pro will let you diagnose an or an with the Tristar/Hydra USB Controller IC and determine the source of the problem in a matter of seconds.The tool can test Lightning Flex, Tristar/Hydra IC, as well as VCC MAIN main power line for problems.ICC Pro will save you time and simplify the diagnostic process, allowing you to use your time efficiently. Feature: Identify the point of failure. Quick and easy: With the help of our ICC PRO you will save a lot of time and, as a consequence, money as well! It takes only a few seconds to run the tests, the tests can even be run right in front of the customer, enabling the technician to provide accurate diagnostic information and estimated repair price in a matter of seconds, be it a problem with a charging port, a chip or a short circuit on the main power line. Instant Test: As soon as the device starts, it performs a quick USB-Controller IC test. Should the IC be badly damaged and have significant internal shorts, you will be immediately notified, and no further tests will be performed. Dock Flex Test: This test checks the charging port flex cable for continuity. If any breaks in the lines are detected, you will be notified, and the names of the failed lines will also be provided to you. If the Dock Flex Test fails, no further tests will be performed. IC Test: Includes not only the test of 6 lines going straight to the USB-Controller IC, but also the PP5V0_USB, which goes directly (but not only) to Tigris. In case of any failure during this test, you will be notified accordingly, and the names of the lines that failed the test will be provided as well. In this case the next test will not be performed. Additional Test/VCC_MAIN Test: The lastAdditional Test checks the integrity of the power/charging system and can identify a short circuit on the main power line. In case problems are detected, you will see the Check VCC MAIN message on the screen.
Universal Battery Charging Activation Board Tester Fast Charging Plate For Phone Package including: 1pcs x Mother Charging Activation Plate 4pcs x Single Charging Activation Boards 1pcs x Red/Black Power Cable 2pcs x Micro USB Cables Features: Exclusive initiative motherboard design ,suitable for most of mobile model and pad model Battery fully charger can turn automatically-power off, to prevent overcharging Dual Displays: current display, voltage display Load voltage and current display Automatic recognition of battery positive and negative Automatic internal adjustment of the voltage and current display module Exclusive initiative battery discharge function Enhanced USB upgrade expansion design Can connect to the Power supply with 2A USB, also can connect the smart charger Quick charge and smart charge distinction A number of utility model patents and exterior design patents
JCID CT02 PD charger detector for testing voltage current of USB-C fast charger. JC CT02 PD fast charger tester for monitoring charger voltage current in real time. USB-C power adapter voltage current testing tool. Features: 1. Support single detection or batch detection Apple PD charger(fast charger). 2. Support PD/QC protocol, detect voltage and current in real time. 3. Support set output voltage. 4. Support online update and upgrade.
POWER-Z KM003C 0-50V 0-6A Portable USB C Tester PD3.1QC5.0 Digital Voltmeter Ammeter Power Bank Tester. Power-z KM003C Portable USB-C Tester PD 3.1 QC 5.0 Digital Voltmeter Ammeter Power Bank detector,Brand New Chargerlab Power-z KM003C USB-C Tester PD3.1QC5.0 Digital Voltmeter Ammeter Power Bank Tester. Precautions: 1. The QR code manual will appear when you first open it, you can choose to skip it and "start using" directly. 2. The current firmware version is the test firmware, there are some minor bugs that do not affect the use, please forgive me. Some unfinished features and issues will be added and fixed in subsequent updates. 3. HID is a data interface, used to connect to the host computer and PC suite (for the time being only Windows). It can be used for 5V power supply during testing, which is more stable. 4. The official version of the manual will be updated synchronously with the official firmware. Quick Start: 1. Insert the Type-C port of the Power-Z into the charging port of the mobile phone 2. Insert the original charger into the C port at the bottom of the Power-Z 3. Turn on the power to start using, easily monitor charging voltage, current, power and other data
Mijing BTR-20 Battery Repair instrument Battery data corrector for Phone battery data Reading Writing Repair. Mijing BTR-20 battery corrector for reset Phone battery health, calibrate renovate Phone Battery Health. renew Phone Battery Cycle Data. Function: Support over-current protection and reverse connection protection Support automatic detection,activation and charging Support for Phone 8 to 13 battery data read and write Support single battery row (no cell) mode Support single machine,online operation Support unlimited function upgrades Support data cloud backup Features: Mijing battery repair instrument solve the for Phone 11,12,13 series battery encryption, replacement battery core can not correct the efficiency, circulation problems. The battery instrument features resetting Phone battery health, calibrating and renovating Phone Battery Health, renewing Phone Battery Cycle Data. The battery corrector supports PC online read /write. Single battery data supports cloud backup and read/write functions. Dynamic display of battery data, battery level, cycle index, battery health
QUICK 967 220V digital temperature soldering station anti-static Product Features : Imported from Japan, ceramic heater, tip and heating element with international brands together Handle special lightweight, suitable for prolonged use. Anti-static design, prevent static leakage and damage delicate SMD components. Fast heat up, the instantaneous temperature compensation, temperature control accurate, stable. Special temperature locking device, prevent staff hackneyed temperature. QUICK 967 ESD built-in advanced micro-computer, digital adjustment and temperature display. Especially suitable for manual placement of SMD components, the rework and ordinary line components, welding, and other welding work for different process requirements. Product Specification : Model: Quick 967ESD Power: 60W Input voltage: AC 220V Temperature control range: 200 C-480 C Temperature stability: ±1 C Tip-to-ground impedance:
QUICK 203 soldering station is especially suitable for manual placement of SMD components, repair and welding of the ordinary in-line components, especially higher level of lead-free products, higher quality welding work. Quick 203 digital temperature soldering station Lead Product Features : Designed for lead-free soldering design Astonishing rate of temperature increase, the mixture was increased from room temperature to 300 �° C never exceeds 20 seconds. Intelligent perfect welding, plenty of power and change, depending on the size of solder joints, then solder joints be able to complete a perfect welding, can effectively prevent cold welding caused not firmly connected. Extraordinary heat recovery skills, the magic temperature compensation speed can solve the contradictions of temperature lead-free soldering process, lead-free soldering tool, an indispensable tool for certain low temperature conditions welding. Extend tip life, welding relatively lower temperature greatly extend the life of the tip. Performance Parameters : Temperature adjustment range: 50C -600C Temperature stability (no load): ± 2C Input voltage, frequency: 220V/110V 50Hz/60Hz Output voltage, frequency: 36VAC 400KHz Maximum power: 60W Heating time: (20C -350C) The temperature dropped from: 30C Tip-to-ground resistance:
ChargerLAB POWER-Z MF003 Apple PD Charger Tester Charging Head Network Tester, MF003 POWER-Z PD Charger Tester Charging Head Network Tester Voltage Current Detection. If the tester does not respond when connected to the computer, check the following steps: 1. Check whether the connected interface is correct; 2. Replace the cable, some cables have no data transmission function, 3. Replace the USB port. 4. Replace the computer, the software only supports Windows10, not other operating systems. Description: 1. The ChargerLAB POWER-Z MF003 main housing part of ChargerLAB POWER-Z MF003 is made of a single piece of aluminum alloy and is made by one-piece molding process. 2. Currently, only current less than 3A is supported during power measurement. Built in 1020mAh battery is convenient for immediate use, and an indicator light is on when charging. 3. The large-screen display can show users more and more complete products. On the side, there are the charging status indicator, three function selection buttons, and the USB-C input interface. 4. On the top of the POWER-Z MF003 are a switch, a buzzer and a Micro USB port, which can be used to charge the device or connect to a computer for firmware update. 5. There is a port for light on the button and one Type-C port on the side.
BAKU 601D LED Digital Display Hot Air SMD Rework Station, Soldering Iron Heat Gun Kit 2 in 1 for BGA Phone Welding Repair. Features: 1. Small Size. Save working space. 2. Hot Air Rework Station and Soldering Station 2 in 1. 3. Soldering station and heat gun are used microprocessor PID temperature regulation. 4. The system has automatic cold function. When it s cooled to 100 degree Celsius, it will be power-saving mode automatically. 5. This helps to extend the heating units life and protect hot air heat gun. Attention: Be careful when operate with high temperature. Do not use it near to the flammable and explosive gas and objects. The air outlet is really hot that can burn body. When the hot air gun is working, please do not leave your position. Do not touch the hot air gun by children. After using be sure to cool down the machine and put it in safety place. When it s turn off, the heating tube will gush out cool air temporarily. During cooling time please do not take out the power plug.
iFace is only a matrix tester not a programmer, it doesn't fix face ID issue or do any program work, so It only for the ones who do massive Face ID repair or testing work. Note: it can t unlock faceID iFace Matrix Tester dot projector tester: to test move a little higher and move a little lower. Support X/XS/Xr/Xsmax,/11Pro and some Pad
JC Dot Matrix Detection Module For phone pad Face Testing Repair.Support: X-11Pro Max Pad A12X Support to check if the face dot matrix is normal, and the functions like fuse,NTC disconnected, I2C disconnected, short circuit etc. Support dot matrix encrypted data read & backup, the burning function will be opened in future. Need Connect with 1000s to use repair the dot matrix face inaccurate positioning problem. The original chip encrypted data needs to be read.
LB Dot Matrix Tester Fix phone Face ID Not Working On X-12 Pro Max. read the data of Dot projector, Support: X-12Pro Max / Pad A12X, LB Dot Matrix tester Fix phone Face ID Not working on X-12 pro max. Support dot matrix encrypted data read & backup, the burning function will be opened in future. Support to check if the face dot matrix is normal, and the functions like fuse,NTC disconnected, I2C disconnected,short circuit etc.
Mijing Dot Matrix Face ID Repair Holder Fixture, Support phone X-11 pro max Lattice Repair, MJ Front Facing Camera Repair Fixture for Fix Face ID not working.
WL tin planting Steel Mesh For Phone Face ID / dot matrix / original color / tail plug small plate tinned steel mesh, Precise hole position enough tin planting.Accurate positioning, al-tin planting, one-time molding non-tin adhesion, non-tin connection, easy to disconnect Steel mesh material: steel Product name: ip x-11pro maximum Face ID /dot matrix/original color/tail plug small plate tinned steel mesh Features: not easy to deform, prevent heating and bulging accurate hole position, one-time molding Applicable models: X-XR-XS- XS MAX-11-11PRO-11PRO MAX Stand by XR-XS-XS MAX 11-11PRO-11PRO MAX Surface dot matrix original color 11pro tail plug small plate planting tin Good toughness, high temperature resistance, Heated anti-drum design Planting tin is more suitable with continuous bending and full of toughness Note: The manual measurement is wrong the actual size is subject to the actual product
JC Dot Matrix cable for Phone X-13 Pro Max Face ID repair. JC Dot Matrix Flex Cable is used to repair Phone Face ID lower/higher issues. JC dot projector lattice IC chip for Phone 13/13Pro/13 Pro Max/13 mini face ID repair. JC Dot projector flex cable used with JC Pro1000s Dot Matrix Module or JC V1S dot projector board. JC Face ID Dot Flex Cable For Phone X/XS/XS MAX/11/11PRO/11 Pro Max/12/12Pro/12 Pro Max/12 Mini/13/13Pro/13 Pro Max/13 mini. JC dot matrix flex cable full set 13pcs(X-13 Pro Max): 1x JC dot matrix flex cable for Phone X. 1x JC dot matrix flex cable for Phone XS. 1x JC dot matrix flex cable for Phone XS MAX. 1x JC dot matrix flex cable for Phone XR. 1x JC dot matrix flex cable for Phone 11. 1x JC dot matrix flex cable for Phone 11 Pro. 1x JC dot matrix flex cable for Phone 11 Pro Max. 1x JC dot matrix flex cable for Phone 12/12 Pro. 1x JC dot matrix flex cable for Phone 12 Pro Max. 1x JC dot matrix flex cable for Phone 12 Mini. 1x JC dot matrix flex cable for Phone 13. 1x JC dot matrix flex cable for Phone 13 mini. 1x JC dot matrix flex cable for Phone 13 Pro/13 Pro Max. Tools required: JC Face lattice detection module (JC Dot Matrix Module) JC Pro1000s, or JC V1S V1S dot projector board.
"brush cutter blade size :255*25.4*40T thickness:1.25MM MATERIAL:IRON Function :cut grass"
"brush cutter blade size :255*3T*3.0*25.4 thickness:1.6MM MATERIAL:IRON Function :cut grass"
"Suitable for most leading trimmers and brushcutters. Longer lasting trimmer line than normal line. Premium trimmer line for cutting."
*Gasoline/2-cycle oil mixing ratio: 25;1 * Oil tank capacity: 260ML * Fuel tank capacity: 550ML * Displacement: 58cc * Engine type: 2-stroke,air-cooling *POWER MOTOR: 2.6 KW *PRODUCT COLOR : Red+Black * CE Standard
