Shoe primer, hardner and adhesive, hot melt glues.
Coated steel: hot dip galvanized steel/galvalume steel/galfan (hot rolled, cold rolled) , pre painted gavlanized steel, galvalume steel/ galfan steel, electro galvanized steel stainless steel coil/ strips/ sheets/ plates: 200, 300, 400 series.
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
DESCRIPTION Bituminous Primer is product containing oxidized bitumen and a mix of technical quick drying solvents. APPLICATION Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness. INSTRUCTIONS FOR USE Concrete surfaces must be dry, clean and free from oil, dust or release agents. This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment. Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces. PACKING 5 gallon Bucket SHELF LIFE The product can be stocked in closed buckets and in dry area, far from UV rays for 12 months. TOOL CLEANING After use clean tools with common solvents.
DESCRIPTION CC-600SP is a two component, solvent-free epoxy system with high chemical resistance and high bond strength. The epoxy may be applied as a primer for most high end industrial coatings, like Epoxies, PU. CHARATERISTIC Easy apply Low odor High bond strength Abrasion resistant Chemical resistant APPLICATION Concrete coating Cement
Description HY-330 contains specific high content of polymer resin, and can use with difference size of quartz sand to lay out sand texture. It is non-toxic, eco-friendly, and can be applied on both interior and exterior wall, help enriching the monotonous surface. Use 1.Interior and exterior wall decoration. 2.Enhance the finish surface by texturizing molding. 3.Other decoration usage. Feature 1.Water-based, eco-friendly, and non-toxic. 2.Tough, durable, with good weather resistance. 3.Can prevent surface chalking of cement. Series Product HY-360/ Stone Plate Texture Coating
CA-010P as a water-based primer in relation to water absorption reduction and increase the bonding strength of cement to reinforcements other than being used as admixtures increase the mechanical properties and the adhesion of the hardened material. AREA OF APPLICATIONS Repair mortar for concrete areas Industrial flooring Bonding agent for new to old concrete Enhance adhesion strength of mortar
Feature: Reinforcement of Waterproof High heat insulation Good quality and dust resistance Water resistance and high weather durable. Drying faster and easy application. Application Cement wall Galvanized steel Color pre-painted steel Plywood Plastic wave-board Lime-wall The coverage will be affected by substrate dimension and application method. The loss factor as follow - Brush= Theory coverage X1.4 Spray= Theory coverage X1.7
Strict quality control starts from the beginning with processing of first-class raw materials by adopting advanced facilities to make quality products. We serve our industrial customers directly, provide not only professional technical support but also cost-effectively products and services
Strict quality control starts from the beginning with processing of first-class raw materials by adopting advanced facilities to make quality products. We serve our industrial customers directly, provide not only professional technical support but also cost-effectively products and services
DESCRIPTION CC-604SP is two component water based epoxy primer, composed from water based of liquid epoxy resin and hardener. APPLICATION 1. To prime the surface and help the following application procedure to mold and decorative coating. 2. Highly resist to chemicals in non-circulated places. 3. With well adhesion ability with epoxy system or PU system application. 4. Suitable for hospital, operation room, food factory to prevent the mold, dust and bacterium. CHARATERISTIC 1. Able to be diluted by water. 2. Anti- efflorescence , suitable for the environment with highly hygienic request. 3. Good adhesion to the moisture surface, can take as the primer for solvent-free or solvent-based epoxy resin.
1>. A5 size with 6-holes colored binder. 2>. Dimension of cover is 17.50 X 23.0 CM. Dimension of refill is 14.20 X 20.70 CM. 3>. The color of 6-hole binder is by plating not by spray paint. So, the color look more vivid as well as more durable. Color looks dull and easy to fade away if by spray. 4>. Color of the PU can be matched with the binder. 5>. The internal design/layout and the tab can be customized by the customer. 6>. We have at least more than thousands of colored changing PU in stock . So, customer could select color combination without considering the MOQ of the PU. For example, 1,000 PCS for 2 colors or 2,000 PCS for 4 colors. Low purchasing threshold of the material allows customers more flexibly design the color combination and diversify the market.
These products can be applied onto safety signs, bicycle, motorcycle, automobile and indoor/out door decoration. Application: 1.Public emergency exit, safety exit. 2.Home safety assistance: power switch, flash lights, stairs, door knob 3.Outdoor activities equipments: helmet, tent, raincoat, etc 4.Autos: bicycle, motorcycle, auto body pattern, aluminum ring, steel ring. Volume: 140ml Packaging: 12 cans/box Color: green, yellow, red, blue, semi-transparent olivine and blue.
DESCRIPTION CC-404 is a two component, high performance, pre filled epoxy grout , suitable for use as a pourable or fluid grouting material. Aftek F4 and F6 fillers may be added to produce a trowellable high build mortar or a pourable flowable grout. FEATURES â?? High flow properties â?? Bonds to damp substrates â?? Rapid hardening and strength gain â?? High chemical resistance â?? Pre-measured kits make for ease of use â?? High tensile and compressive strength â?? 100% solid epoxy â?? Excellent adhesion to most substrates â?? Cures at temperatures down to 5oC â?? Negligible shrinkage â?? High mechanical strength â?? Solvent free High early strength PACKAGING CC-404 is available in 3 litre and 15 litre kits
Pass rohs standard, environmental formula paint. Can be applied onto wood, metal, acrylic, styrofoam, plastics (pe & pp are not allowed) products and other items. Can be clean with water before it dry. After dry, can be clean only with alcohol. Safe for children to use. Coverage : 0.9~1.5m2 (2 rounds of spray) 24pcs/ctn
Super wool roller covers, best paint pick-up and best paint release. **any sizes (4", 7" or 9"...Etc.) available, Any nap legth of fiber (3/8", 1/2"..Etc.) Available, Us. Type or european type available. Each pc printing polybag, 60pcs each carton
Model no.: tensky Made in taiwan, roc Key features This product complies with the eu rohs directive. The high-tech nano paint achieves energy conservation and environmental protection by converting heat into energy when it is applied to the mechanical cooling systems and fuel systems.
Paints.
Our multi-functional universal color paste is compatible with full range of resins (such as ALKYDíBACRYLICíBPOLYESTERíBEPOXYíKíKíK) to make full range of colored coatings ( such as PU COATINGíBNC COATINGíBBAKING COATINGíBEPOXY COATINGíKíKíK), and it can be extended to produce colored coatings of any systems.
Chaoh Shinn provides various kinds of low toxic,high quality and price- competitive thinners in accordance with customers' operating conditions-temperatures, humidity and any other special requirements respectively.These solutions will enable our industrial customers to manufacture high quality products and make benefits due to more productivity as well as cost savings in purchasing, inspection and production.
