Transformer bobbins Injected phenolic material and inserted pins 39x34x29cm about 9kgs
Transformer bobbins Made from Phenolic, PBT, Rynite or Nylin
Model Number 35 39 42 57 86 110 Length/Side (mm) Height (mm) Step Angle (deg.) 0.9 /1.8 Drive Voltage (v) Rated Current/Phase (ma) Winding Resistance (Ohm)
Item T1011N 1. Rated Voltage (V) DC 5 2. Rated Current/Phase (mA/RMS) 111 3. Coil DC Resistance (Ohm) 45 10% 4. Step Angle (Degree) 18 5. Drive Mode Constant Voltage 6. Excitation Method 2-2 Phase excitation(Bipolar driving) 7. Insulation Class Class E 8. Pull-out Torque (g-cm/pps) 5.9/500 9. Pull-in Torque (g-cm/pps) 5.6 /500 10. Max. Pull-out Pulse Rate (pps) 1310 11. Max. Pull-in Pulse Rate (pps) 1160
Stator : OD140(NEMA48) Input Power : VAC 115/230 output power : 1HP Speed : 300 ~4000 R.P.M Rotation : CW CCW Magnet : Permanent magnet Bearing : Ball bearing Storage humidity : 95%RH max. (non condensing) Operation temp. : 0-55(non condensing & freezing) Insulation class : B Energy efficiency : 1st level
Stator : OD120(NEMA42) Shaft : Single Dual Input Power : VAC 115/230/277 output power : 1/4 HP, 1/3HP Speed : 300 ~4000 R.P.M Rotation : CW CCW Magnet : Permanent magnet Bearing : Ball bearing Storage humidity : 95%RH max. (non condensing) Operation temp. : 0-55(non condensing & freezing) Insulation class : B Energy efficiency : 1st level
Stator OD94 Shaft Single dual Input power : DC24/48V or DC115/310V output power : 20~250W Speed : 300 ~3000 R.P.M Rotation : CW or CCW Magnet : Permanent magnet Bearing : Ball bearing Storage humidity : 70%RH max. (non condensing) Operation temp. : 0 40 non condensing and freezing) Insulation class : E Energy efficiency : 1st level
Stator : OD82 Shaft : Single Dual Input power : DC24/48V DC115/310V output power : 20~250W Speed : 300 ~3000 R.P.M Rotation : CW CCW Magnet : Permanent magnet Bearing : Ball bearing Storage humidity : 70%RH max. (non condensing) Operation temp. : 0 40 (non condensing & freezing) Insulation class : E Energy efficiency : 1st level
Shaft : Single Rated voltage : DC 24V Input power : 20W Revolution per minutes : Max 1350 R.P.M. Rotation : CW/CCW Magnet : Permanent magnet Bearing : Ball Bearing Storage temperature : 5~95% RH Operation temperature : 0-55 Insulation grade : E Energy efficiency : The first level
High Efficency Power Supply
DC Brushless Motor Application
Arcing is eliminated. Connect the red battery clamp to the positive battery terminal. Connect the black Clamp to the negative or ground to a rigid metallic surface on the engine. The connection should be 12 to 19 inches from the battery. 4.Hose: Since the pump has a lower discharge pressure it is ., recommended that anoncolapsiable hose be used for maximum pumping capacity. 5.Hoisting & lowering: Use the attached nylon line. Do not use the power cord ., for handling the unit. 6.Operation of unit: Lower the unit into the liquid to be pumped(note: this unit is not to used to pump Flamable liquids).Then turn on the switch. Pump can be run for a few minutes(less than 5) without liquid. Do not run completely dry for any extended period(less than 5 min.).This will prevent. 7.Running time peroids: The unit draws 20-25 amperes and can be operated for approximately 1 hr. On a fully charged 60 amp-hour battery and still be able to start the vehicle under normal conditions. Caution should be used when running times exceeds 25 !v 30 minutes without the engine running to recharge the battery. Also be mindful of cold temperatures which lowers battery
Spe3 series 1/3 hp effluent pumps 1.1/2" solids handling 2.Heavy duty lip & mechanical seals in tandem 3.115 & 230 volts available 4.60hz 5.Durable cast iron motor housing 6.115 & 230 volt piggyback power plug and switch Plug w/20' cord as standard
Dsgp1-2021-60hz Dsgp1-2023-60hz 2 hp grinder pump 1.Double mechanical seal 2.Silicon carbide (main) !v grit 3.Resistant 4.Carbon ceramic (secondary) 5.Dual sealing chambers with 6.Moisture detection for optimum 7.Motor protection ductile iron 8.Impeller, recessed, clog-free 9.30 year proven design 10.Stainless steel grinder assembly 11.Effectively macerates domestic 12.Into a fine slurry
Dshhgp1-2021-60hz 2 hp grinder pump 1.Ideal for long discharge runs or high static heads 2.2 piece motor housing 3.Separate cord cap assembly 4.Internal capacitors - no control box req'd ductile iron impeller, recessed, clog-free dual silicon carbide seal - grit resistant stainless steel grinder assembly effectively macerates domestic sewage into a fine slurry 5.30 year proven design
Digp-7023/7043-60hz (patented) 1.Available with 2.7.5 hp grinder pump 3.High head, double stage 4.Doubled output pressure 5.Unmatched performance 6.350 shut-off head 7.Flows to 100 gpm 8.Balanced design 9.Ideal for long discharge runs or high static 10.Heads 11.Potentially replaces higher hp pumps 12.Ductile iron impeller, recessed, clog-free 13.Silicon carbide seals !v grit resistant
We are professional motor manufacturer and earned much reputation in the treadmill motor field. Our products range cover from ac induction, pmdc, a/dc universal, low voltage battery, gear reduced and customized motors. General export cartons.
Headlamp leveling motor. 1pc In 1 Bubble Wrap ,100pcs In 1 Outer CTN.
Diffuser is designed for matching with the ready made local 4/8" faucet, easy to install. Tough and durable construction. Higher oxygen dissolution rate and corrosion resistance. Prevent backflow and clogging. Material: 1. Diffuser cover:neoprene rubber, resisting against acid and alkali. 2. Diffuser base:abs Specifications: 1. Bore:4/8'' - thread, 3/8'' - air inlet. 2. Diameter:80mm 3. Height:40mm 4. Ventilation volume:0.08 ~ 0.10 m¦/min -
Features: 1. Lower noise:pressure pluses are the major noise source in blowers. The trundean roots blower design can efficiently reduce noise by approximately 5 db. 2. Lower energy consumption:trundean roots blower are designed to control backflow pressure to the rotor in order to reduce energy consumption. 3. Longer bearing life:less vibration transmitted through the lobe results approximately 20% longer bearing life. -
