Technical Specifications: Vibro-feedhopper Volume: 3.5 m3 Pre-screening Grid Entry Opening: 1000x500 mm Outlet Opening: adjustable 45-100 mm. Capacity: max 80 tons/h 2 Units of Mechanic Collapsible Belt Conveyor Diesel Motor and Generator Control Panel Chassis: Tandem Axle, Air Brake, Taillights, Towing Eye It can be towed up to speed of 80 km/h on highway.
Pe series jaw crusher is widely used for primary crushing of hard rocks and block materials. It is widely used in chemical, mineral, quarry, building materials, road, railway and water conservancy and hydroelectric power industry. The large and medium-sized crushers are the key products of our company for their advantages of design and production. Working principle of jaw crusher: The motor transmits through belt, drives the movable jaw up and down by eccentric shaft. When the moving jaw plate rises, the angle between the fixed jaw plate and the movable jaw plate gets larger, and the materials can be crushed to reach the crushing target. When then moving jaw plate is down, the angel between the moving jaw plate and fixed jaw plate becomes smaller. The movable jaw plate leaves the fixed jaw plate under the effection of drawbar and spring, and then the crushed materials are discharged from the lower outlet of the crushing cavity. In bulk or container.
Working principle of impact crusher: When the impact crusher works, the motor drives the rotor rotate of the impact crusher with high speed, on the rotor where installed the hammers. When the materials get into the area which the hammers effect, under the impacting function of the hammer at a high speed, the materials are thrown to the impact device above the rotor continuously. And then the materials are rebounded from the impact liner to the area where the hammers effects for being refreshed. The materials from large size to small size, all of them can be crushed at the impact chamber repeatedly until the material are crushed to the required size and then discharged from outlet of the impact crusher Characteristics of impact crusher: Special structure, connected without key, high chrome hammer, unique impact liner, dealing with hard material, high efficiency and saving energy, cubic shape of product, adjustable output size. In bulk or container.
The hammer crusher (hammer mill) has good quality features like simple structure, high reduction ration, high efficiency, and etc. The pc hammer crusher (hammer mill) is suitable for both dry and wet crushing of brittle, medium-hard materials for the mining, cement, coal, metallurgic, construction material, road building, and petroleum & chemical industries. Operating principle of hammer crusher: The motor drives the rotor rotated of the hammer crusher at a high speed through the belt, and on the rotor there are series of hammers. When the materials get into the working chamber of hammers, they are crushed by the rotating hammers with high rotation speed, the products which are crushed to meet the required size can be discharged by the outlet and become the final products, while the large size products are brought back to the crushed area by the hammers for being recrushed until they reached the required size. In bulk or container.
The spring safety system works as an overloading protection system which allows metals to pass through the crushing chamber so as not to damage cone crusher. The safety system adopts dry oil and water as two kinds of sealed formation to make plaster powder and engine oil separated to ensure reliable performance. The crushing chambers are depending upon the feeding size and the fineness of final products. The standard type(pyb) is applied to medium crushing; the medium type is applied to medium or fine crushing; and short head type is applied to fine crushing. In bulk or container.
The series of 2-roller crusher can be applied in industrial sectors such as ore crushing ,chemical industry, cement, refractory, abrasive and construction industries to break ores and stones of high and medium rigidities, and particularly applied in the building material industry to produce pisolitr and pea gravel, which is with better effect than ordinary crushers. This series crusher has good characteristics like reliable working, simple maintenance, low operating cost and adjustable marking granularity. In bulk or container.
Vipeak Portable type series Mobile crusher have five type excellent mobile crusher: 1.Jaw Crusher type Mobile Crusher; 2.Impact Crusher type Mobile Crusher; 3.Cone Crusher type Mobile Crusher; 4.YGFS Various Combined Crusher type Mobile Crusher. 5. YG938E69 type mobile primary crushing station. All our Portable type series mobile crushers are developed according to novel series design idea of stone crushing equipment, which expands the concept field of coarse crushing and fine crushing. Its design idea is based on the requirements of clients, which clears faults of the crushing place, surroundings and the complex basic configurations. This series mobile crusher really supply simpler, higher efficient lower cost machines for clients. The excellent performance of portable type series Vipeak Mobile crusher: 1. High performance jaw crusher, impact crusher and cone crusher. 2. Feeder, belt conveyor and vibrating screen are all in one. 3. Turn axle of traction is convenient for road transit and expanding the working place. 4. Vehicle installational supporting is easier for equipment to station in the working place. 5. Vehicle electric generating set, motors and control box are all included. Applications and advantages of portable type series Mobile crusher Integrative equipment group: Flexibility of the mobile crusher; Lower freight cost; Direct and efficient operation; Easy to adapt and flexible to collocate; Reliable performance and convenient maintenance. Different Type match the different technical parameters. All of Vipeak products have been Certificated by CE ,ISO9001-2004, IQNET , GOST. Contains or other export standard. More Details will send you by mail in 24 hours after receive your enquiry.
Impact Crushers are used in both primary and secondary crushing applications of aggregate, and in recycle crushing of reinforced concrete, asphalt and other construction and debris. VIPEAK is a reliable supplier of Impact Crusher with new design. Working Principle of Impact Crusher: When the Impact Crusher works, the motor drives the rotor rotate of the Impact Crusher with high speed, on the rotor where installed the hammers. When the materials get into the area which the hammers affect, under the impact function of the hammer at a high speed, the materials are thrown to the impact device above the rotor continuously. And then the materials are rebounded from the impact liner to the area where the hammers effects for being re-crushed. The materials from large to small all to be crushed at the impact chamber repeatedly. The process won't stop till the material are crushed to the required size and then discharged from outlet of the Impact Crusher. Characteristics of Impact Crusher: Excellent cubic final products Special structure Non-key connection High chrome hammer Durability in long time simplicity in operation Easy adjustment, high reduction ration Good performance and high reliability Specification and Technical Parameter of Impact Crusher: Model Specification (mm) Feed Opening ( mm ) Max. Feeding Size ( mm ) Capacity ( t/h ) Power ( kw) Overall Dimensions (mm) (L¡ÁW¡ÁH) PF-1007 ¦µ 1000¡Á700 400¡Á730 300 35-50 37 2400¡Á1560¡Á2660 PF-1010 ¦µ 1000¡Á1050 400¡Á1080 350 50-80 75 2440¡Á2250¡Á2630 PF-1210 ¦µ 1250¡Á1050 400¡Á1080 350 70-120 110 2700¡Á2340¡Á2870 PF-1214 ¦µ 1250¡Á1400 400¡Á1430 350 80-160 132 2700¡Á2440¡Á2900 PF-1315 ¦µ 1300¡Á1500 860¡Á1520 500 160-260 200 2860¡Á2800¡Á3050
Vipeak YGM Type Raymond mill have four excellent advantages:1.Three-dimensional structure .2.Land-saving.3.The screen-passing rate can reach to 99% .4.The transmission is steady and reliable. With qualified products and good service, VIPEAK supplies series Raymond Roller Mill (Raymond Mill ), which is suitable for grinding barite, calcite, potash feldspar, talcum, marble, limestone, ceramics, etc. Working Principle of Raymond mill: First material should be crushed into the desired size by Jaw Crusher, and delivered to the Silo by Bucket Elevator. Our Designed Vibrating Feeder will feed the material into the grinding room. With the air current from the Air Blower, those powder conforms to the fineness degree will be blew into the cyclone collector and those powder that is not consistent with the desired size will return to the grinding room to be re-ground. The whole system is airtight circulation, and the circulatory flow under the negative pressure. Vipeak Raymond mill Model recommendation: 1.Model 3R2115£º Max Feeding Size (mm) :15 The final products size (mesh) :80-325 (finest 500) Capacity (T/H) 0.2-1.5 Rotational Speed of the Central Axis 160Rev The inner Diameter of Roller (mm) §¶630 The Diameter of Roller (mm) §¶210 Height of Roller and Ring (mm) 150 Motor of Mainframe Y200L-8-15KW Motor of Air Blower Y132M-4-11KW Motor of Separator Y112M-6-2.2KW Dimension (L¡ÁW¡ÁH) 4.6¡Á3.4¡Á5.9 . All of Vipeak products have been Certificated by CE ,ISO9001-2004, IQNET , GOST.
VSI Series Sand making machine (VSI Series Vertical Shaft Impact Crusher) is on the basis of our company¡¯s many year's research and development, manufacture of mining machinery as well as absorbing home and abroad advanced technology. It is the international advanced level of the new generation of energy-saving, efficient crusher. the performance in a variety of ores a chronology of equipment plays an irreplaceable role. The machine can be widely used in metal and non-metallic minerals, building materials, sand making, crushing and shaping of all kinds of metallurgical slag. It is suitable for brittle materials with Mohs hardness under nine, not suitable for viscous material and rock with much dirt. Vipeak VSI sand making machine Working Principle: In Centrifugal impact crusher, material of high speed is crushed by self-broken mutual friction. Centrifugal impact crusher can not only crush but also shape stones. According to feeding method, centrifugal impact crusher working form is divided into central feeding and central with cascade feeding. The crush form is divided into "rock on rock" and "rock on iron" According to material compressive strength, abradability. There are four working forms: central with cascade feeding "rock on rock" and rock on iron"; central feeding "rock on rock"and rock on iron". VSI Series Sand making machine Daily Maintenance: 1) There should be some person responsible for the machine. Operator should be trained. understand technical performance of the equipment, familiar with the rules. 2) To keep machine smooth running, draw out regulations of machine maintenance and safe operation. Meantime prepare necessary maintenance tools, lubrication material and other related equipments. 3) Check firmware every shift, fasten immediately if any flexible. 4) Stop the machine termly, open the checking door and check inside wear condition. Replace and remove immediately if any wear, werable block should be changed whole set if any wear to keep impeller balance in running. Replace or repair immediately if any wear on impeller. 5) Check impeller firmware every 7 days, wearable parts should be replaced and repaired if any wear. 6) Check firmware and wearable parts in whirlpool chamber every half a month, if any abnormal condition, take immediate means to remove. 7) Thin oil station use 35# bearing oil, oil amount is 150-190L. Change oil in 200hours first time, then change oil every 1000. when change oil, open the oil pipe, clean and dry it, change damaged seal mat. 8) Driving V belt tensioning is moderate, make sure v belt strain evenly, motors in two sides are imbalanced, the electricity current is not more than 15A. 9) Check hydraulic system frequently, maintain immediately if any abnormal phenomenon. 10) Add calcium base grease to seal ring under bearing chamber regularly. 11) Open the bearing tube and clean in 1000 hour's normal running first time. Power supply of the VSI sand making machine is AC380V,50Hz; Double motor power of VSI from 2*25 KW to 2*200 KW. The Weight of VSI from 10 to 25.6 tons. Range of Rotation speed is from 1180 r/min to 1890 r/min; Range of the Max. feeding size is 30-50 mm. All of Vipeak products have been Certificated by CE ,ISO9001-2004, IQNET , GOST.
Product introduction: SANYYO PE series jaw crushers are based on a forward-looking idea of making our users enjoy great variety-both casting and welded frame construction.The design offers owners the highest possible fatigue strength, excellent reliability and numerous mounting possibilities. This, combined with special high-quality cast steel components and very durable wear parts, means exceptionally high crusher availability, cost-efficient crushing and low cost per ton. Every SANYYO jaw crusher is a product of know-how and experience optimized by Finite Element Analysis (FEY). Each model is tested virtually for stress, strain, shock, deformation, thermal loading, vibration and noise under a wide range of load conditions. The result is exceptional reliability. Features and values • High reliability • both casting and welded frame construction • Top crushing performance • Wedge setting adjustment • Fast and simple maintenance • Easy and less costly to install • Excellent total crushing economy • Excellent suitability • Highly versatile: ready and able to crush all your tons. Nude packing & wooden case.
Natural stone
Portable Jaw Crusher plant provides a new field of business opportunities for contractors, quarry operators, recycling and mining applications. It offers high efficient and low cost project plan without environment limit for the client. 1000*500*1000.
Box Type Crusher is a one of new designed crushing equipments in our company, which has gather all virtue together from jaw crusher, hammer crusher, impact crusher. The box type crusher is the most advanced and practical stone equipment because of its automatic feeding and operation line, which has met with a favorable reception from customers. Range of Application: 1. Primary and secondary crushing of various materials lower the average hardniess. 2. Especially suitable for crushing of materials of mining, building, chemical industry and metallurgy.
This machine is good for your factory to produce cut-to-size. It has good quality and stable fast cutting. Parameter: Max.working dimensions(L,W,H) 3200,3200,160mm Max.diameter of blade 400 mm Table dimensions(L,W) 3200,2000 mm Table tilting degree 0-85 no Table rotating degree 360 no Main motor power 15 kw Water consumption 4 m3/h Overall dimensions(L,W,H) 6000,5000,2800 mm Power condition 380V,50HZ. Plastic fil & General Purpose Container.
Working principle of jaw crusher: The motor transmits through belt, drives the movable jaw up and down by eccentric shaft. When the moving jaw plate rises, the angle between the fixed jaw plate and the movable jaw plate gets larger, and the materials can be crushed to reach the crushing target. When then moving jaw plate is down, the angel between the moving jaw plate and fixed jaw plate becomes smaller. The movable jaw plate leaves the fixed jaw plate under the effection of drawbar and spring, and then the crushed materials are discharged from the lower outlet of the crushing cavity. Characteristics of jaw crusher: High crushing ratio, homogeneous final granularity size, simple structure, reliable working condition, easy maintenance, low operating cost and so on. In bulk or container.
Jaw crusher Product introduction SANYYON PE series jaw crushers are based on a forward-looking idea of making our users enjoy great variety-both casting and welded frame construction. The design offers owners the highest possible fatigue strength, excellent reliability and numerous mounting possibilities. This, combined with special high-quality cast steel components and very durable wear parts, means exceptionally high crusher availability, cost-efficient crushing and low cost per ton. Every SANYYO jaw crusher is a product of know-how and experience optimized by Finite Element Analysis (FEA). Each model is tested virtually for stress, strain, shock, deformation, thermal loading, vibration and noise under a wide range of load conditions. The result is exceptional reliability. Jaw crusher Features and values 1. High reliability 2. Both casting and welded frame construction 3. Top crushing performance 4. Wedge setting adjustment 5. Fast and simple maintenance 6. Easy and less costly to install 7. Excellent total crushing economy 8. Excellent suitability 9. Highly versatile: ready and able to crush all your tons 10. In stationary or semi-mobile installations.
Product introduction SANYYO PF Series impact crushers feature a unique combination of heavy-duty rotor, crushing chamber and wear material. Dealing with the material no more than 350Mpa anti-pressure strength, Impact Crusher can be widely used in the first and secondary crushing. During the process of operating, the rotor in high speed will be brought along by the electric motor. The material will be stricken by the Flat Hammer to be crushed, and then be countered to the liner for the second crushing, then be discharged through the discharge opening. Features and values 1. A wide range of application 2. Unique hammer attachment system for increasing security 3. Easy to operate and maintain 4. Wide range of hammer and liner materials, including manganese, martensitic, high chrome and ceramic insert .
Features and values 1. A wide range of application 2. Unique hammer attachment system for increasing security 3. Easy to operate and maintain 4. Wide range of hammer and liner materials, including manganese, martensitic, high chrome and ceramic insert 5. It is widely used in quarry, mining, construction, road building, highway and railway construction, Metallurgy and so on.
Raymond mill description: Application range: raymond mill is applied for the powder processing of mineral products in the industries of metallurgy, construction materials, chemical, and mining, etc.It can produce powder from more than 320 kinds of various non-flammable and non-explosive mineral materials with mohs hardness below 8 and humidity at 6%, such as barite, calcite, limestone, feldspar, dolomite, glass, plaster, insulation materials, etc.The final product size can be adjusted from 80-480 mesh, and the finest product can reach 600 mesh. Main components of rymond mill: Rymond mill structure is composed of main mill, calssifier, pipeline, blower, and also can allocate with stone crusher, elevator, vibrating feeder, cabinet, etc. Raymond mill operating principle: After the material is crushed to be the required size, the materials will be sent to storage hopper by elevator, then sent the material evenly to the space between the roller and ring through the vibrating feeder, to achieve the purpose of crushing through the roller rolling.. The grinded powder will goes into classifier along with the circulation wind of the blower and the standard fineness powder is guided to the cyclone collector and larger size stuff falls back to the grinder for regrinding, exhausted from the discharged tube, then can get finished product. Raymond mill features 1. Compared with ball mill, this machine is with high effeciency, small floor space, small amount investment on time. 2.This mill is one set, one self-contained production system from bulk material to final powder. 3.For this machine, the conveying system adopt sealing gear box, stable trasmission, reliable operation. 4.The main wear parts is made of high-quality mn steel to provide its wearing degree. Standard exporting carton container.