Features: 1. The crushing cavit is deep and without dead zone, which can increase the feeding capacity and capacity; 2. It has a big crushing ratio and even grain shape. 3. The gasket type inlet size makes flexible adjustment posible, and it¡¯s reliable, conveinent, and with a big adjustment range, which can greatly enhance the flexibility of the equipments. 4. The lubrication system is safe and reliable, and it¡¯s quite convinient to change components and there will be less maintenance needed. 5. It has a simple structure, and is quite stable and low in operation cost. 6. The equipment is energy saving: 15%-30% energy can be saved for each single plate, more than twice energy will be saved for the whole system; 7. The size of outlect is quite adjustable, which can meet requirements of different customers. 8. Low noise, less dust; 9. Simple structure, convinient to repair; stable performance, low operation cost; big crushing ratio. Technical parameter of jaw crusher : Mm to inch conversion: 25.4millimeters=1 inch Model max. Feeding Size (mm) discharge Size (mm) capacity (t/h) motor Power (kw) overall Dimensions (mm) weight (t) Pe400¡Á600 350 40-100 15-60 30 1700¡Á1732¡Á1653 6.5 Pe500¡Á750 425 50-100 50-100 55 2035¡Á1921¡Á2000 10.3 Pe600¡Á900 480 65-160 60-130 75 2290¡Á2206¡Á2370 16.5 Pe750¡Á1060 630 80-140 80-180 110 2620¡Á2302¡Á3110 29 Pe900¡Á1200 750 95-165 140-260 110 3789¡Á2826¡Á3025 54.5 Pe1000¡Á1200 850 195-265 315-550 110 3335¡Á3182¡Á3025 57 Pe1200¡Á1500 1020 150-300 400-800 160-220 4200¡Á3750¡Á3820 100.9
Stone crusher.
SM100 Single Cylinder Cone Crusher, designed and made through absorbing the world advanced crushing technology, has achieved world advanced level. It is widely applied to metallurgy, construction, hydropower, transport, chemical and building material industries and suitable for crushing variety of hard and above middle-hard ores and rocks Features: * Great crushing ration and high production efficiency. * Between-layer crushing and more uniform size fraction of end products. * Lower wear parts consumption and operation cost. * Primary and fine crushing can be achievable just by replacing fixed cone. * Advanced hydraulic technologies realize overload protection and hydraulic adjusting discharge opening, simplify crusher structure and lessen its weight. * Reliable and advanced thin oil lubrication extends service life. * Simple maintenance and convenient operation. The capacity charts is a reference for properly using SMH cone crusher and getting to its capacity. Crusher is a component of mining production line, so its characters result from feeder, conveyor, screen, electric motor, drive part and surge bin. Noticing follow factors can enhance crusher capacity and performance. 1.Select crushing chamber according to be crushed materials. 2.Proper matching of feeding particle size. 3.Feeding material is evenly distributed at 360íp around crushing chamber. 4.Automation controls 5.Unobstructed crusher discharge area. 6.Belt conveyor specification is compatible with crusher max capacity. 7.Properly choose screen specification for prescreening and closed-circuit screening.
As a leading manufacturer of whole set of crushing and screening equipment and a solution Provider of aggregate production, shanghai sanme heavy mining machinery co., ltd., provides The customers with high-efficient, reliable and convenient pp series crushing and screening plants, which greatly increases the production Efficiency.The design idea for pp series portable crushing and screening plant is to totally meet the different requirements of mobile crushing Function. This can provide a whole new operation mode that greatly decreases the operation cost. The outstanding performance of pp series portable crushing and screening plants Strong mobility Pp series portable crushing and screening plants is of short length. Different crushing Equipment is separately installed on a independent mobile chassis. Its short wheelbase and tight Turning radius mean they can be transported on highway and moved at crushing sites. Lower transportation cost Pp series portable crushing and screening plant can crush materials on-site. It is unnecessary To carry the materials from one site and then crush them in another one, which can greatly lower The transporting cost for off-site crushing. Flexible configuration and great adaptability According to different requirements of different crushing process, pp series crushing and screening plants can form the following two processes of" crushing first, screening second" or " screening first, screening second". The crushing plant can be composed of two-stage plants or three-stage plants. The two-stage plants consists primary crushing plant and secondary crushing plant, while the three-stage plants includes primary crushing plant, middle crushing plant and tertiary crushing plant, each of which is of high flexibility and can be used individually.
Based on the latest worldly advanced technology, our company designs and produces smh series hydraulic cone crusher. It is widely used in the field of metallurgy, construction, hydroelectric project, road & railway construction, chemical engineering, construction material industry and so on. It is used to crush various hard or medium hard ores and stones. The optimized design of stroke, rotate speed and crushing cavity ensures the high performance of smh cone crusher by increasing the productivity and improving product shape. Features and advantages Smh series hydraulic cone crusher possesses greater superiority than ordinary ones: 1. Larger crushing ratio, high production efficiency, productivity and excellent product shape. Crushing ratio and production efficiency is greatly improved as the increase of power rating and through capacity with the effort of higher rotate speed and stroke. 2. Rational structure, advanced crushing principle and technical data, reliable operation and low cost. All components of crusher are protected by wear resistant material, which reduces the maintenance cost and increase practical lifetime by 30%. 3. Compressive comminution, excellent product shape. A prominent increase in fine material ratio and cubic product content, and massive decrease of elongated flaky particle are achieved through Selective crushing of material, which results from the replacement of single-particle crushing chamber by special inter-particle-grinding crushing cavity. 4. Shorter down time. Sanme cone crusher adopts hydraulic bolt and overload protecting system, which release the impact force gently when uncrushable material is fed into the cavity and revert to original position after material discharged. The brand-new hydraulic cylinders can discharge the material when the machine stops with load. Hydraulic cone crusher has the advantages of safer, more convenient and shorter down time compared with traditional spring type cone Crusher.
Application of jaw crusher: Jaw crusher is a trusted and reliable brand for its high quality and good manufacturing. It specializes in producing jaw crusher which is widely applied to crush high hardness, mid hardness and soft rocks and ores such as slag, construction materials, marble, etc. The pressure resistance strength is under 200mpa, that is, suitable for primary crush. Each model has a large feed opening for its size and an ideal nip angle, giving smooth material flow, high reduction efficiency and high capacity. Their simple design conceals many advanced features that give easy operation, simple maintenance, long life and a low cost per ton. The structure of jaw crusher: The structure of jaw crusher includes main frame, main axle, roller bearings, eccentric shaft, jaw plates, side plates, toggle mechanism, fly wheels and springs. The features of jaw crusher: 1. Jaw crusher is of various types; 2. Jaw crusher is suitable for crushing maximum, medium and minimum stones; 3. The operating principle of jaw crusher is easy to be operated; 4. The structure of jaw crusher is simple and it is easy to maintain; Operating principle: Jaw crusher uses motor as its power. Through the motors wheels, the eccentric shaft is driven by the triangle belt and slot wheel to make the movable jaw plate move by a regulated track. Therefore, the materials in the crushing cavity composed of fixed jaw plate, movable jaw plate and side-lee board can be crushed and discharged through the discharging opening.
Hammer crusher is mainly applied to low abrasion materials with medium hardness and compression strength not exceed 100Mpa. Such as coal, salt, chalk, gypsum, bricks, tiles, limestone, etc. It is also used to crush wood chips with strong fiber structure and tenacity, and the waste from asbestos cement to recycle asbestos fiber, etc. In addition, hammer crusher can be not only applied in crushing line and sand production line, but also applied instead of cone crusher. Performance and features: Hammer crusher has the advantages of high product capacity, high crushing ratio, low power consumption, uniform products partial size, simple structure, compact and light, low investment cost, easy to management, etc. The defects are: when crushing very hard materials, it will cause greater wear of hammer and grate and consume more metal; it needs more maintenance time and uniform feeding of materials; when crushing soft-moist materials, the capacity will become significantly lower and even stop because of material jam. In order to avoid jam, the moisture content of materials should be less than 10%-15%. Model PC400x300 Rotor diameter (mm) 400 Rotor length (mm) 300 Rotor speed (r/min)1100 Max. feeding size (mm)
Hammer crusher is mainly applied to low abrasion materials with medium hardness and compression strength not exceed 100mpa. Such as coal, salt, chalk, gypsum, bricks & tiles, limestone, etc. It is also used to crush wood chips with strong fiber structure and tenacity, and the waste from asbestos cement to recycle asbestos fiber, etc. In addition, hammer crusher can be not only applied in crushing line and sand production line, but also is applied instead of cone crusher.
Jaw Crusher is mainly used to crush kinds of mining stones primarily and the largest compression resistance of the material to be crushed is 320Mpa. The jaw crusher is widely used in mining, metall-urgical industry, building material, highway, railway and chemical industry. Working Principle: The motor transmits power through belt, drives the moving jaw do periodic motion to the fixed jaw surround the eccentric shaft. The angle between toggle plate and moving jaw increases when moving jaw moves up. So the moving jaw closes to the fixed jaw. The stuff will be crushed in this process. The angle of Jaw Crusher between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw of Jaw Crusher moves away from fixed jaw by the pulling of rod and spring, the products after crushing will be discharged from the outlet of Jaw Crusher. Characteristics: High ratio of crushing, homogeneous final grain size, simple structure, reliable working condition, easy maintenance, low operating cost. Type Inlet size (mm) Max Feeding Size (mm) Discharge Size(mm) Power (KW) Capacity (T/H) PE150x250 150x250 125 10-40 5.5-7.5 1-5 PE200x350 200x350 125 15-40 7.5-11 5-16 PE250x400 250x400 210 20-60 15-18.5 5-20.
Ball mill is the key equipment for grinding after the crushing process.It is widly used in the processing of cement, silicate, new building material, refractory material, fertilizer, ferrous and nonferrous metal, glass as well as ceramics. It is used to grind dry or wet ores and other materials of grindability. Feeding size(mm)
The jaw crusher is drived by motor through belt and belt wheels, which makes the movable jaw plate up and down through eccentric shaft.When the movable jaw comes down, the angle between the fixed jaw plate and the movable jaw plate gets smaller, then the materials can be crushed .When the movable jaw plate rises, the angle becomes lauger and the movable jaw plate leaves the fixed jaw plate with the function of tie bar and spring.At the same time the final products are discharged from the lower outlet of the crushing chamber. Specification This series of products have the advantages of big reduction ratio, even granularity, simple structure, liable operation, easy maintenance, economic operation cost, etc. It is widely used for materials with the max crushing compressive strength not more than 320 mpa in the field of mine, metallurgy, building materials, roads, railways, irrigation, chemical industry, etc.
Features It has the characteristics of novel structure, no-bond connecting, high chrome plate hammer, special impact lining plate and energy saving.The finished product is in cubical shape and the discharge granularities can be adjusted.It simplifies the crushing process. Operating principle Impact crusher is a kind of crushing equipment which uses impact energy to crush maters.When getting into the effective area of hammer plates, due to the high speed of striking, the raw materials are thrown onto the impact equipment which is installed above the rotor.Then the materials are rebounded to the effective area of hammer plates and crushed again in the crushing chamber . At last, when the particles reach to the proper size, they will be discharged from the bottom of the machine. Pf impact crusher series The series of products can deal with the materials with max length below 500mm, and the compressive strength below 350mpa. They have the advantage of greater reduction ratio and the final materials are in cubical shape.
The low speed transmission is convenient for maintenance and starting.And the oil mist spray lubrication device ensures the reliable lubricating of big and small gears.Generally, the main motor of the large mill is high pressure asynchronous motor or synchronous motor.So customers should indicate the motor type in order.
Adopting advanced structure of the similar products in foreign countries, the high-rate raymond mill is designated on the basis of modification and renovation of large scale raymond mills. Compared with ball mills, the high-rate raymond mill has higher efficiency, lower power consumption, and smaller area occupying and smaller lump-sum investment. Due to the centrifugal force, the roller mills grind tightly on the rings. Thus it will not influence the output and granularity of the finished products even when the roller and the ring have wear-out in some degree. It is designated for processing superfine powder of over 300 noninflammable and nonexplosive materials with mohs hardness below grade 8 and water content below 6% in the field of mine , chemical industry, building materials, such as barite, calcite, potash feldspar, steatite, marble, limestone, dolomite, fluorite, lime, active carclazyte, active carbon, bentonite, kaolin, cement, phosphorus ore, gypsum, glass, manganese ore, titanium ore, copper mine, chrome ore, refractory materials, heat preservation materials, coal coke, coal fines, black, , bone meal, titanium white powder, , quartz, and so on. The finished products can be adjusted freely from 80 to 325 meshes with max meshes of 600 for some materials.
The jaw crusher is one of our product groups capable to crush easily even the hardest material and the hydraulic system enables the easily and rapidly adjustment of the jaw capacity in accordance withy the product volume, if you wish to lift a material from the machine.
It is also possible to use the high capacity primary impact crusher from our products range for primary and secondary applications. Thanks to the exchangeability of the wearing parts, the extension of machine’s utilization life and handling-convenience is ensured. Further, through the hydraulically open-able case also an ease and rapid maintenance facility is ensured. This product group designed in order to supply you a facile services, is suitable for lifting materials of any hardness.
Application in glass cutting1.To cut the glass of household electrical appliances.2.To cut glass used in shower room.3.To cut glass for architectural decoration, craftwork and auto.It is the only fit way to use waterjet to cut anomalous shapes of glass. It solvesthe problems of making characters and hollowed-out work with glass. That is tosay, all difficulties is readily solved by waterjet cutting. For instance, to makelarge glass screen, glass curtain wall, all kinds of electrical appliance panelsand glass wares. Simple packing.
Application in processing tiles, stones and other building materials.Water cutter is applied in this field much earlier. Currently, the overwhelming majorityin this area use it. They focus on artistic matching. At present, tile matchingand stone matching have expanded all over the world. It is the best way to use water cutter to process tiles. It largely improved productionefficiency and processing precision. It achieved an epochal progress of tilesfurther processing, as it said good bye to the traditional ways of manual grindingand polishing. Presently waterjet cutting is mainly used to make all kindsof complex tile or marble matching . Simple packing.
1. Technical Parameter about UHP PUMP SYSTEM Parameter\Model 4000c Max pressure(Mpa/Psi ) 400/60,000 Working pressure(Mpa) 380 Orifice dia(mm) 0.33 Power(KW/HP) 37/50 L * W * H(M) 1.6*1.1*1.3 Cooling Air Max water flow 3.7L/MIN Shift way Electric shift.
The stone production line is composed of vibrating feeder, jaw crusher, impact crusher, vibrating sieve, belt conveyor and computer controlling board; its design output veries from 50 tons to 500tons per hour. In order to meet the needs of different clients, cone crusher and dust collecting equipment can be added to the prodution line. It can be used in industry like hydroelectricity, building materials, express way, city construction to operate the aggregate of hard limestone, granite, pebble, slag of metallurgy and man-made sand. We can combine different model of machines in the production line according to different technical process. Brief introduction of the stone production line Big block of stone is evenly conveyed to jaw crusher by vibrating feeder via silo for primary crushing. After primary crushing, the stone is sent to impact crusher by belt conveyor for secondary crushing. Then the stone is tronsported to vibrating sieve for screening, thus the stone can be classified into several groups depending on the size. The stone with a necessary size will be sent by belt conveyor to the palce where finished product is piled; otherwise, the stone will be conveyed by belt conveyor to the impact crusher for another crushing, thus a circular production process is formed. Introduction of stone production line performance This production line is highly automatic, except the turning on, turning off and daily maintenance of the equipments no other mannual operations are needed. It enjoys the advantages like: high efficiency, low cost, high throughput, high profit, evenly-sized and good-shaped finished product, meeting the national requirements of rapid need of raw materials.
