Suitable for mass production is a continuous vibration Finishing machine. Feed products produced from the equipment through the committed and then automatically finishing, polishing, and then the automatic sorting, washing, drying (optional) can finish up with a Cycle
The Finishing-machine Polishing tank with a fixed wall and the bottom half is comprised of the rotation and the bottom half of the rotation while rotating parts by centrifugal force and secure the wall-off wheel to push strongly naemyeo incurred on fixed-wall back-off wheel and rotating parts in half fixed back wall pushes back on the materials. Polishing-stone in the process of vortex formation, and parts and rubbing each other by strong cutting force occurs to me, or gloss. Despite these advantages, this machine is something they have not been widespread, in the GAP between the fixed wall and the crank-off wheel is no debris or parts stuck Many times, if a machine fails, the GAP is easy to wear, such as PU Lining Replacement, A / S in the because there were problems. However, we fully resolve these problems, the machine is a revolutionary machine. 1.Polishing-stone pieces or parts to GAP does not pinch, GAP between Pump is dismissed by the water, and water retention OVER-FLOW HOLE in the top of the wall through the machines installed in the lower three-sedimentation-filtration-tank emissions , and precipitation-water is filtered again by the Pump will be put through GAP. In this way, the actual results of using the GAP that occur in this problem did not occur, GAP was gonna wear significantly. 2. The angle of GAP Polishing-stone, or parts have been manufactured so that it caught. 3. Despite improvements such as more, GAP If there is a wear and tear on, GAP and many times without changing the adjustment has been designed to be used. 4. Hydraulic Cylinder used, the compressed air can be used alone without the electric.
The Finishing-machine Polishing tank with a fixed wall and the bottom half is comprised of the rotation and the bottom half of the rotation while rotating parts by centrifugal force and secure the wall-off wheel to push strongly naemyeo incurred on fixed-wall back-off wheel and rotating parts in half fixed back wall pushes back on the materials. Polishing-stone in the process of vortex formation, and parts and rubbing each other by strong cutting force occurs to me, or gloss. Despite these advantages, this machine is something they have not been widespread, in the GAP between the fixed wall and the crank-off wheel is no debris or parts stuck Many times, if a machine fails, the GAP is easy to wear, such as PU Lining Replacement, A / S in the because there were problems. However, we fully resolve these problems, the machine is a revolutionary machine.
Barrel rotation by the distance of the movement parts are Polishing by the friction between the abrasive material and the bulk of the products and machinery, general products that are suitable for demanding, Barrel-box selection of the rotational speed and Polishing time is important.
Product Features: Low vibration, low noise design Central control system High speed / bulk dry Excellent abrasion resistance Labor cost savings
This equipment is "Wheel Finishing & Polishing" is a product designed for the purpose. Within the four principles of abrasive grinding wheel is one trillion Media is a structure that rotates between the surface of each wheel is partially submerged in media, media formed due to collisions between the wheel Wheels - polished surface that is the way. Traditional way by hand, hand grinding wheel and the wheel surface, a worker as a final step of polishing the surface of the wheel to make a worker has worked scrubbing with abrasive materials. Approach this task as very godoel shall manah, time, labor, and expensive, but it was inefficient. The wheel-grinder of the mass-grinding efficiency, as well as improving the quality of processed product and the existing labor-saving in labor-intensive industries, mass production, and wheel-surface, were able to achieve a more perfect gloss. To provide an aesthetic appearance brilliant chrome-plated wheel surface before the coating and the coating must be. If the wheel surface is smooth, chrome-plated wheels, and then remained on the surface grooves and defects on the surface of a larger wheel and will damage the surface of the whole wheel is displayed. Therefore, to the extent necessary to wheel the surface coating on the surface of the wheel to smooth the rough parts of any home and for the purposes of effectively complete removal of this equipment is recommended.
Twist Screen
Perfect automatic rewindable hose reels made of stainless steel 316 made in South Korea with 25-50 m long high pressure hose plus high pressure spray nozzle. For more details, please contact us at park@handakorea.com or phone at
- Typically exceeds multi-media performance, producing foltrate quality comparable to microfiltration systems. - Continuous coagulant addition is not required as the coagulant is bonded directly to the filtration media. - Easily retrofitted into existing filter housings. - Requires no ripening period following backwash. - Backwash rates are reduced significantly as compared to conventional filters.
Plastic handles protect fingers from hot stainless steel lid. Stainless steel lid contains steam during cooking process, and inverts to hold grid and rack when removing food parcels from water bath. Universal rack separates food parcels for even cooking, and prevents parcels from floating to the top, above water line. Positioning it vertically enables you to separate five average-sized pouches. By turning the rack horizontally, it accommodates up to three longer pouches. Control panel and PID controller. Consistent, precision temperature control is mandatory for sous vide cooking. The control panel is used to set temperatures and timers to alert you when your meal is done. See details on next page. Stainless steel inner water bath. Inside the bath is inscribed with Low and High water marks that indicates how much water to initially add to the bath. Remember once you add your food parcels, the level will rise do not exceed the ‘HIGH’ water mark. Ensure that each food parcel you add is submerged completely.
Sous-Vide Nu Classic vacuum cooking : representative Recipes of the Wellness Cook (Wellbeing Cook). 1799 - Britain's Earl Benjamin Thompson originated. In 1960, Georges Pralus made a process. Bruno Goussault made Vaccum vinyl Low-Temperature Cook, the state-of-the-art, called ‘Sous Vide’
Industrial machinery, aviation equipment.Transportation, shipping
Metal tools machine, hobbling, gear shaper, hob grinding, lathe, milling, gear test.
Automotive Spare Parts Of Cars .
The safety boots can be used in pharmaceutical manufacturing and general industry along with industrial sites product. Every year, harmful chemical exposure accidents increase steadily, even in everyday industrial sites easily because it is an accident that causes significant damage, the "safety boots" product can be prevented and kept safe in advance Product List: Chemical Rain Boots (R-2-49) - Anti-slip and anti-static function / Excellent abrasion resistance - Corrosion-resistant stainless steel and anti-slip performance level 1 products Insulated Rain Boots - Available in high voltage current (DC 750V, AC 600V-voltage below 7,000 V) - The inside and outside are made of natural rubber, easy to wash Anti-static safety - High-clean lightweight PU material with minimal fatigue - Ergonomically designed to reduce fatigue even for long hours of wear
The safety boots can be used in pharmaceutical manufacturing and general industry along with industrial sites product. Every year, harmful chemical exposure accidents increase steadily, even in everyday industrial sites easily because it is an accident that causes significant damage, the "safety boots" product can be prevented and kept safe in advance Product List: Chemical Rain Boots (R-2-49) - Anti-slip and anti-static function / Excellent abrasion resistance - Corrosion-resistant stainless steel and anti-slip performance level 1 products Insulated Rain Boots - Available in high voltage current (DC 750V, AC 600V-voltage below 7,000 V) - The inside and outside are made of natural rubber, easy to wash Anti-static safety - High-clean lightweight PU material with minimal fatigue - Ergonomically designed to reduce fatigue even for long hours of wear
The safety boots can be used in pharmaceutical manufacturing and general industry along with industrial sites product. Every year, harmful chemical exposure accidents increase steadily, even in everyday industrial sites easily because it is an accident that causes significant damage, the "safety boots" product can be prevented and kept safe in advance Product List: Chemical Rain Boots (R-2-49) - Anti-slip and anti-static function / Excellent abrasion resistance - Corrosion-resistant stainless steel and anti-slip performance level 1 products Insulated Rain Boots - Available in high voltage current (DC 750V, AC 600V-voltage below 7,000 V) - The inside and outside are made of natural rubber, easy to wash Anti-static safety - High-clean lightweight PU material with minimal fatigue - Ergonomically designed to reduce fatigue even for long hours of wear
Model- 100-s Volume 10- 200 mf Maximum rotation number 3, 000 rpm Consumption of electrical power 1kw Size 300x300x380 Weight 30kg Voltage pressure 220v Emergency shutdown safety magneto door locking catch door-open sensing sensor Vibration sensor
Generator, automobile battery.
Gate v/v, globe v/v, check v/v, ball v/v, butterfly v/v, pumps, meters, fittings.
