Barrel rotation by the distance of the movement parts are Polishing by the friction between the abrasive material and the bulk of the products and machinery, general products that are suitable for demanding, Barrel-box selection of the rotational speed and Polishing time is important.
Custom-made to customers exact specifications is a centrifugal finishing machine .
You want a special grinder for your type of customization is a centrifugal finishing machine
Features:
Low vibration / low noise design, the central control system, high speed / large abrasive diskdrum adjustable, abrasion resistance, labor costs
Product Features.
COMPACT with a design to minimize the installation area
Automatically achieve high quality production by spraying lapping powder.
Constant speed, quiet operation improves workability as.
Product Features:
By adopting water-cooled apparatus was Plate improvement of the thermal deformation of Plate to the integration of the driving parts mounted on GEAREDMOTOR and VECTOR INVERTER SOFT START, SOFT STOP prevent chipping driving single side rapping an existing cross-section of a special design based on the weakness of the central abrasive removes congestion
Product Features:
By adopting water-cooled apparatus was Plate improvement of the thermal deformation of Plate to the integration of the driving parts mounted on GEAREDMOTOR and VECTOR INVERTER SOFT START, SOFT STOP prevent chipping driving single side rapping an existing cross-section of a special design based on the weakness of the central abrasive removes congestion
UA Type ZA or simple selection device built into the machine after completing a finishing damper selection promoted by a network of parts-off wheel and come up and finishing stone selection operation is done go back into the interior parts of the tank is vented to the outside.
The blood of various steel and nonferrous metal tribute series caused burr removed after molding, chamfering, etc. Removal of scale that occurs after the heat treatment is ideal for plating or coating before finishing polishing, polishing is suitable for glossy
Suitable for mass production is a continuous vibration Finishing machine. Feed products produced from the equipment through the committed and then automatically finishing, polishing, and then the automatic sorting, washing, drying (optional) can finish up with a Cycle
The Finishing-machine Polishing tank with a fixed wall and the bottom half is comprised of the rotation and the bottom half of the rotation while rotating parts by centrifugal force and secure the wall-off wheel to push strongly naemyeo incurred on fixed-wall back-off wheel and rotating parts in half fixed back wall pushes back on the materials. Polishing-stone in the process of vortex formation, and parts and rubbing each other by strong cutting force occurs to me, or gloss. Despite these advantages, this machine is something they have not been widespread, in the GAP between the fixed wall and the crank-off wheel is no debris or parts stuck Many times, if a machine fails, the GAP is easy to wear, such as PU Lining Replacement, A / S in the because there were problems. However, we fully resolve these problems, the machine is a revolutionary machine.
1.Polishing-stone pieces or parts to GAP does not pinch, GAP between Pump is dismissed by the water, and water retention OVER-FLOW HOLE in the top of the wall through the machines installed in the lower three-sedimentation-filtration-tank emissions , and precipitation-water is filtered again by the Pump will be put through GAP. In this way, the actual results of using the GAP that occur in this problem did not occur, GAP was gonna wear significantly.
2. The angle of GAP Polishing-stone, or parts have been manufactured so that it caught.
3. Despite improvements such as more, GAP If there is a wear and tear on, GAP and many times without changing the adjustment has been designed to be used.
4. Hydraulic Cylinder used, the compressed air can be used alone without the electric.
The Finishing-machine Polishing tank with a fixed wall and the bottom half is comprised of the rotation and the bottom half of the rotation while rotating parts by centrifugal force and secure the wall-off wheel to push strongly naemyeo incurred on fixed-wall back-off wheel and rotating parts in half fixed back wall pushes back on the materials. Polishing-stone in the process of vortex formation, and parts and rubbing each other by strong cutting force occurs to me, or gloss. Despite these advantages, this machine is something they have not been widespread, in the GAP between the fixed wall and the crank-off wheel is no debris or parts stuck Many times, if a machine fails, the GAP is easy to wear, such as PU Lining Replacement, A / S in the because there were problems. However, we fully resolve these problems, the machine is a revolutionary machine.
Barrel rotation by the distance of the movement parts are Polishing by the friction between the abrasive material and the bulk of the products and machinery, general products that are suitable for demanding, Barrel-box selection of the rotational speed and Polishing time is important.
This equipment is "Wheel Finishing & Polishing" is a product designed for the purpose. Within the four principles of abrasive grinding wheel is one trillion Media is a structure that rotates between the surface of each wheel is partially submerged in media, media formed due to collisions between the wheel Wheels - polished surface that is the way. Traditional way by hand, hand grinding wheel and the wheel surface, a worker as a final step of polishing the surface of the wheel to make a worker has worked scrubbing with abrasive materials. Approach this task as very godoel shall manah, time, labor, and expensive, but it was inefficient. The wheel-grinder of the mass-grinding efficiency, as well as improving the quality of processed product and the existing labor-saving in labor-intensive industries, mass production, and wheel-surface, were able to achieve a more perfect gloss. To provide an aesthetic appearance brilliant chrome-plated wheel surface before the coating and the coating must be. If the wheel surface is smooth, chrome-plated wheels, and then remained on the surface grooves and defects on the surface of a larger wheel and will damage the surface of the whole wheel is displayed. Therefore, to the extent necessary to wheel the surface coating on the surface of the wheel to smooth the rough parts of any home and for the purposes of effectively complete removal of this equipment is recommended.
