Detector Switches is applied to low current circuit (Secondary circuit) push switch
used for electronic equipment.
Appearance of the Switch shall have good finishing and shall have no rust, crack of plating failures.
Terminal Strength of a static load of 3N(306 gf) shall be applied to the tip of terminal in a desired direction for 1 minute. The number of test shall be once per terminal.
Hook Switch is applied to low current circuit hook switch for electronic equipment.
The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar.
Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Lever Switches is applied to low current circuit push switch for electronic equipment.
Appearance of the Switch shall have good finishing, and no rust, crack or plating failures.
Operating force of a static load shall be applied to the tip of actuator in operating direction.
Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal
in a desired direction for 1min. the test shall be done once per terminal.
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment.
Storage temperature range 96 hours maximum for continuous storage over a range
The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure.
Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
108 Electronic Switches Suppliers
Short on time? Let Electronic Switches sellers contact you.
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force
Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment.
Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with
a load of twice of the Actuating force
Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Micro Switch action is PUSH-ON TYPE S.P.D.T
Contact resistance measurements shall be made with a 1KHz ± 200Hz max
DC 5V 1A contact resistance meter.
Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute.
The travel distance for the plunger to come to a stop shall be measured
Tact Switches MT 1101 Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1 kHz small-current contact
resistance meter.
Insulation resistance measurements shall be made following application of DC 100 V
Potential across terminals and frame for one minute
Tact Switch MT 1101 V Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact
resistance meter.
Insulation resistance measurements shall be made following application of DC 100V potential across terminals and frame for one minute.
Tact Switches MT 1102HT Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter.
Insulation resistance Measurements shall be made following application of DC 100V Potential across terminals and frame for one minute
Single Phase to 3 Phase Converter, MY-PS-30 Model, Suitable for 25HP(18.5Kw) 75 Amps 200-240V 3 Phase Motor, DPS Should Be Used for One Motor Only, Input: 220V, Output 200V-240V, Digital Type
DPS is a device that runs a 3 phase motor from single phase power and is a digital type phase converter that can be used for various machines at your workshop and home.
We produce a wide range of product, so please choose the appropriate horsepower DPS according to the installation and specification and application.
- Features of DPS
1. DPS can run 3 phase motor from single phase
2. Digital Type Phase Converter
3. Excellent start-up torque
4. Efficiency is excellent versus other phase converter
5. Small size & easy to install
6. Low failure rate
7. Keeps out dust, moisture, and heat due to the sealed type
8. Designed to be non-flammable
9. Doesnâ??t make any high frequency
10. Lower power consumption
Single Phase to 3 Phase Converter, MY-PS-20 Model, Suitable for 15HP(11Kw) 45 Amps 200-240V 3 Phase Motor, DPS Should Be Used for One Motor Only, Input: 220V, Output 200V-240V, Digital Type
DPS is a device that runs a 3 phase motor from single phase power and is a digital type phase converter that can be used for various machines at your workshop and home.
We produce a wide range of product, so please choose the appropriate horsepower DPS according to the installation and specification and application.
- Features of DPS
1. DPS can run 3 phase motor from single phase
2. Digital Type Phase Converter
3. Excellent start-up torque
4. Efficiency is excellent versus other phase converter
5. Small size & easy to install
6. Low failure rate
7. Keeps out dust, moisture, and heat due to the sealed type
8. Designed to be non-flammable
9. Does not make any high frequency
10. Lower power consumption
We supply you with the variety Chemicals which include many products in the pharmaceutical, food and cosmetic industries and more
with competitive factory price and high quality to meet with your expectation.
We are supplier with the quality Fish Meal and Soybean meal.
Specifications: 1.Best price 2.Protein:65% 70% Fish meal Features Fish contains a variety of nutrients comprise animal tissue, maintain normal metabolism, growth, reproduction is required, has improved the utilization rate of feed and promote animal growth, improve animal disease resistance ability, quality is in the high-grade animal feed irreplaceable quality protein sources. The company's level of fish meal in fish as raw material, the use of modern processing technology, high quality fish after cooking, pressing, drying, crushing and other refining processes. The product has a stable and reliable quality, freshness is good, fish powder flavor, protein content is high, easy to decompose, easy to digest, easy to absorb. Specification Protein: 65% min to 70% Moisture : 10 % max Fat : 10% max Salt : 3 % max Sand : 3 % max Ash : 17% max Antioxidant : 150 ppm min at the time of loading Free from salmonella, melamine, ecoli Advantage 1.High protein 2.Quickly promote heathy and growth 3.Enhance nutrition of poultry 4.Soft powder and good texture 5.Free from any rot odour
