Snap-in type, can be mounted directly on PC board. Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy. Available with anti-ESD ground terminal. Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board. Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy. Available with anti-ESD ground terminal. Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board. Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy. Available with anti-ESD ground terminal. Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Detector Switches is applied to low current circuit (Secondary circuit) push switch used for electronic equipment. Appearance of the Switch shall have good finishing and shall have no rust, crack of plating failures. Terminal Strength of a static load of 3N(306 gf) shall be applied to the tip of terminal in a desired direction for 1 minute. The number of test shall be once per terminal.
Micro Switch action is PUSH-ON TYPE S.P.D.T Contact resistance measurements shall be made with a 1KHz ± 200Hz max DC 5V 1A contact resistance meter. Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute. The travel distance for the plunger to come to a stop shall be measured
Hook Switch is applied to low current circuit hook switch for electronic equipment. The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar. Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Lever Switches is applied to low current circuit push switch for electronic equipment. Appearance of the Switch shall have good finishing, and no rust, crack or plating failures. Operating force of a static load shall be applied to the tip of actuator in operating direction. Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal in a desired direction for 1min. the test shall be done once per terminal.
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature. 45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure. Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment. Storage temperature range 96 hours maximum for continuous storage over a range The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Tact Switches MT 1101 Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1 kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100 V Potential across terminals and frame for one minute
Tact Switch MT 1101 V Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100V potential across terminals and frame for one minute.
Tact Switches MT 1102HT Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance Measurements shall be made following application of DC 100V Potential across terminals and frame for one minute
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment. Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Single Phase to 3 Phase Converter, MY-PS-30 Model, Suitable for 25HP(18.5Kw) 75 Amps 200-240V 3 Phase Motor, DPS Should Be Used for One Motor Only, Input: 220V, Output 200V-240V, Digital Type DPS is a device that runs a 3 phase motor from single phase power and is a digital type phase converter that can be used for various machines at your workshop and home. We produce a wide range of product, so please choose the appropriate horsepower DPS according to the installation and specification and application. - Features of DPS 1. DPS can run 3 phase motor from single phase 2. Digital Type Phase Converter 3. Excellent start-up torque 4. Efficiency is excellent versus other phase converter 5. Small size & easy to install 6. Low failure rate 7. Keeps out dust, moisture, and heat due to the sealed type 8. Designed to be non-flammable 9. Doesnâ??t make any high frequency 10. Lower power consumption
Single Phase to 3 Phase Converter, MY-PS-20 Model, Suitable for 15HP(11Kw) 45 Amps 200-240V 3 Phase Motor, DPS Should Be Used for One Motor Only, Input: 220V, Output 200V-240V, Digital Type DPS is a device that runs a 3 phase motor from single phase power and is a digital type phase converter that can be used for various machines at your workshop and home. We produce a wide range of product, so please choose the appropriate horsepower DPS according to the installation and specification and application. - Features of DPS 1. DPS can run 3 phase motor from single phase 2. Digital Type Phase Converter 3. Excellent start-up torque 4. Efficiency is excellent versus other phase converter 5. Small size & easy to install 6. Low failure rate 7. Keeps out dust, moisture, and heat due to the sealed type 8. Designed to be non-flammable 9. Does not make any high frequency 10. Lower power consumption
Switches.
"Clean Pot" is an ultrasonic humidifier that can be used while floating it in the water. Its innovative structure make separation and assembling more easily without any tools. this humidifier can be separated 100%, so you can wash it all parts. It has flexible design that allows more convenient cleansing like dish-washing.
Used starter alternators.
Pre-painted Hot-Dipped Galvanized Steel Sheet (in Coil) confirming to JIS G3312 CGCC - Coating Top side: 5 micron primer + 20 micron Regular Polyester Paint + Protective Film (50 micron) Back side: 5~7 micron Epoxy service coating - Base metal: Hot-Dipped Galvanized Steel (JIS G3302 SGCC Zinc 120~180g/m2) - Coil Inner Diameter: 508 mm or 610 mm - Coil weight: 2 MT Max. (buyer’s option)
