Tact Lever Switches is applied to low current circuit push switch for electronic equipment. Appearance of the Switch shall have good finishing, and no rust, crack or plating failures. Operating force of a static load shall be applied to the tip of actuator in operating direction. Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal in a desired direction for 1min. the test shall be done once per terminal.
Micro Switch action is PUSH-ON TYPE S.P.D.T Contact resistance measurements shall be made with a 1KHz ± 200Hz max DC 5V 1A contact resistance meter. Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute. The travel distance for the plunger to come to a stop shall be measured
Hook Switch is applied to low current circuit hook switch for electronic equipment. The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar. Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature. 45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure. Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment. Storage temperature range 96 hours maximum for continuous storage over a range The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Tact Switch MT 1101 V Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100V potential across terminals and frame for one minute.
Tact Switches MT 1101 Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1 kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100 V Potential across terminals and frame for one minute
Tact Switches MT 1102HT Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance Measurements shall be made following application of DC 100V Potential across terminals and frame for one minute
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment. Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
CISCO IP Phone 7960G 31 units CISCO IP Phone 7962G 24 units Total 55 units @US$10 each FOB Korea
Dotech's complete solutions against refrigerant leak and noise Accurate measurement with dedicated sensors (low and high pressure refrigerants) Display of saturation temperature of refrigerant All in one (pressure switch and gauge) Easy installation
Virtual COM port mode of USB to RS485 converter ESD and Surge Protection Built-in USB-Powered(no extra power supply) TX-Enable without control signal
Dotech's complete solution against refrigerant leak and noise Refrigerant-dedicated sensor for compressor or condenser fan Smart control (step control, rotating operation, delay time Set, pressure control modes) Digital All-in-one (pressure switches, gauge and controller) Easy installation and reasonable price
Featuring our high-end analyzer, Hercules, and compact S4 wireless hardware, this package is designed to support advanced communication with in-vehicle networks for use in a variety of OEM and supplier applications including diagnostics, simulation, and various custom applications. See the Datasheet for more information. Hercules supports CAN, Class2, and LIN protocols along with full support for GMLAN diagnostics. It also includes graphical display, real-time data playback, and hot-key service sending, among many other features. *For a complete list of all of the Hercules features, please refer to its technical data sheet, and the Gryphon / S-CAT Modules data sheet. The Gryphon S4 hardware is compact, fast, and has built-in support for CAN, along with one expansion slot to support a specific plug-in protocol module. Read about Gryphon Modularity. Additionally, it includes a 10/100T Ethernet connection. Supported Protocols (Gryphon S4 package): CAN (canbus), GMLAN (including SW-CAN for GMW3089 revision 2.2), ISO9141-2, ISO11898 (CAN), ISO15765, J1850 GM (Class 2), J1939, J1979, J2284, J2411 (GM SWCAN), J2534, KWP2000 (ISO14230), LIN. Gryphon Videos: Introduction to using the G2 as a vehicle network communication device to design and development a vehicle network How to use the Tx and Rx functions to send and receive messages on the data bus Common Applications Application Description Monitoring Analysis Diagnosis GRYPHON S4 is also used as an interface for our Hercules CAN Analyzer software tool. Hercules is our high performance Windows analyzer software with protocol support for CAN (canbus), GMLAN, ISO11898 (CAN), ISO15765, J1850 GM (Class 2), J1939, J1979, J2284, J2411 (GM SW), LIN and SWCAN. PV / DV Interface Analysis Diagnosis Included in test stand applications. Available Accessories and Options The following items are available. Part Number Product Name DG-S4-MX16-CABLE An Open Ended cable to the S4's MOLEX connector. WLI-UC-GNM Wireless nano USB adapter. DG-UNVPWR Universal power adapter 100-240VAC/12VDC. DG-OBDII-BOX In-line breakout box to J1962 connectors.
Product Description Category : Laptop J4-UX500
Product Description J4-I4000 Laptop
Processor : Intel Pentium Intel Core Display : 13.3" QHD+(3200 x 1800/WQHD(2560 x 1440) / FHD (1920 x 1080) 16:9 VGA : Intel¢ç HD Graphics HDD : 500GB/1TB RAM : 4G / 8G SSD : M.2 SSD SSD : m
Processor : Intel Pentium Intel Core Display : 13.3" QHD+(3200 x 1800/WQHD(2560 x 1440) / FHD (1920 x 1080) 16:9 VGA : Intel¢ç HD Graphics HDD : 500GB/1TB RAM : 4G / 8G SSD : M.2 SSD
Product Description Hyper 7 Extreme Laptop
